2011.5 Citroen C5 RHD P switch

III
59
COMFORT

Setting the time

Once the time has been displayed,
by means of the buttons 1
, press
buttons 4
and 5
simultaneously with-
in 10 seconds.

Immediate activation

Press button 5
(ON) until the mes-
sage "OK"
appears.
When the signal has been received,
the message "OK"
is displayed
along with the duration of operation. Press the buttons 1
to display the
duration of operation.
This symbol fl ashes.
Set the time using the buttons 1
.
Press buttons 4
and 5
simultaneously
to save it.
This symbol is displayed (fi xed).

The heater starts and this
symbol is displayed.
To deactivate the function, press
button 4
(OFF) until the message
"OK"
appears.
This symbol is switched off.
When carrying out these opera-
tions, if the message "FAIL"
ap-
pears, the signal has not been
received. Repeat the procedure
after changing your location.


Setting the duration
of operation
This symbol is displayed.
Once the duration of operation has
been displayed, press buttons 4
and
5
simultaneously within 10 seconds.
This symbol fl ashes.
Set the duration by pressing the
buttons 1
(adjustment in steps of
10 mins and max value 30 mins).
Press buttons 4
and 5
simultaneously
to save the duration of operation.
This symbol is displayed (fi xed).

The factory setting value is 30 minutes.

III
60
COMFORT

Programming the heating

You must programme your depar-
ture time in order for the system to
calculate the optimum heater start
time automatically.

Programming the departure time
Press the buttons 1
to display the
programming time.
Activation - deactivation
Once the programming time has
been displayed by means of the but-
tons 1
, press button 5
(ON) until the
message "OK"
appears.
This symbol is displayed.
Once the programming time has
been displayed, press buttons 4
and
5
simultaneously within 10 seconds.
This symbol fl ashes.
Set the time by pressing the buttons 1

and press buttons 4
and 5
simultane-
ously to save it.
This symbol is displayed (fi xed).

This symbol is displayed when
the heater starts.
HTM: Heat Thermo Management.

When the signal has been received,
the message "OK"
is displayed along
with the symbol "HTM"
.

To deactivate the programming,
press button 4
(OFF) until the mes-
sage "OK"
appears.

The symbol "HTM"
is switched off.

When carrying out these opera-
tions, if the message "FAIL"
ap-
pears, the signal has not been
received. Repeat the procedure
after changing your location.
Switching off the heating
Press button 5
(ON).

The symbol "HTM"
remains on.


Changing the level of heating
The system offers 5 levels
of heat-
ing (from the lowest level C1
to the
highest level C5
).
Once the level of heating has been
displayed by means of the buttons 1
,
press buttons 4
and 5
simultaneously.
The letter "C"
fl ashes.
Set the level of heating by pressing
the buttons 1
.
Press buttons 4
and 5
simultane-
ously to save the level selected. The
letter "C"
is displayed (fi xed).
The factory pre-sets are replaced
by the new settings entered. The
programmed times are stored until
the next time they are changed.
When the departure time is acti-
vated, the level of heating cannot
be changed. The departure time
must be deactivated fi rst.

III
!
61
COMFORT

Changing the battery
The remote control is supplied by a
6 V-28L battery, which is supplied.
Information on the display indicates
when it is time to replace this battery.
Unclip the casing then replace the
battery.
The remote control must then be
reinitialised, see below.
Always switch off the program-
mable heating while fi lling with
fuel to avoid any risk of fi re or
explosion.
To avoid any risk of poisoning and
asphyxiation, the programmable
heating must not be used, even
for short periods, in an enclosed
space such as a garage or work-
shop which is not equipped with an
exhaust gas extraction system.
Do not park the vehicle on an
infl ammable surface (dry grass,
dead leaves, paper…), there is a
risk of fi re.

The programmable heating system
is supplied by the vehicle's fuel tank.
Before use, ensure that the quantity
of fuel remaining is suffi cient. If the
fuel tank is at the reserve, we strong-
ly advise that you do not programme
the heating.


Do not discard the used
batteries, take them to an
approved collection point.

Reinitialising the remote control
If the vehicle's battery is disconnected
or the remote control's battery is re-
placed, the remote control must be
reinitialised.
After switching on the power, press
button 4
(OFF) for 1 second within
the next 5 seconds. If the operation
has taken place correctly the mes-
sage "OK"
is displayed on the remote
control screen.
If a problem occurs, the message
"FAIL"
appears. Repeat the operation.

In addition, your programmable
heating can be used to pre-heat
your vehicle's passenger com-
partment.
The interior volumetric protection
alarm movement sensor may be
disturbed by the fl ow of air from
the programmable heating when
it is in operation.
To avoid any unexpected trigger-
ing of the alarm during use of the
programmable heating, it is ad-
visable to deactivate the interior
volumetric protection.

III
63
COMFORT








FRONT SEATS
ELECTRIC ADJUSTMENTS

To adjust the electric seats, switch on the ignition or start the engine if the
vehicle has gone into economy mode.
Seat adjustments are also possible for a short period after opening one of the
front doors or switching off the ignition.

2.


Adjustment of the backrest angle


Move the control forwards or
backwards to adjust the backrest
angle.

3.
Adjustment of the angle of the
top of the backrest


Move the control forwards or
backwards to adjust the angle of
the top of the backrest.

1.
Adjustment of the seat height
and angle, and longitudinal
adjustment



)
Raise or lower the front of the
control to adjust the seat cushion
angle.

)
Raise or lower the rear of the
control to raise or lower the seat.

)
Simultaneously raise or lower
the front and rear of the control
in order to raise or lower the
entire seat.
4.
Adjustment of lumbar support


This function allows you to inde-
pendently adjust the height and
level of lumbar support.
Move the control:


)

Forwards or backwards to increase
or reduce the lumbar support.

)
Upwards or downwards to raise or
lower the lumbar support zone.







Head restraint height and
angle adjustments on electric
seats


)
To adjust the angle of the head
restraint, push back or pull for-
ward section C
of the head re-
straint until you reach the desired
position.

)
To raise it, pull upwards.

)
To lower it, press on the control D

to unlock it, and simultaneously
on the head restraint itself.

)
To remove it, press on the
control D
to unlock it, then pull it
upwards.

III
64
COMFORT
This function provides the driver with
a back massage. It only operates
when the engine is running.


)
Press on button A
.
The warning lamp comes on and the
massage function is activated for a
period of 1 hour. During this time,
massage is performed in cycles of
6 minutes (4 minutes of massage fol-
lowed by 2 minutes break). In total,
the system will perform 10 cycles.
After 1 hour, the function is deacti-
vated. The warning lamp goes out.






Massage function




Welcome function

The welcome function assists entry
and leaving the vehicle.
After switching off the ignition and
opening the driver’s door, the seat
moves back automatically and then
stays in this position, ready for the
next entry to the vehicle.
When switching on the ignition, the
seat moves forward to the memo-
rised driving position.
When moving the seat, take care
that no person or object hinders the
automatic movement of the seat.
This function is deactivated by de-
fault. You may activate or deactivate
this function using the "Main Menu"
on the instrument panel screen. To
do so, select "Vehicle parameters/
Comfort/Driver welcome".

Deactivation
You can deactivate the massage
function at any time by pressing on
button A
.











Heated seats control


With the engine running, the front
seats can operate separately.


)
Use the corresponding adjust-
ment dial, placed on the outer
side of each front seat, to switch
on and select the level of heating
required:

0
: Off.

1
: Low.

2
: Medium.

3
: High.

III
65
COMFORT












Storing driving positions

System which stores the settings of
the driver's seat and air conditioning.
Up to two positions can be stored
using the buttons on the side of the
driver's seat.
Storing a position

Using buttons M/1/2


)
Switch on the ignition.

)
Adjust your seat.

)
Press button M
, then press but-
ton 1
or 2
within four seconds.
An audible signal confi rms that the
settings have been stored.
Storing a new position cancels the
previous position.

Recalling a stored position

Ignition on or engine running


)
Briefl y press button 1
or 2
to re-
call the corresponding position.
An audible signal indicates the end
of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery.
For your safety, avoid storing a
driving position while driving.









REAR HEAD RESTRAINTS

The rear head restraints can be
removed and have two positions:


- high, position for use,

- low, storage position.
To raise a head restraint, pull it up-
wards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high posi-
tion, push the lug and pull it upwards.
To r efi t it, engage the head restraint
rods in the holes taking care to re-
main in line with the seat back.
Never drive with the head restraints
removed, they must be in place and
correctly adjusted.

IV
69
ACCESS

















REMOTE CONTROL KEY

System which permits central unlock-
ing or locking of the vehicle using the
lock or from a distance. It is also used
to locate and start the vehicle and
provide guide-me-home lighting, as
well as providing protection against
theft.

Unlocking the vehicle


Complete unlocking using the
remote control

Unfolding the key


)
First press button A
to unfold the
key.


)
Press the open padlock
to unlock the vehicle.


Complete unlocking using the key


)
Turn the key to the left in the
driver's door lock to unlock the
vehicle.
Unlocking is confi rmed by rapid
fl ashing of the direction indicators
for approximately two seconds and
lighting of the courtesy lamp (if the
function is activated).
According to version, the door mirrors
unfold at the same time.



Selective unlocking using
the remote control


)
Press the open pad-
lock once to unlock the
driver's door only.

)
Press the open padlock again to
unlock the other doors and the
boot. According to version, the exterior
mirrors unfold at the same time as
the fi rst unlocking action.
The complete or selective unlocking
parameter is set via the instrument
panel screen confi guration menu (see
"Instruments and controls" section).
Complete unlocking is activated by
default.
Selective unlocking is not possible
using the key.
Each unlocking is confi rmed by
rapid fl ashing of the direction indica-
tors for approximately two seconds
and by switching on of the courtesy
lamp.


Electric boot opening


)
Press button B
to open
the boot.

IV
71
ACCESS


)
First press button A
to fold the
key.









Locating your vehicle



)
Press the closed padlock to lo-
cate your locked vehicle in a car
park.
This is indicated by switching on
of the interior lighting and fl ash-
ing of the direction indicators for a
few seconds.
The vehicle remains locked.







Guide-me-home lighting










Anti-theft protection


Electronic engine immobiliser
The key contains an electronic chip
which has a special code. When the
ignition is switched on, this code
must be recognised in order for
starting to be possible.
This electronic engine immobiliser
locks the engine management sys-
tem a few minutes after the ignition
is switched off and prevents starting
of the engine by anyone who does
not have the key.
In the event of a fault,
you are informed by
illumination of this
warning lamp, an au-
dible signal and a message in the
screen.
In this case, your vehicle does not
start; contact a CITROËN dealer as
soon as possible.


Folding the key
A press on button B
oper-
ates the guide-me-home
lighting (lighting of the side-
lamps, dipped beams and
number plate lamps).
A second press before the end of
the timing cancels the guide-me-
home lighting.
The timed duration can be set via the
"Lighting" menu on the "Main Menu"
of the instrument panel screen.