Page 106 of 324

105
Continued
Controls
Operating the Switches Around the Steering Wheel
Turn Signals
Light Switches
Turn Signals
The turn signals can be used when the
ignition switch is in ON
II
.
Rotating the light switch turns the lights on
and off, regardless of the position of the
ignition switch.
High beams
Push the lever forward until you hear a click. Low beams
When in high beams, pull the lever back to
return to low beams. Flashing the high beams
Pull the lever back, and release it.
Manual Operation
Light Switches
If you remove the key from the ignition switch while
the light is on, a chime sounds when the driver’s
door is opened.
When the lights are on, the lights on indicator in
the instrument panel will be on.
Indicators
P. 6 4
Repeatedly turning the headlights on and off
reduces the life of the HID headlight bulbs.
If you sense that the level of the headlights is
abnormal, have the vehicle inspected by a dealer.
Do not leave the lights on when the engine is off
because it will cause the battery to discharge.
Light Switches
Right Turn
Left Turn
High Beams
Low BeamsFlashing the
high beams
Turns on side marker, tail and
license plate lights Turns on headlights, parking,
side marker, tail, and license
plate lights
Page 144 of 324

Audio System Basic Operation
Playing the AM/FM Radio
143
Features
Continued
Playing the AM/FM Radio
AM/FM Button
Press to select a band.
TITLE Button
Press to switch the RDS name
on and off.
CATEGORY Bar
Press either side to display and
select an RDS category.
SCAN Button
Press to sample each of the strongest stations
on the selected band for 10 seconds.
To turn off scan, press the button again.
VOL /
Knob
Press to turn the audio system ON and OFF.
Turn to adjust the volume.
Preset Buttons (1-6)
To store a station:
1. Tune to the selected station.
2. Pick a preset button and hold it
until you hear a beep.
To listen to a stored station, select a
band, then press the preset button.
SKIP Bar
Press and hold to search up and
down the selected band for a station
with a strong signal.
A.SEL (Auto Select) Button
Press to scan both bands and store
the strongest station in each preset.
To turn off auto select, press the
button again. This restores the
presets you originally set.
Selector Knob
Turn to tune the radio frequency.
Page 162 of 324

161
General Information on the Audio System
Features
Subscribing to XM
® Radio
1. You need your radio ID ready before registering for subscription.
To see the ID in the display: Turn the selector knob until "0" appears.
2. Have your radio ID and credit card number ready, and either call or visit the XM
®
website to subscribe.
Receiving XM
® Radio
Press the
(XM
®) button and stay in this mode for about 30 minutes until
the service is activated. Make sure your vehicle is in an open area with good
reception.
XM
® Radio Display Messages
LOADING: XM
® is loading the audio or program information.
OFF AIR: The channel is not currently broadcasting.
UPDATING: The encryption code is being updated. Channels 0 and 1 still work
normally.
NO SIGNAL: The signal is too weak in the current location.
--------: No such channel exists, the channel is not part of your subscription, or the
artist or title information available.
ANTENNA: There is a problem with the XM
® antenna. Contact a dealer.
Subscribing to XM
® Radio
Contact Information for XM
® Radio:
US: XM
® Radio at www.xmradio.com or (800) 852-
9696
Canada: XM
® Canada at www.xmradio.ca, or (877)
209 - 0079
Receiving XM
® Radio
The XM
® satellites are in orbit over the equator;
therefore, objects south of the vehicle may cause
satellite reception interruptions. Satellite signals
are more likely to be blocked by tall buildings and
mountains the farther north you travel from the
equator.
You may experience reception problems under the
following circumstances:
In a location with an obstruction to the south of
tyour vehicle.
In tunnels tOn the lower level of a multi-tiered road tLarge items carried on the roof rack t
XM
®Radio Service
Page 253 of 324
Replacing Light Bulbs
Front Turn Signal/Parking/Side Marker Light Bulbs
252Maintenance
Front Turn Signal/Parking/Side Marker Light BulbsWhen replacing, use the following bulbs.
Front Turn Signal/Parking/Side Marker: 21/5WTurn the steering wheel and pull the inner fender back in the same way as when
replacing the low beam headlights.
Changing the Low Beam Headlight
P. 2 5 0
1. Turn the socket to the left and remove it.
2. Push in the old bulb, rotate to the left until
it unlocks, and remove.
3. Insert a new bulb.2. Remove the coupler.
It can be removed by pushing the tab.
3. Rotate the old bulb to the left to remove.
4. Insert new bulb.
BulbSocket
Bulb
Ta b
Coupler
Page 254 of 324
Replacing Light Bulbs
Side Turn Signal/Emergency Indicator Light Bulbs
253
Continued
Maintenance
Brake Light, Taillight, Rear Turn Signal Light and
Rear Side Marker Light BulbsWhen replacing, use the following bulbs.
Brake/Taillight: 21/5W
Rear Turn Signal Light: 21W
Rear Side Marker Light: 3CP
1. Pull out and remove the cover.
Side Turn Signal/Emergency Indicator Light BulbsDoor mirrors have the side turn lights. Have an authorized Acura dealer inspect
and replace the light bulbs.
Cover
Page 303 of 324