2010 YAMAHA TDM 900 drain bolt

[x] Cancel search: drain bolt

change wheel oil temperature air conditioning OBD port hood open turn signal

Page 12 of 96

YAMAHA TDM 900 2010 Owners Manual
2-1
1
2

DESCRIPTION
EAU32220
Left view
TDM900
12
345678
9 10 11 12 13 1412
345678
9 10 11 12 13 14

1. Front fork spring preload adjusting bolt (page 3-18)
2. Front fork damping adjusting sc

Page 13 of 96

YAMAHA TDM 900 2010 Owners Manual
DESCRIPTION
2-2
2
3
4
5
6
7
8
9 TDM900A
12
3456
7 8 9 10 11 1212
3456

1. Front fork spring preload adjusting bolt (page 3-18)
2. Front fork damping adjusting screw (page 3-18)
3. Air ﬁlter ele

Page 14 of 96

YAMAHA TDM 900 2010 Owners Manual
DESCRIPTION
2-3
1
2
3
4
5
6
7
8
9

EAU32230
Right view
TDM900
1234
5
6 7 8 9 10

1. Owner’s tool kit (page 6-1)
2. Coolant reservoir (page 6-12)
3. Idle adjusting screw (page 6-16)
4. Front

Page 15 of 96

YAMAHA TDM 900 2010 Owners Manual
DESCRIPTION
2-4
2
3
4
5
6
7
8
9 TDM900A
1
56
7
8 9 10 11 12
23 4

1. Grab bar
2. Owner’s tool kit (page 6-1)
3. Storage compartment (page 3-17)
4. Shock absorber assembly compression damping fo

Page 56 of 96

YAMAHA TDM 900 2010 Owners Manual
PERIODIC MAINTENANCE AND ADJUSTMENT
6-10
1
2
3
4
5
6
7
8
9spout out and cause damage or
injury. Always let the engine oil
cool down sufficiently before re-
moving the oil tank cap.

[EWA10361]
N

Page 57 of 96

YAMAHA TDM 900 2010 Owners Manual
PERIODIC MAINTENANCE AND ADJUSTMENT
6-11
2
3
4
5
67
8
9
TIP

Skip steps 5–7 if the oil filter element is
not being replaced.
5. Remove the oil filter element cover
by removing the bolts.6. Rem

Page 58 of 96

YAMAHA TDM 900 2010 Owners Manual
PERIODIC MAINTENANCE AND ADJUSTMENT
6-12
1
2
3
4
5
6
7
8
9
9. Refill with the specified amount of
the recommended engine oil, and
then install and tighten the oil filler
cap.
TIP

Be sure to wip

PERIODIC MAINTENANCE AND ADJUSTMENT
6-12
1
2
3
4
5
6
7
8
9
9. Refill with the specified amount of
the recommended engine oil, and
then install and tighten the oil filler
cap.
TIP

Be sure to wipe off spilled oil on any
parts after the engine and exhaust sys-
tem have cooled down.
NOTICE

ECA11620

In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Donot use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.

Make sure that no foreign mate-
rial enters the crankcase.
10. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
11. Turn the engine off, and then
check the oil level and correct it if
necessary.
EAU20070
Coolant
The coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAU38583
To check the coolant level
1. Place the vehicle on a level sur-
face and hold it in an upright posi-
tion.
TIP

The coolant level must be checked
on a cold engine since the level
varies with engine temperature.

Make sure that the vehicle is posi-
tioned straight up when checking
the coolant level. A slight tilt to the
side can result in a false reading.
2. Check the coolant level in the cool-
ant reservoir.
TIP

The coolant should be between the
minimum and maximum level marks.
Tightening torques:
Engine oil drain bolt A:
35 Nm (3.5 m·kgf, 25 ft·lbf)
Engine oil drain bolt B:
30 Nm (3.0 m·kgf, 21.7 ft·lbf)
Recommended engine oil:
See page 8-1.
Oil quantity:
Without oil filter element replace-
ment:
3.80 L (4.02 US qt, 3.34 Imp.qt)
With oil filter element replacement:
3.90 L (4.12 US qt, 3.43 Imp.qt)
✼✥✯✣✲ ✤✥

radio controls fuel additives height adjustment spark plugs diagnostic menu alternator belt