2011.5 Citroen C5 RHD bulb
[x] Cancel search: bulbPage 5 of 340
CONTENTS
Direction indicators 116
Hazard warning lamps 116
Horn 116
Emergency or assistance call 116
Tyre under-infl ation detection 117
Braking assistance systems 119
Trajectory control systems 120
Seat belts 121
Airbags 124 „
„
„
„
„
„
„
„
„
VIII - SAFETY 116 Î 127
Parking brake 128
Electric parking brake 129
Hill start assist 136
Manual gearbox 137
Gear shift indicator 138
6-speed electronic
gearbox system 139
Stop & Start 143
Automatic gearbox 146
Fixed centred controls steering
wheel 150
Speed limiter 152
Cruise control 154
Lane departure warning system 156
Parking space sensor 157
Parking sensors 159
"Hydractive III +" electronic
suspension 160
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
IX - DRIVING 128 Î 162
Bonnet 164
Running out of fuel (Diesel) 166
Petrol engines 167
Diesel engines 169
Checking levels 172
Checks 174 „
„
„
„
„
„
X - CHECKS 163 Î 175
Temporary puncture repair kit 176
Changing a wheel 179
Changing a bulb 183
Changing a fuse 193
Battery 198
Energy economy mode 200
Towing the vehicle 201
Towing a trailer 202
Roof bars 203
Very cold protection 204
Cold climate screen 205
Matt paint 206
Accessories 207 „
„
„
„
„
„
„
„
„
„
„
„
„
XI - PRACTICAL
INFORMATION 176 Î 208
Petrol engines 209
Petrol weights 210
Diesel engines 212
Diesel weights 214
Diesel weights - commercial
versions (Tourer) 218
Dimensions 219
Identifi cation markings 223 „
„
„
„
„
„
„
XII - TECHNICAL
DATA 209 Î 224
Emergency or assistance 225
NaviDrive 3D 229
MyWay 273
Audio system 305 „
„
„
„
XIII - AUDIO and
TELEMATICS 225 Î 324
VISUAL
SEARCH 325 Î 330
ALPHABETICAL
INDEX 331 Î 336
Page 93 of 340
V
91
VISIBILITY
Linked with the automatic
"Guide-me-home" lighting
The link with the automatic illumi-
nation of headlamps provides the
"guide-me-home" lighting with the
following additional options:
- selection of the duration of ligh-
ting for 15, 30 or 60 seconds in
the vehicle parameters on the in-
strument panel screen confi gu-
ration menu,
- automatic activation of "guide-
me-home" lighting when auto-
matic illumination of headlamps
is in operation.
Operating fault
In the event of a fault with the sun-
shine sensor, the lighting comes on
and a message appears in the instru-
ment panel screen, accompanied by
an audible signal.
Contact a CITROËN dealer or a
qualifi ed workshop.
In fog or snow, the sunshine sen-
sor may detect suffi cient light.
Therefore, the lighting will not
come on automatically.
Do not cover the sunshine sen-
sor, linked with the rain sensor and
located in the centre of the wind-
screen behind the rear view mirror;
the associated functions would no
longer operate.
MANUAL HEADLAMP
ADJUSTMENT
To avoid dazzling other road users,
the height of the halogen bulb head-
lamps must be adjusted according
to the load in the vehicle.
0.
1 or 2 people in the front seats.
-. 3 people.
1.
5 people.
-. Intermediate setting.
2.
5 people + maximum authorised
loads.
-. Intermediate setting.
3.
Driver + maximum authorised
loads.
Initial setting is position "0"
.
AUTOMATIC ADJUSTMENT
OF DIRECTIONAL
HEADLAMPS
Do not touch the xenon bulbs.
Contact a CITROËN dealer or a
qualifi ed workshop. If a fault occurs, this
warning lamp comes
on in the instrument
panel, accompanied by an audible signal and a
message in the instru-
ment panel screen.
The system then places your head-
lamps in the lowest position. To avoid causing a nuisance to other
road users, this system corrects
the height of the xenon headlamp
beams automatically and when sta-
tionary, depending on the load in the
vehicle.
Page 185 of 340
XI
!
183
PRACTICAL INFORMATION
CHANGING A BULB
Front lamps
Model with Xenon headlamps
(D1S)
1.
Dual-function Xenon
headlamps (dipped/main):
D1S
2.
Cornering lighting:
HP19
3.
Daytime running lamps/
sidelamps (LEDs)
For the maintenance of the front
lamps and changing HP19 and
D1S bulbs and LED lamps, contact
a CITROËN dealer or a qualifi ed
workshop.
Risk of electrocution
Xenon bulbs must be replaced by
a CITROËN dealer or a qualifi ed
workshop.
You are advised to change both
D1S bulbs at the same time, if one
of them has failed. The headlamps are fi tted with
polycarbonate glass with a
protective coating:
)
do not clean them using a
dry or abrasive cloth, nor
with a detergent or solvent
product,
)
use a sponge and soapy water,
)
when using a high pressure
washer on persistent marks, do
not keep the lance directed to-
wards the lamps or their edges
for too long, so as not to dam-
age their protective coating and
seals.
)
Do not touch the bulb directly
with your fi ngers, use lint-free
cloths.
Changing a bulb should only be
done after the headlamp has been
switched off for a few minutes (risk
of serious burns).
It is imperative to use only anti-
ultraviolet (UV) type bulbs in order
not to damage the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specifi cation.
Page 186 of 340
XI
184
PRACTICAL INFORMATION
Main beam headlamps
)
Remove the protective cap A
.
)
Disengage the retaining spring.
)
Remove the bulb and replace it,
paying attention to the direction
of fi tting.
)
Refi t the retaining spring.
)
Refi t the protective cap A
.
Model with halogen headlamps
1.
Main beams:
H1
2.
Dipped beams:
H7
3.
Directional lighting:
H7
4.
Daytime running lamps/
sidelamps (LEDs)
For the maintenance of the front lamps
and changing LED lamps, contact a
CITROËN dealer or a qualifi ed work-
shop.
Sidelamps
Contact a CITROËN dealer or a
qualifi ed workshop.
Page 187 of 340
XI
185
PRACTICAL INFORMATION
Sidelamps
Contact a CITROËN dealer or a
qualifi ed workshop.
Dipped beam headlamps
)
Remove the protective cap B
.
)
Disconnect the connector by
pressing it between the thumb
and index fi nger.
)
Free the bulb from its two metal
clamps.
)
Take out the bulb.
)
Replace the bulb, exerting a
slight axial force.
)
Refi t the connector, until it is all
the way in.
)
Refi t the protective cap B
.
Directional lamp
)
Remove the protective cap C
.
)
Disconnect the connector by
pressing it between the thumb
and index fi nger.
)
Free the bulb from its two metal
clamps.
)
Take out the bulb.
)
Replace the bulb, exerting a
slight axial force.
)
Refi t the connector, until it is all
the way in.
)
Refi t the protective cap C
.
Page 188 of 340
XI
186
PRACTICAL INFORMATION
Front foglamps
)
Remove the fi xing screw of cover A
using a torx tool, tip the cover over
and remove.
)
Remove the fi xing screw of lamp B
using a torx tool and pull the head-
lamp unit to remove it from the
bumper.
)
Disconnect the connector D
.
)
Remove the bulb by performing
a quarter of a turn.
)
Replace the bulb.
)
Refi t the connector D
.
)
Refi t the headlamp unit in the
bumper.
)
Refi t the lamp screws.
)
Position the cover using its guides
and refi t the screws.
Bulbs:
H8
Direction indicators
)
Remove the fi xing screw of cover A
using a torx tool, tip the cover over
and remove.
)
Remove the fi xing screw of lamp B
using a torx tool and pull the head-
lamp unit to remove it from the
bumper.
)
Detach the bulb C
by pressing
on bars 1
and 2
.
)
Disconnect the connector (pull
whilst pressing on the grey
tongue using a fl at screwdriver).
)
Replace the bulb.
)
Refi t the connector (push the
grey tongue in well).
)
Refi t the headlamp unit in the
bumper.
)
Refi t the lamp screws.
)
Position the cover using its
guides and refi t the screws.
Bulbs:
HP24W
Page 189 of 340
XI
187
PRACTICAL INFORMATION
The side repeater is sealed.
If the bulb is faulty, replace the side
repeater.
Contact a CITROËN dealer or a
qualifi ed workshop.
Side repeaters
Rear lamps (Saloon)
Identify the failed bulb.
1.
Brake lamps and sidelamps:
P 21 W/5 W
2.
Sidelamps:
R 5 W
3.
Reversing lamp:
H 21 W
4.
Foglamps:
H 21 W
5.
Direction indicators:
PY 21 W
)
Open the boot.
)
Using a fl at screwdriver, remove
the 3 clips which fi x the trim in
the lamp area.
)
Partially remove the trim F
.
)
Disconnect the connector G
.
Boot-mounted lamps
)
Unclip the bulb holder H
.
)
Replace the bulb.
)
Refi t the bulb holder H
.
)
Check that the bulb holder H
is se-
cured correctly by the two clips 6
.
)
Refi t the connector G
.
)
Replace and fi x the trim F
with its
clips.
When refi tting, take care not to
trap the electrical cables.
Page 190 of 340
XI
188
PRACTICAL INFORMATION
Wing-mounted lamps
)
Remove the lateral boot trim
fl ap A
. To do so, pull it towards
the inside of the boot, then pull it
upwards.
)
Disconnect connector B
.
)
Unscrew the 2 fi xings C
.
)
Remove the lamp from its housing.
)
Detach the bulb holder D
.
)
Replace the bulb.
)
Refi t the bulb holder D
.
)
Place the lamp in its housing.
)
Screw in the 2 fi xings C
.
)
Refi t connector B
.
)
Refi t the trim A
.
You can use the wheelbrace to screw
or unscrew the fi xings C
.