2011 Alfa Romeo Giulietta maintenance reset

13
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Alfa Romeo CODE fault/
alarm fault (amber)
(for versions/markets, where provided)
The warning light (or symbol on the display) will come
on (on some versions, with a message on the display) to indicate
an Alfa Romeo CODE system or alarm fault(for versions/markets,
where provided): In this case, contact Alfa Romeo Authorized Ser-
vices.
Break-in attempt
If this warning light flashes or, on some versions, if the symbol
appears in the display (together with the associated message) this
indicates a break-in attempt. Contact Alfa Romeo Authorized Ser-
vices as soon as possible.
Y
Glow plug preheating
(diesel versions) (amber)
When the key is turned to MAR, the warning light
comes on and it will go out when glow plugs reach the
preset temperature. THE engine may be started immediately af-
ter the warning light goes out.
IMPORTANT In mild or high temperature conditions, the warning
light comes on for a very short time only.
Glow plugs preheating fault
(diesel versions)
The warning light will flash (a message in the display will appear
on the display, on some versions) to indicate a fault in the glow
plugs preheating system. Contact Alfa Romeo Authorized Services
as soon as possible to eliminate the fault.
m
Water in fuel filter
(diesel versions) (amber)
The warning light remains on constantly when driving
(together with a message in the display), to indicate the
presence of water in the diesel fuel filter.c
The presence of water in the fuel system circuit may
cause severe damage to the injection system and
irregular engine operation. If the
cwarning light
comes on in the instrument panel (together with a mes-
sage in the display) contact Alfa Romeo Authorized Ser-
vices as soon as possible to bleed the system. Water may
have entered the tank if this appears immediately after
refuelling: if this happens, switch the engine off immedi-
ately and contact Alfa Romeo Authorized Services.

33
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Button volume (Button volume adjustment)
With this function it is possible to adjust (to eight levels) the vol-
ume of the acoustic signal sounding when the MENU SET button
is long pressed to exit a sub-menu and return to the standard menu.
To set the desired volume, proceed as follows:
– briefly press the SET ESC button: the previously set volume lev-
el will be displayed;
– press the button “
Ò▲“ or “▼“ to adjust the volume; an
acoustic signal equal to the volume level being selected is sound-
ed during this adjustment;
– briefly press the SET ESC button to go back to the previous screen
or hold the button down to go back to the standard screen with-
out saving.
On versions with reconfigurable multifunction display, the volume
level is represented by bars.
Belt reminder (Buzzer/reactivation for S.B.R.
signally)
(for versions/markets, where provided)
This function will only be displayed after the S.B.R. system
has been deactivated by an Alfa Romeo Authorised Service Provider
(see “S.B.R. system” in chapter 2).
Ser vice (Ser vice schedule)
With this function is possible to view information on servicing dead-
lines depending on kilometres travelled or daily intervals. The Ser-
vice function also shows the interval (in kilometres or miles) be-
fore the next engine oil change is due.
This information can be consulted as follows:
– briefly press the SET ESC button, which makes the display show
the service interval in km or mi according to the previous setting
(see “Distance measures” paragraph); press the SET ESC button
to return to the menu screen or hold the button down to return to
the standard screen.
IMPORTANT According to the “Planned Maintenance Programme”,
the car must be serviced every 30,000 km (1.4 petrol versions)
or 35,000 km (1750 Turbo petrol and diesel versions). This mes-
sage is displayed automatically when the key is turned to MAR,
from 2,000 km (or equivalent value in miles) when the next ser-
vice is due and is displayed again every 200 km (or equivalent
value in miles). Below 200 km the signals become more frequent.
The indication will appear in kilometres or miles depending on
the unit of measurement settings. When the next scheduled ser-
vice is approaching and the key is turned to MAR, the word Ser-
vice will appear on the display, followed by the number of kilo-
metres or miles left. Contact Alfa Romeo Authorized Services where
the “Planned Maintenance Programme” operations will be per-
formed and the message will be reset.

36
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
TRIP COMPUTER
GENERAL INFORMATION
The Trip Computer displays information on car operation when
the key is turned to MAR. This function is composed by separate
trips, called “Trip A” and “Trip B” which can monitor the entire mis-
sion (journey) in a reciprocally independent manner.
Both trips can be reset (start of a new journey).
“Trip A” is used to display the figures relating to:
– Autonomy
– Distance travelled
– Average consumption
– Current consumption
– Average speed
– Travel time (driving time). With the function “Trip B” is possible to display the figures relating to:
– Distance travelled B
– Average consumption B
– Average speed B
– Journey time B (driving time).
“Trip B” may be turned off (see “Trip B on” paragraph). “Range”
and “Instant consumption” parameters cannot be reset.

39
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
TRIP button 0.00
This is located on the right stalk (fig. 13). With the ignition key
turned to MAR, this button displays the values described above and
resets then before a new mission:
– short press: values display;
– long press: values reset and start of a new mission.
New journey
It begins after a new reset is made:
– “manual” resetting by the user, by pressing the relevant button;
– “automatic” resetting, when the “Trip distance” reaches
99999.9 km or when the “Travel time” reaches 999.59 (999
hours and 59 minutes);
– after each disconnection and subsequent reconnection of the bat-
tery.
IMPORTANT The reset operation when “Trip A” details are being
displayed resets the information associated with this function only.
IMPORTANT The reset operation when “Trip B” details are being
displayed resets the information associated with this function only.
Start trip procedure
With ignition key turned to MAR, carry out the reset operation by
pressing and holding down the TRIP 0.00 button for longer than
2 seconds.
Exit Trip
You can automatically exit the TRIP function once all the values
have been displayed, or by holding the MENU ESC button down
for more than 1 second.
fig. 13A0K0096m

71
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
CLIMATE CONTROL SYSTEM COMPRESSOR
Press C to turn the compressor on/off (the LED on the button will
light up when the compressor is on). The system remembers that
the compressor has been switched off, even after the engine has
stopped.
When the compressor is switched off the system deactivates air re-
circulation to prevent the windows from misting up and deactivates
the AQS function. In this case, although the system is capable of
maintaining the required temperature, the AUTO LED will go out.
The temperatures will flash for a few seconds if the required tem-
perature cannot be maintained.
To restore automatic control for switching on the climate control
compressor, press C button again or press the AUTO button.
With compressor off:
❍if the outside temperature is higher than the set one, the sys-
tem will not be able to satisfy the request. The temperature
value will then flash on the display for a few seconds;
❍the fan speed can be manually reset.
When the compressor is on and the engine is running, manual ven-
tilation cannot drop under the maximum speed (only one LED on).
IMPORTANT With the climate control compressor off, it is not pos-
sible to admit air into the passenger compartment with a tempera-
ture below the outside temperature; moreover, under certain envi-
ronmental conditions the windows could mist up very quickly since
the air cannot be dehumidified.
RAPID WINDOW DEMISTING/DEFROSTING
(MAX-DEF function)
Press-to turn windscreen and side window demisting/defrosting
function on (LED on button lit). The climate control system carries
out the following operations:
❍switches on the climate control compressor when climatic con-
ditions allow;
❍turns air recirculation off;
❍sets maximum air temperature (HI) in both zones;
❍sets proper fan speed according to the engine coolant tem-
perature;
❍directs air flow to the windscreen and front side windows vents;
❍the heated rear windscreen is turned on
❍shows fan speed (LED G lit).
IMPORTANT The MAX-DEF function will remain on for approximately
3 minutes from when the engine coolant reaches adequate tem-
perature.
The LED on the AUTO button will go out when the function is on.
With the function activated the only possible manual adjustments
are adjusting the fan speed and the turning the heated rear wind-
screen off. By pressing B, C,
-or AUTO buttons, the climate
control system will turn the MAX-DEF off.

79
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
CRUISE CONTROL
(for versions/markets, where provided)
GENERAL INFORMATION
This is an electronic driving aid that allows you to drive at a speed
of above 30 km/h on long and straight dry roads (e.g. motor-
ways), at a preset speed without having to press the accelerator
pedal. It is therefore not recommended to use this device on coun-
try roads with traffic. Do not use it in town.
TURNING THE DEVICE ON
Turn ring A-fig. 43 to ON. The device cannot be turned on in 1stor
reverse gear. It is advisable to engage it in 5thgear or higher.
When travelling downhill with the device engaged, the car may
slightly exceed the preset speed. When the device is activated,
Ü
light comes on together with the relevant message on the instru-
ment panel (for versions/markets, where provided).
REAR WINDOW WIPER/WASHER
(for versions/markets, where provided)
Activation
This only operates with the ignition turned to MAR.
Turn B ring fig. 41 from position
Oto position 'to turn on the
rear window wiper as follows:
❍intermittent operation if the windscreen wiper is off;
❍synchronised operation (but with half-stroke frequency) when
the windscreen wiper is on;
❍continuous operation with reverse engaged and windscreen
wiper on.
With reverse gear engaged and windscreen wiper on, the rear win-
dow wiper is activated in continuous mode. Pushing the stalk to-
wards the dashboard (temporary position) the rear window wash-
er jet will activate.
Keeping the stalk pushed for more than half a second also the rear
window wiper will activate. Releasing the stalk will activate the
smart washing function, as described for the windscreen wiper.
fig. 43A0K0098m

80
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
INCREASING THE STORED SPEED
Press the accelerator and store the new speed or move the stalk
upwards (+). Each movement of the stalk will correspond to an
increase in speed of about 1 km/h, while keeping the stalk held
upwards the speed will continuously increase.
REDUCING THE STORED SPEED
Deactivate the device and store the new speed or move the stalk
downwards (–) until the new speed is reached. It will then auto-
matically be stored. Each movement of the stalk will correspond
to a reduction in speed of about 1 km/h, while keeping the stalk
held downwards will continuously reduce the speed.
TURNING THE DEVICE OFF
To release:
❍turn the A ring fig. 43 to OFF;
or
❍stop the engine;
or
❍press the brake pedal, the clutch or the accelerator; in this
last case the system is not actually turned off but the system
gives priority to the acceleration request. The device still re-
mains active, without the need to press the RES button to re-
turn to the previous condition once acceleration is concluded.
STORING THE SPEED
Proceed as follows:
❍turn A ring fig. 43 to ON and press the accelerator until the
car reaches the desired speed;
❍move the stalk upwards (+) for at least one second, then re-
lease it. The speed is now stored and you can therefore release
the accelerator pedal.
If needed (when overtaking for instance), you can accelerate sim-
ply by pressing the accelerator pedal; when you come off the ped-
al, the car will return to the speed memorised previously.
RESTORING STORED SPEED
If the device was disengaged - for example by pressing the brake
or clutch pedal - the stored speed can be reset as follows:
❍accelerate gradually until reaching a speed approaching the one
stored;
❍engage the gear selected at the time of speed storing;
❍press RES button (B-fig. 43).

81
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
CEILING LIGHTS
FRONT CEILING LIGHT fig. 44
A Switch is used to switch the ceiling lights on/off.
A Switch positions:
❍central position (position 1): C and D lights come on/off when
the doors are opened/closed;
❍pressed to the left (position 0): C and D lights are always off;
❍pressed to the right (position 2): C and D lights are always on.
Lights are gradually switched on/off.
Turning the device off automatically
The device is automatically turned off in the following cases:
❍if the ABS or VDC systems intervene;
❍with car speed below the preset limit;
❍in the event of system fault.
Do not position the gear lever in neutral when dri-
ving with the device on.
In the event of faulty operation or fault, turn the
ring A-fig. 43 to OFF and contact an Alfa Romeo
Authorised Service.
fig. 44A0K0061m