2011 AUDI A5 CABRIOLET change wheel

-~_T_ i_ re _ s_ a_n _ d_ w_ h _e_ e_ ls _________________________________________________ _
& WARNING (conti nu ed )
• If the tire i s not flat and you do not ha ve to change a wheel
immediately, drive at reduced speed to the nearest service station
to check the tire pressure and add air as required.
0 Note
Driv ing without valve stem caps can cause damage to the tire valves.
T o preven t this, a lways make sure that fac tory ins talle d valve stem
caps on all wheels are securely mo unted on the valve.
<£> For the sake of the environment
Under inflated t ires will also increase the fuel consumption .•
Tires and vehicle load limits
There are limits to the amo unt of load or weig ht that any vehicle and
any t ire ca n carry. A veh icle th at is overlo ade d w ill n ot handle well and
is more difficult to stop . Overload ing can not on ly lead to loss of
vehicle co ntro l, bu t can also d amage important pa rts of the vehi cle
and can lead to sudden t ire failure, including a b lowo ut and sudden
deflation that can ca use the vehicle to c rash.
Yo ur safety and t hat of your passengers also depends o n mak ing s ure
that load limits are not e xceeded. Vehicle load incl udes eve rybody
and everyth ing in and on the ve hicle. These load limits are tech nically
refer red to as the veh icle's
Gross Vehicle We ight Rating ("GVWR").
T he "GVWR" includes t he weight of the basic vehi cle, all factory
installed accessories, a fu ll tank of fue l, o il, coo la nt and other fluids
plus maxim um load . The maxim um load includes the number of
passenge rs that the vehi cle is intended to car ry ("seating capacity ")
w ith an ass umed we ight of 150 lbs (68 kg) for each pa ssenger at a
designat ed seating position and the tota l w eight of any l uggage in
the vehicle. If you tow a trai le r, the weight o f the t railer hitch and the tongue weight of the
loaded tra ile r must be included as part of the
veh icle lo ad .
T he
Gross Axle Weight Rating ("GAWR ") is the max imum load t hat
can be a pplied at each of the ve hicle's two axles .
Th e Gross Vehicle Weight Rat ing and the Gro ss Axle Weight Ra ting
are listed on the safety compliance s ticker label located on the
dr iver 's s ide B-pillar. Audi h as 4 seat ing pos it ions, 2 in t he fro nt and
2 in the rear for total seating capacity of 4 . Each seating pos it io n has
a seat belt =>
page 189, "Safety belts" .
Th e fa ct t hat there is an upper lim it to your veh icle 's Gross Vehicle
We ight Rating means that the total weight of whatever is being
c arrie d in t he ve hicle (incl uding t he weight o f a trail er hi tch and the
tongue weig ht of the loaded tra iler) is limited . The more passengers
in the veh icle or p assenge rs who are he avier than the st anda rd
we ights assumed mean that less we ight can be carried as luggage.
Th e tire pressure labe l o n yo ur Audi a lso lists the max imum combine d
we ight of alt of the o ccupants and l uggage or o ther cargo that the
vehicle ca n carry . For t he locat ion of the label=>
page 300, fig. 22 7.
& WARNING
Overloading a vehicle can cause loss of vehicle control, a crash or
other accident, serious personal injury, and even death.
• Carrying more weight than your vehicle was de signed to carry
will prevent the vehicle from handling properly and increase the
risk of the loss of vehicle control.
• The brakes on a vehicle that has been overloaded may not be
able to stop the vehicle within a safe di stan ce.
• Tires on a vehicle that has been o verloaded can fail suddenly ,
including a blowout and sudden deflation, causing loss of control
and a crash .
• Always make sure that the total load being transported -
i ncluding the weight of a trailer hitch and the tongue weight of a .,_

IIIIL-_T.:..:..: ir:....:e~ s=---= a~ n:..:..: d:......: w..:....:.. h:....:e~ e= ls=--------------------------------------------------
The tire pressure monitor ing must be reset via rad io or MMI* each
t ime t he press ures are adjusted (e.g. w hen sw itching be tween p artial
and full load pressure) o r after changing or replac ing a tire on yo ur
vehicle => page
316. You ca n find t he recommen ded tire pressures
for your veh icle on the labe l on driver's s ide B-pilla r => page
300.
Tire tread circ umference and vibrat ion characteristics can change and
c a u se a tir e pressure war ning if:
• the t ire pressure in one or more tires is too low,
• t he tire ha s structur al dam age,
• the tire press ure was changed, wheels rotated or rep laced but the
TPM S was no t reset=> page
316.
Warning symbols
1..1' Loss of press ure in at least one tire=> &. Check the tire or tires
and replace or repair if necessary. The indicator light (• in the instru­
me nt cluste r a lso illuminates=> page
12. Check/correct the p res­
sures o f all four tires and reset TPMS via rad io or MMI *.
rr :; (T ire Pressu re M on itor ing System) Tire pres sure! System
malfunction.
If T ,.;> appears after switching the ignition on or w hile
dr iv ing => page
315, fig. 23 3 and the indica to r lig ht 'in th e instr u­
me nt clus ter b links for approx ima tely one m inute and the n stays on,
there is a system ma lf u nct io n. See your authorized Audi dealer as
soon as poss ible.
& WARNING
• If the tir e pres sure indicator appears in the instrument cluster
display, one or more of your tires i s significantly under-inflated.
Reduce your speed immediately and avoid any hard steering or
braking maneuvers. Stop as soon a s possible and check the tires
and their pressures . Inflate the tire pressure to the proper pres­
sure as indicated on the vehicle 's tire pressure label=>
page 300.
Driving on a significantly under -inflated tire causes the tire to
overheat and can lead to tire failure. Under -inflation also is likely
to impair the vehicle's handling and stopping ability.
& WARNING (co ntinued )
• The driver is re sponsible for maintaining the correct tire pres­
sures . You must check the tire pres sures regularly .
• Under certain conditions (such as a sporty driving style , winter
conditions or unpaved roads) , the pressure monitor indicator may
be delayed.
• Ask your authorized Audi dealer if run-flat tires may be used on
your vehicle . Your vehicle registration becomes invalid if you u se
the se tires when not permitted. Damage to your vehicle or acci­
dents could also result.
[ i ] Tips
• T he tire pressure monito ring system stops working when there is
an ES P/ABS malf u nctio n.
• Using snow cha ins may res ult in a system ma lf u n ct ion .
• The tire pressure mon itor ing system on your Au di was calibrated
using t ires with the "AO" or "RO " id ent ificat ion . We re comme nd
using these tires. •
Applies to vehicles: with tire p ressure monito ring sys tem
Reset tire pressure monitoring system
I f the tire pressure is adjus ted, wheels are rotated or
changed, th e TPfvf S must b e re set via radio or fv1fv1 I*.
- Turn on the ign it ion .
- Sele ct: Fu nct ion bu tton
[C AR]> Tire pressure monitoring
> Store now.
[ i ] Tips
Before resett ing the TPMS, the current pressures of all four t ires
mus t co rrespo nd to the specifie d val ues. A djust the tire pre ssure and
~

What do I do now? Ill
----------------
& WARNING (continued)
• Make sure that passengers wait in a safe place away from the
vehicle and well away from the road and traffic.
• To help prevent the vehicle from moving suddenly and possibly
slipping off the jack, always fully set the parking brake and block
the wheel diagonally opposite the wheel being changed with the
folding chocks or other objects. When one front wheel is lifted off
the ground, placing the Automatic Transmission in "P" (Park) will
not prevent the vehicle from moving.
• Before you change a wheel, be sure the ground is level and
firm. If necessary, use a sturdy board under the jack.
• After installing the inflatable spare tire, make sure that you
replace the flat tire/wheel in its storage area properly and tighten
the knurled retaining screw securely.
0 Note
If you are changing the wheel on a steep incline, use a rock or similar
object to block the opposite wheel to prevent the vehicle from
moving.
[I) Tips
Obey all laws.•
Changing a wheel
When you change a wheel, follow the sequence described
below step-by-step and in exactly that order.
1. Remove the decorative wheel cover*. For more details see
also~
page 322, "Decorative wheel covers" .
2. Loosen the
wheel bolts=> page 323.
Safety first
3. Locate the proper mounting point for the jack and align
the jack below that point~
page 323.
4. Lift the car with the jack~ page 323.
5. Remove the wheel with the flat tire and then install the
spare tire~ page 325.
6. Tighten all wheel bolts lightly.
7.
Lower the vehicle with the jack.
8. Use the wheel bolt wrench and
firmly tighten all wheel
bolts in a crisscross pattern~
page 323.
9. Replace the decorative wheel cover*.
& WARNING
Always read and follow all WARNINGS and information=> & in
"Raising the vehicle" on
page 323 and => page 326. •
After changing a wheel
A wheel change is not complete without the doing the
following.
- Store and secure the wheel you replaced in the spare
wheel well.
- Replace the tools and the jack in their proper location.
- Check the
tire pressure of the spare tire as soon as
possible.
- As soon as possible, have the
tightening torques on all
wheel bolts checked with a torque wrench. The correct
tightening torque is 90 ft lb (120 Nm).
- Have the flat tire
replaced as soon as possible.
Vehicle care Do-it-yourself service Technical data

llffl.___W __ h_a_ t_ d_ o_ I_ d_o_ n_ o_w _ ? _____________________________________________ _
• Pull the r eversible blade from the sc rewdriver before you use the
hexagon al socke t in the h an dl e to tur n t he whee l bolts.
• When mounting tires with
unidirectional tread design make sure
t he t read p attern is po inte d the rig ht way =:>
page 326.
• The wheel bo lts shou ld be clean and easy to turn. Check for dirt
and cor rosion on the mat ing surfa ces of both the whee l and the hub.
Remove all d irt from these surfaces before remounting the whee l.•
Tires with unidirectional tread design
Tires with unidirectional tread design must be mounted
with their tread pattern pointed in the right direction.
Using a spare tire with a tread pattern intended for
use in a specific direction
When using a spare tire w ith a tread pattern intended for use in a
spe cific d irec tion, please note the follow ing :
• The direction of rotation is marked by an
arrow on the side of the
tire .
• If the spare tire has to be installed in the incorrect d irect ion, use
t he spare tire only temporari ly since the tire wi ll not be ab le to
achieve its optimum performance characte rist ics with regard to
aquap lan ing, noise and wear.
• We recommend that you pay particular attention to this fact
during wet weather an d that you adjus t you r speed to match road
conditions.
• Rep lace t he fl at t ire w ith a new one and have it ins talled on your
vehicle as soon as possible to restore the handling advantages of a
unidi rectional tire .•
Notes on wheel changing
Please read the in format ion =:> page 307, "New tires and replac ing
t ires and wheels" if yo u are go ing to use a spare ti re wh ich is diffe rent
from the tires on your vehicle .
After you change a tire :
• Che ck the tire pre ssure on the spare immediat ely after installa­
tion .
• Have the wheel bo lt tightening torque checked with a torqu e
wren ch as soon as possible by your autho rized Aud i deale r or a qual ­
ified work shop .
• With steel and all oy wheel rims , the wheel bolts are co rrectly
tightened at a torque of 90 ft lb (120 Nm ).
• If you noti ce that the wheel bolts are corroded and difficult to
turn while changing a tire, they should be rep laced before you chec k
the tightening torque .
• Replace the flat tire with a new one and have it installed on your
v ehicle a s soon a s poss ible. Remount the wheel co ve r.
Until then, drive with extra car e and at reduced speed s.
& WARNING
• If you are going to equip your veh icl e with tires or r ims whi ch
differ from those which were factory installed, then be sure to
read the information =:>
page 307, "New tires and replacing ti re s
and wheels".
• Alw ays make sure the damag ed wh eel or ev en a flat tir e and
the j ack and tool kit are properl y secured in the luggage compart­
ment and ar e not loo se in th e pas senger compartment.
• In an a ccident or sudden maneuver they could fl y forward,
i n juring anyone in th e ve hicle .
• Alw ay s s tore dam aged wheel , jack and t ool s se cure ly in the
luggage compartment. Othe rwi se , in an ac cident or sudden

___ D_ a_t _a _____________________________________________________ _
Data
Applie s to ve hicle s: with 2 .0 lit er 4- cyl. engin e
211 hp, 2.0 liter 4-cyl. engine
Engine data
Max imum outpu t SAE net
Max imum torque SAE net
No. of cy linde rs
Displacement
Stroke
Bore
Compression rat io
Fu el
Dimensions (approx .)
Length (with license plate bracket)
Width (with outside mirrors fol ded)
He ight (un loaded)
Turning circle d iameter (curb to curb)
Capacities (approx.)
Fuel tank
- Total capacity
- Reserve (of to tal c apaci ty)
Windshield and headlight * washer fluid container
Engine oil
with filter change hp@rpm
lb-ft@
rpm
C ID (cm
3
)
in (mm)
in (mm) 2
11 @ 4300- 6000
259@ 1500-4200
4
12 1 (198 4)
3.65 (92.8)
3.25 (82.5)
9 .6 : 1
Premium unleaded (91 AKI) R eco mmend ed for maximum engi ne per formanc e. Fur ­
ther details ~
page 274, "Gasoline"
in (mm)
in (mm)
i n (mm)
ft (m)
gal (Liters)
g al (Liters)
qua rts (liters)
quar ts (lite rs) 182
.0 (4625)
79 .5 (2020)
54.4 (1383)
36.4 (11. 1)
front wheel drive 17.1 (65.0)
1.8 -2.4 ( 7-9)
4.8 (4 .5)
4.9 (4.6) all whee
l drive
16.8 (64 .0)
1.8- 2.4 (7 -9)
4 .8 (4 .5)
4 .9 (4.6)
•

______________________________________________ C _o_ n _ s_u_ m_ e_r_ I_n _f_ o_ r_m _ a_t_ i_ o _ n __ _
& WARNING (co ntinued )
• Always remove the ign ition key before anyone gets under the
vehicle.
• Alway s support your vehicle with safety stands if it is nece ssary
to work underneath the vehicle . The jack supplied with the veh icle
is not adequate fo r thi s purpose and could collap se causing
serious personal injury.
• If you must work underneath the vehicle with the wheels on
the ground, always make sure the vehicle is on level ground, that
the wheels are always securely blocked and that the engine cannot
be started.
• Always make sure the transmi ssion selector lever (automatic
transmi ssion) is in "P " (Park po sition ) and the park brake is firmly
applied.
<£> For the sake of the environment
• Changing the engine settings will adverse ly affect emission levels .
Thi s is det rimenta l to the environme nt and increases fue l co nsump­
tion.
• Always obse rve environmen tal regulat ions when d ispos ing of o ld
engine oil, used b rake fl uid, di rty e ngine coo lant, spent batter ies or
worn out t ires .
• Undeployed a irbag modules and pretensioners m igh t be classifie d
as Perchlorate Mater ia l -spec ial hand ling may apply, see
www.dtsc.ca.gov/hazardouswaste/pe rchlorate . When the vehicle or
parts of t he rest raint system includi ng ai rbag modu les safety belts
with pretens ioners are sc rapped, all applicable laws and regulat ions
m ust be ob served. Yo ur author ized Au di dealer is f amiliar wi th these
requirements and we recommend that you have your dealer perform
t his servi ce for yo u. •
Safety first
Additional accessories,
modifications and parts
replacement
Additional accessories and parts
replacement
Always co nsult an autho riz ed Audi d ealer bef ore
purchasing acces sories.
Yo ur vehicle incorporates the latest safety design feat ures ens uring a
high standard of active and pass ive safety .
Th is safety could be compromised by non-approved changes to the
veh icle . F o r th is reaso n, if p arts have to be rep la ce d , ple ase obse rve
the following points when installing addit ional accessories:
Approved Audi accessories and genuine Au di parts are available from
au thori zed Aud i dea le rs .
These dea lers a lso have the necessary facilities, tools and tra ined
specialists to i nstall t he pa rts and ac cesso ries p roperly.
& WARNING
Using the wrong spare parts or u sing non-approv ed accessories
c an cause damage to the vehicle and serious personal injury.
• Use only accessories expressly approved by Audi and genuine
Audi spare parts
• These parts and accessories have been specially designed to be
used on your vehicle.
• Never install accessories such as telephone cradles or beverage
holder s on airbag covers or within the airbag deployment zones .
Doing so will increase the risk of injury if airbags are triggered in
an a ccident!
• Before you check anything
in the engine compartment, always
read and heed all WARNINGS~
page 272. .,
Do-it,yourself service Technical data