2011.5 PEUGEOT 4007 coolant

1
INSTRUMENTS and CONTROLS
INSTRUMENT PANEINSTRUMENT PANEL

3.
Instrument panel screen:


- Warning and status displays.

- Total and trip distance recorders.

- Service indicator.

- Coolant temperature.

- Trip computer information.

- Cruise control setting.

-
Dashboard lighting and parameter
settings.

- Fuel level.

- Ambient temperature.

- Transmission mode.

Panel grouping together the dials and
warning/indicator lamps. These inform
the driver of the activation/deactivation
of a system or of the occurrence of a
fault.
Screen type 1
Screen type 2


1.
Rev counter.

2.
Speedometer.

1
INSTRUMENTS and CONTROLS





Warning messages (ignition at "ON")



Message



is on



Cause



Solution - action



Observations






ABS
Fixed Anti-lock braking system
(ABS) fault. Contact a PEUGEOT
dealer or a qualifi ed
workshop. The vehicle retains
conventional braking
without assistance but
you are advised to stop.



Braking
system
Fixed

Associated warning lamp.
The level of brake fl uid in
the reservoir is too low. Stop and top up, otherwise
contact a PEUGEOT
dealer or a qualifi ed
workshop. If the message remains on
after topping up, contact
a PEUGEOT dealer or a
qualifi ed workshop.

Associated warning
lamp.
Braking system fault. Contact a PEUGEOT
dealer or a qualifi ed
workshop.
You must stop as
soon as it is safe to
do so.




Parking brake
on
Fixed You have moved off with
the parking brake still
applied. Release the parking brake.




Coolant
temperature
Flashing
High engine
temperature. If the message fl ashes
,
wait for the engine to cool
before topping up the level,
if necessary.
You must stop your
vehicle as soon as it
is safe to do so.


Flashing

If the message fl ashes
and the service warning
light comes on
, contact
a PEUGEOT dealer or
a qualifi ed workshop
without delay.




Seat belt
Fixed The driver has not fastened
or has unfastened his seat
belt. Fasten your seat belt. There is an intermittent
audible signal above
5 mph (8 km/h).

1
INSTRUMENTS and CONTROLS
The total distance is
displayed in zone 1

of the screen and the
trip distance in zone 2

(refer to the "Distance
recorders" section).
Distance recorder (A and B)
INFORMATION IN THINFORMATION IN THE
INSTRUMENT PANEL SCREEN

Information display

With the ignition on, press the INFO

button, located on the dashboard to the
right of the instrument panel, to display
the various information in succession:


- distance recorder A,

- distance recorder B,

- service indicator,

- coolant temperature,

- range,

- trip computer,

- setting menu. This displays the distance
and the number of months
remaining before the
next service in line with
with the manufacturer’s
servicing schedule (refer
to the "Service indicator"
section).
Service indicator
When the engine is
running, this indicates
the temperature of the
coolant (refer to the
"Coolant temperature
indicator" section).
Coolant temperature When the engine is
running, this indicates
the number of miles
(kilometres) which can
still be travelled with the
fuel remaining in the tank
based on the average
fuel consumption over
the last few miles (kilometres) travelled
(refer to the "Range" section).
Range

This indicates the average
fuel consumption, the
average speed and the
current fuel consumption
(refer to the "Trip computer"
section).


Trip computer


When the vehicle is
stationary
, this allows the
user to change the following
settings (refer to the "Setting
menu" section):


- the display language,

- the temperature dis-
play units,

- the fuel consumption units,

- the option to reset the average
fuel consumption and the average
speed,

- the break (rest) reminder display in-
terval.


Setting menu

1
INSTRUMENTS and CONTROLS
The total distance is
displayed in zone 1
of
the screen and the trip
distance in zone 2
.
DISTANCE RECORDERS (A/B)

System for measuring the total distance
travelled by the vehicle during its service
life and the distance travelled in a day
or other period until it is reset to zero by
the driver.

Zero reset

With the ignition on, press the INFO
button for more than 2 seconds until
zeros appear.

When the engine is
running, this indicates
the temperature of the
coolant.
COOLANT TEMPERATURE
If the bar is close to the critical
position
located on the right, the temperature is
too high.
The symbol fl ashes when your engine
is overheating.

You must stop your vehicle as soon
as it is safe to do so.


Wait a few minutes before switching
off the engine.

Wait for the engine to cool before
topping up the level. The cooling
system is pressurised.
When the engine is
running
, this indicates
the distance which can
still be travelled with the
fuel remaining in the tank
based on the average
fuel consumption over
the last few miles/
kilometres travelled.
RANGEGE
When the range is less than 30 miles
(50 km)
, dashes are displayed.
Refuel as soon as possible. The display
of the range is updated.
To avoid any risk of scalding,
unscrew the cap by two turns to
allow the pressure to drop.
When the pressure has dropped, remove the cap and top up the
level, if necessary.
Contact a PEUGEOT dealer or
a qualifi ed workshop. This fi gure may increase
following a change in the style
of driving or the relief, resulting
in a reduction in the current fuel
consumption.
If you only add a few litres, the
value displayed will be incorrect.
Therefore, you must fi ll the tank
whenever possible.
When you disconnect the battery,
the previous fuel consumption
data is lost and the value
displayed will be different from
that displayed before the battery was disconnected. The distance
displayed must be considered
an approximate indication.

8
CHECKS
PETROL ENGINE


1.
Screenwash and headlamp wash
reservoir.

2.
Coolant reservoir.

3.
Power steering fl uid reservoir.

4.
Brake fl uid reservoir.

5.
Fusebox.

6.
Battery.

7.
CVT gearbox dipstick.

8.
Radiator cap.

9.
Engine oil dipstick.

10.
Engine oil fi ller cap.

11 .
Air fi lter. Access for checking the levels of the various fl uids and the replacement of certain components.

8
CHECKS
SEL ENGINEDIESEL EN
Access for checking the levels of the various fl uids and the replacement of certain components.


1.
Coolant reservoir.

2.
Power steering fl uid reservoir.

3.
Screenwash and headlamp wash
reservoir.

4.
Brake fl uid reservoir.

5.
Fusebox.

6.
Battery.

7.
Engine oil dipstick.

8.
Engine oil fi ller cap.

9.
Air fi lter.

8
CHECKS
CHECKING LEVELS
Brake fluid level
To avoid any risk of scalding, unscrew
the cap by two turns to allow the pres-
sure to drop. When the pressure has
dropped, remove the cap and top up
the level.

Oil level

The reading will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
The check is carried out either
when the ignition is switched on using
the oil level indicator on the instrument
panel, or using the dipstick.
It is normal to top up the engine oil between
services. The manufacturer recommends
that the oil level be checked, and topped up
if necessary, every 3 000 miles (5 000 km).
The brake fl uid level should be
between the "MAX" and "MIN"
marks.
If it is not, check the brake pad
wear.

Changing the brake fl uid
Refer to the servicing booklet for details
of the interval for this operation.


Coolant level

The coolant level must be mea-
sured when the engine is cold
and should be between the
"LOW" and "FULL" marks.
When the engine is warm, the
temperature of the coolant is regulated
by the fan. This can operate with the ig-
nition off.
On vehicles which are fi tted with a
particle emission fi lter, the fan may
operate after the vehicle has been
switched off, even if the engine is
cold.
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying
out any work.

Screenwash and headlamp
wash
fluid*

Check the fl uid level regularly,
using the gauge.

*
According to country.
Changing the engine oil
Refer to the servicing booklet for details
of the interval for this operation.
In order to maintain the reliability of the
engine and emission control system,
the use of additives in the engine oil is
prohibited.

Oil specifi cation
The oil must correspond to your engine
and conform to the manufacturer's
recommendations.

Fluid specifi cation
The brake fl uid must conform to the
manufacturer's recommendations and
fulfi l the DOT4 standards.

Changing the coolant fl uid
Refer to the servicing booklet for details
of the interval for this operation.

Fluid specifi cation
The coolant must conform to the manu-
facturer's recommendations.


Fluid specifi cation
This fl uid must conform to the manufac-
turer's recommendations for optimum
cleaning.



Power steering fluid level

Check the fl uid level with the engine at
idle.
Check that the power steering fl uid
level is always between the "MAX" and
"MIN" marks and top up if necessary.

Fluid specifi cation
This fl uid must conform to the manufac-
turer's recommendations.
Check all of these levels regularly and
top them up if necessary, unless other-
wise indicated.
If a level drops signifi cantly, have the
corresponding system checked by a
PEUGEOT dealer or a qualifi ed work-
shop.
When working under the bonnet, take
care as certain areas of the engine may
be extremely hot (risk of burns).

9
PRACTICAL INFORMATION

Direction indicators (1)
Coloured bulbs must be re-
placed with bulbs of identical
specifi cation and colour.

)
Turn the bulb holder A
to the left
and remove it.

)
Pull the bulb and change it.
To r efi t, carry out these operations in
reverse order.
Access to the bulbs on the left-hand
side
When you change a bulb on the left-
hand side, remove the relay box fi xing
nut B
and move the relay box towards
the rear.
Access to the bulbs on the right-
hand side
When you change a bulb on the right-
hand side:


)
Remove the screenwash reservoir
fi xing C
and move the reservoir to-
wards the rear.

)
Remove the coolant reservoir fi xing
nut D
.

)
Remove the clip E
and raise the res-
ervoir moving it towards the front.