2010 YAMAHA YZF-R125 stop start

INSTRUMENT AND CONTROL FUNCTIONS
3-5
3
EAU12348
Handlebar switches Left
Right
EAU12360
Pass switch “PASS”
Press this switch to flash the headlight.
EAU12400
Dimmer switch“/”
Set this switch to“” for the high
beam and to“” for the low beam.
EAU12460
Turn signal switch“/”
To signal a right-hand turn, push this
switch to“”. To signal a left-hand
turn, push this switch to“”. When re-
leased, the switch returns to the center
position. To cancel the turn signal
lights, push the switch in after it has re-
turned to the center position.
EAU12500
Horn switch“”
Press this switch to sound the horn.
EAU12660
Engine stop switch“/”
Set this switch to“” before starting
the engine. Set this switch to“” to
stop the engine in case of an emergen-
cy, such as when the vehicle overturns
or when the throttle cable is stuck.
EAU12711
Start switch“”
Push this switch to crank the engine
with the starter. See page 5-1 for start-
ing instructions prior to starting the en-
gine.
1. Pass switch “PA S S”
2. Dimmer switch“/”
3. Turn signal switch“/”
4. Horn switch“”
1. Engine stop switch“/”
2. Start switch“”
U5D7E1E0.book Page 5 Monday, July 13, 2009 11:55 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-12
3
With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is set to “
3. Turn the key on.
4. Shift the transmission into the neutral position.
5. Push the start switch.
Does the engine start?
With the engine still running:
6. Move the sidestand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the sidestand down.
Does the engine stall?
After the engine has stalled:
10. Move the sidestand up.
11. Keep the clutch lever pulled.
12. Push the start switch.
Does the engine start?
The system is OK. The motorcycle can be ridden.The neutral switch may not be working correctly.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
The sidestand switch may not be working correctly.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
The clutch switch may not be working correctly.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
YES NO YES NO YES NO
If a malfunction is noted, have a Yamaha
dealer check the system before riding.
WARNING
”.
U5D7E1E0.book Page 12 Monday, July 13, 2009 11:55 AM

OPERATION AND IMPORTANT RIDING POINTS
5-1
5
EAU15951
Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.
WARNING
EWA10271
Failure to familiarize yourself with
the controls can lead to loss of con-
trol, which could cause an accident
or injury.
EAU45310
TIPThis model is equipped with a lean an-
gle sensor to stop the engine in case of
a turnover. To start the engine after a
turnover, be sure to turn the main
switch to “OFF” and then to “ON”. Fail-
ing to do so will prevent the engine from
starting even though the engine will
crank when pushing the start switch.
EAUM2322
Starting the engine In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:

The transmission is in the neutral
position.


The transmission is in gear with
the clutch lever pulled and the sid-
estand up.
See page 3-11 for more informa-
tion.
1. Turn the key to “ON” and make
sure that the engine stop switch is
set to“”.
The following warning lights and
indicator light should come on for a
few seconds, then go off.

Neutral indicator light


Turn signal indicator light


High beam indicator light


Coolant temperature warning
light


Engine trouble warning light
U5D7E1E0.book Page 1 Monday, July 13, 2009 11:55 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-39
6Engine overheating
WARNING
EWA10400


Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.


After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hissing
sound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
TIPIf coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant
as soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
U5D7E1E0.book Page 39 Monday, July 13, 2009 11:55 AM

INDEXAAir filter element and check hose,
replacing and cleaning........................ 6-15
Auxiliary light bulb, replacing ................ 6-33BBattery................................................... 6-29
Brake and clutch levers, checking and
lubricating ........................................... 6-27
Brake and shift pedals, checking and
lubricating ........................................... 6-26
Brake fluid, changing ............................ 6-23
Brake fluid level, checking .................... 6-22
Brake lever .............................................. 3-6
Brake pedal ............................................. 3-7
Brake pedal free play, adjusting............ 6-21CCables, checking and lubricating .......... 6-25
Care ........................................................ 7-1
Catalytic converters ................................ 3-9
Clutch lever ............................................. 3-6
Clutch lever free play, adjusting ............ 6-20
Coolant.................................................. 6-13
Coolant temperature warning light .......... 3-2
Cowlings and panel, removing and
installing................................................ 6-7DDimmer switch ........................................ 3-5
Drive chain, cleaning and lubricating .... 6-25
Drive chain slack ................................... 6-23EEngine break-in ....................................... 5-3
Engine idling speed............................... 6-15
Engine oil and oil filter element ............. 6-10
Engine stop switch .................................. 3-5Engine trouble warning light ................... 3-3
FFront and rear brake pads, checking .... 6-21
Front brake lever free play, checking ... 6-21
Front fork, checking .............................. 6-28
Fuel......................................................... 3-8
Fuel consumption, tips for reducing........ 5-3
Fuel tank cap .......................................... 3-7
Fuses, replacing ................................... 6-31HHandlebar switches ................................ 3-5
Headlight bulb, replacing ...................... 6-32
High beam indicator light ........................ 3-2
Horn switch ............................................. 3-5IIdentification numbers ............................ 9-1
Ignition circuit cut-off system ................ 3-11
Indicator and warning lights .................... 3-2KKey identification number ....................... 9-1LLicense plate light bulb, replacing ........ 6-33MMain switch/steering lock........................ 3-1
Maintenance and lubrication, periodic .... 6-3
Maintenance, emission control system... 6-2
Matte color, caution ................................ 7-1
Model label ............................................. 9-2
Multi-function display .............................. 3-3NNeutral indicator light .............................. 3-2PParking ................................................... 5-4
Part locations .......................................... 2-1Pass switch ............................................. 3-5
RRider seat .............................................. 3-10SSafety information ................................... 1-1
Shifting .................................................... 5-2
Shift pedal ............................................... 3-6
Sidestand .............................................. 3-10
Sidestand, checking and lubricating...... 6-27
Spark plug, checking ............................... 6-9
Specifications .......................................... 8-1
Starting the engine .................................. 5-1
Start switch.............................................. 3-5
Steering, checking................................. 6-29
Storage.................................................... 7-3
Supporting the motorcycle .................... 6-33
Swingarm pivots, lubricating ................. 6-28TTachometer ............................................. 3-3
Tail/brake light ....................................... 6-32
Throttle cable free play, adjusting ......... 6-16
Throttle grip and cable, checking and
lubricating ........................................... 6-26
Tires ...................................................... 6-17
Tool kit..................................................... 6-1
Troubleshooting .................................... 6-37
Troubleshooting charts.......................... 6-38
Turn signal indicator light ........................ 3-2
Turn signal light bulb, replacing ............ 6-32
Turn signal switch ................................... 3-5VValve clearance..................................... 6-17
Vehicle identification number .................. 9-1
U5D7E1E0.book Page 1 Monday, July 13, 2009 11:55 AM