2011 ACURA RL key

ÛÝ
To exit KEYLESS ACCESS BEEP
without changing the current setting,
select EXIT by pressing the INFO
( / ) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
keyless access beep setup.
Multi-Inf ormation Display
114
10/08/04 19:00:52 31SJA660_119
ProCarManuals.com

Û
Ý
Û
Ý
ÛÝ
ÛÝ
AUTO DOOR LOCK
AUTO DOOR UNLOCK
There are five settings to choose
f rom in the door/window setup:
While CUSTOMIZE GROUP is
shown on the multi-inf ormation
display, select DOOR/WINDOW
SETUP by pressing the INFO ( /
) button, and then press the SEL/
RESET button.
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button, until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. SECURITY RELOCK TIMER DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGMENT
Door/Window Setup
Multi-Inf ormation Display
122
seepage123
seepage125
seepage127
seepage129
see page 131
Press the or button.
Press the SEL/RESET button.
10/08/04 19:02:05 31SJA660_127
ProCarManuals.com

ÛÝ
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
keyless lock acknowledgment setup.To exit KEYLESS LOCK
ACKNOWLEDGMENT without
changing the current setting, select
EXIT by pressing the INFO ( / )
button, then press the SEL/RESET
button. The screen goes back to
CUSTOMIZE MENU.
Multi-Inf ormation Display
130
10/08/04 19:03:15 31SJA660_135
ProCarManuals.com

µ
µ µ
Push down on the
lever to signal a lef t turn and up to
signal a right turn. To signal a lane
change, push lightly on the lever,
and hold it. The lever will return to
center when you release it or
complete a turn.
The rotating switch
on the lef t lever controls the lights.
Turning this switch to the ‘‘ ’’
position turns on the parking lights,
taillights, instrument panel lights,
side-marker lights, and rear license
plate lights.
Turning the switch to the ‘‘ ’’
position turns on the headlights. If
you leave the lights on with the
ignition switch released af ter turned
to the LOCK (0) position or when
the built-in key is removed f rom the
ignition switch, you will hear a
reminder chime when you open the
driver’s door. When the light switch is in the
‘‘ ’’ or ‘‘ ’’ position, the
lights on indicator comes on as a
reminder. This indicator stays on if
you leave the light switch on and
turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position.
To switch f rom low
beams to high beams, push the lef t
lever f orward until you hear a click.
The blue high beam indicator will
come on (see page ). Pull it back
to return to low beams. To flash the
high beams, pull the lever back
lightly, then release it. The high
beamsstayonaslongasyouhold
the lever back.
Turn Signal
Of f
Parking and instrument panel
AUTO
Headlights on
High beams
Flashhighbeams
Fog lights of f
Fog lights on 65
1.
2.
3.
4.
5.
6.
7.
8.
9. Turn Signal
Headlights
High Beams
Turn Signals and Headlights
140
10/08/04 19:04:47 31SJA660_145
ProCarManuals.com

When you turn the ignition switch to
the LOCK (0) position and release it,
or remove the built-in key f rom the
ignition switch, the steering wheel
automatically moves f ully in and up.
Steering wheel movement is also
controlled by the driving position
memory system (see page ).
To change the ‘‘AUTO TILT &
TELESCOPIC’’ setting, see page. If your vehicle’s battery is
disconnected or goes dead, or the
f use f or the power tilt and telescopic
steering wheel is removed, the
power tilt and telescopic steering
wheel system needs to be reset
when you reconnect the battery or
install the f use.
The steering wheel returns to its
original position when you push the
ignition switch or insert the built-in
key back in the ignition switch. Push the ignition switch f or more
than 1 second and release it, or
insert the built-in key into the
ignition switch, and remove it. The
steering wheel automatically moves
f ully in and up to let you know the
system is reset.
106 164
Steering Wheel A djustments
Inst rument s and Cont rols
149
10/08/04 19:06:14 31SJA660_154
ProCarManuals.com

These keys contain electronic
circuits that are activated by the
immobilizer system. They will not
work to start the engine if the
circuits are damaged.Protect the keys f rom direct
sunlight, high temperature, and
high humidity.
Donotdropthekeysorsetheavy
objects on them.
Keep the keys away f rom liquids.
If they get wet, dry them
immediately with a sof t cloth.
The keys do not contain batteries.
Do not try to take them apart.
The built-in key (see page ) f its
all the locks on your vehicle.
Youshouldhavereceivedakey
number tag with your keys. You will
need this key number if you ever
have to get a lost key replaced. Use
only Acura-approved key blanks. The immobilizer system protects
your vehicle f rom thef t. If an
improperly-coded key (or other
device) is used, the engine will not
start.
When you turn the ignition switch to
the ON (II) position, the immobilizer
system indicator should come on
briefly, then go out. If the indicator
starts to blink, it means the system
does not recognize the coding of the
Honda smart key or built-in key.
Turn the ignition switch to the
LOCK (0) position, release the
ignition switch and push it, or
remove the built-in key, and reinsert
it.ThenturntheswitchtotheON
(II) position again.
181
Keys and Locks, Immobilizer System
Keys and Locks
Immobilizer System
150
KEY NUMBER TAG
BUILT-IN KEYS
10/08/04 19:06:26 31SJA660_155
ProCarManuals.com

The system may not recognize your
key’s coding if another immobilizer
key or other metal object (i.e. key
chain) is near the ignition switch
when you turn the ignition switch to
the ON (II) position.
If the system repeatedly does not
recognize the coding of your remote
or built-in key, contact your dealer.
Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your vehicle inoperable.
If you have lost your remote or
built-in key and cannot start the
engine, contact your dealer.The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III).
To use the built-in key, you have to
remove the cover (see page ).
178As required by the FCC:
This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
CONT INUED
Ignition Switch
Immobilizer System, Ignition Switch
Inst rument s and Cont rols
151
IGNITION SWITCH BUILT-IN KEY
COVER
Always take the keyless access remote
and built-in key with you whenever you
leave the vehicle alone.
10/08/04 19:06:40 31SJA660_156
ProCarManuals.com

µµ µ
µ
You can insert or
remove the built-in key only in this
position. To turn the ignition switch
to the LOCK (0) position, the shift
lever must be in Park, and you must
push the knob or built-in key in
slightly.
If the f ront wheels are turned, the
anti-theft lock may make it difficult
to turn the ignition switch. Firmly
turn the steering wheel to the left or
right as you turn the ignition switch.
You can
operate the audio system and the
accessory power sockets in this
position. When you turn the ignition switch to
the ACCESSORY (I) position, an
‘‘ACCESSORY (I) POSITION’’
message is shown on the multi-
inf ormation display.
This is the normal
ignition switch position when driving.
Several of the indicators on the
instrument panel come on as a test
when you turn the ignition switch
f rom the ACCESSORY (I) to the ON
(II) position.
Use this position
only to start the engine. The switch
returns to the ON (II) position when
you let go of the ignition switch. If you open the driver’s door and
leave the ignition switch in the
ACCESSORY (I) or LOCK (0)
position, you will hear a reminder
beeper, and a message appears on
the multi-information display
according to the ignition switch
position. When the ignition switch is
in the ACCESSORY (I) position, a
‘‘RETURNIGNITIONSWITCHTO
LOCK (0) POSITION’’ message is
shown on the multi-inf ormation
display. When the ignition switch is
in the LOCK (0) position, a
‘‘REMOVE KEY’’ message is shown
on the multi-information display.
TheshiftlevermustbeinPark
bef ore you turn the ignition switch
knob to the LOCK (0) position or
remove the built-in key from the
ignition switch.
Ignition Switch
LOCK (0)
A CCESSORY (I)
ON (II)
ST A RT (III)
152
10/08/04 19:06:49 31SJA660_157
ProCarManuals.com