2010 YAMAHA TDM 900 coolant

PERIODIC MAINTENANCE AND ADJUSTMENT
6-13
2
3
4
5
67
8
9 For TDM900
For TDM900A
3. If the coolant is at or below the
minimum level mark, remove pan-
el B for TDM900 or panel A for
TDM900A (See page 6-7.), re-
move the reservoir cap, add cool-
ant to the maximum level mark,
and then install the reservoir cap
and the panel.
WARNING! Re-
move only the coolant reservoir
cap. Never attempt to remove
the radiator cap when the en-
gine is hot.

[EWA15161]

NOTICE:
If
coolant is not available, use dis-
tilled water or soft tap water in-
stead. Do not use hard water or
salt water since it is harmful to
the engine. If water has been
used instead of coolant, replace
it with coolant as soon as possi-
ble, otherwise the cooling sys-
tem will not be protected against
frost and corrosion. If water has
been added to the coolant, have
a Yamaha dealer check the anti-
freeze content of the coolant as
soon as possible, otherwise the
effectiveness of the coolant will
be reduced.
[ECA10472]

For TDM900
For TDM900A
1. Coolant reservoir
2. Maximum level mark
3. Minimum level mark
1. Maximum level mark
2. Coolant reservoir
3. Minimum level mark
1 2
33 1
2

1. Coolant reservoir cap
1. Coolant reservoir cap
Coolant reservoir capacity (up to the
maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
1
1
✼✥✯✣✲ ✤✦ 




PERIODIC MAINTENANCE AND ADJUSTMENT
6-37
2
3
4
5
67
8
9 Engine overheating
WARNING

EWA10400

Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.

After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hissing
sound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
TIP

If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant
as soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
✼✥✯✣✲ ✦✪ 




8-1
1
2
3
4
5
6
7
8
9

SPECIFICATIONS
EAU2633X
Dimensions:
Overall length:
2180 mm (85.8 in)
Overall width:
800 mm (31.5 in)
Overall height:
1290 mm (50.8 in)
Seat height:
825 mm (32.5 in)
Wheelbase:
1485 mm (58.5 in)
Ground clearance:
160 mm (6.30 in)
Minimum turning radius:
2900 mm (114.2 in)
Weight:
With oil and fuel:
TDM900 223.0 kg (492 lb)
TDM900A 226.0 kg (498 lb)
Engine:
Engine type:
Liquid cooled 4-stroke, DOHC
Cylinder arrangement:
Forward-inclined parallel 2-cylinder
Displacement:
897 cm
3

Bore
×
stroke:
92.0
×
67.5 mm (3.62
×
2.66 in)
Compression ratio:
10.40 :1
Starting system:
Electric starter
Lubrication system:
Dry sump

Engine oil:
Recommended brand:
YAMALUBE
Type:
SAE 10W-30, 10W-40, 10W-50, 15W-40,
20W-40 or 20W-50
Recommended engine oil grade:
API service SG type or higher, JASO stan-
dard MA
Engine oil quantity:
Without oil filter element replacement:
3.80 L (4.02 US qt, 3.34 Imp.qt)
With oil filter element replacement:
3.90 L (4.12 US qt, 3.43 Imp.qt)
Cooling system:
Coolant reservoir capacity (up to the maxi-
mum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator capacity (including all routes):
1.75 L (1.85 US qt, 1.54 Imp.qt)
Air filter:
Air filter element:
Oil-coated paper element
Fuel:
Recommended fuel:
Regular unleaded gasoline only
Fuel tank capacity:
20.0 L (5.28 US gal, 4.40 Imp.gal)
Fuel reserve amount:
3.5 L (0.92 US gal, 0.77 Imp.gal)
Fuel injection:
Throttle body:
ID mark:
5PSC 30
Spark plug (s):
Manufacturer/model:
NGK/DPR8EA-9
Manufacturer/model:
DENSO/X24EPR-U9
Spark plug gap:
0.8–0.9 mm (0.031–0.035 in)
Clutch:
Clutch type:
Wet, multiple-disc
Transmission:
Primary reduction system:
Spur gear
Primary reduction ratio:
67/39 (1.718)
Secondary reduction system:
Chain drive
Secondary reduction ratio:
42/16 (2.625)
-20 -10 0
10 20 30
40
50 ˚C
SAE 10W-30
SAE 15W-40SAE 20W-40SAE 20W-50
SAE 10W-40SAE 10W-50
✼✥✯✣✲ ✤ 




INDEX
A
ABS (for ABS models) ............................ 3-12
ABS warning light (for ABS models) ......... 3-5
Air filter element, replacing ..................... 6-14
Anti-theft alarm (optional).......................... 3-9
Auxiliary light bulb, replacing .................. 6-34
B
Battery..................................................... 6-29
Brake and clutch levers, checking and
lubricating ............................................. 6-26
Brake and shift pedals, checking and
lubricating ............................................. 6-26
Brake fluid, changing .............................. 6-23
Brake fluid level, checking ...................... 6-22
Brake lever .............................................. 3-11
Brake light switches ................................ 6-21
Brake pedal ............................................. 3-12
C
Cables, checking and lubricating ............ 6-25
Care .......................................................... 7-1
Catalytic converters ................................ 3-16
Clutch lever ............................................. 3-11
Clutch lever free play, adjusting .............. 6-20
Coolant.................................................... 6-12
Coolant temperature gauge ...................... 3-7
Cowlings and panels, removing and
installing.................................................. 6-7
D
Dimmer switch ........................................ 3-10
Drive chain, cleaning and lubricating ...... 6-25
Drive chain slack ..................................... 6-23
E
Engine break-in ......................................... 5-3
Engine idling speed................................. 6-16Engine oil and oil filter element.................. 6-9
Engine stop switch................................... 3-10
Engine trouble warning light ...................... 3-5
F
Front and rear brake pads, checking ....... 6-21
Front fork, adjusting ................................. 3-18
Front fork, checking ................................. 6-27
Fuel.......................................................... 3-14
Fuel consumption, tips for reducing........... 5-3
Fuel level warning indicator ....................... 3-5
Fuel tank breather/overflow hose ............ 3-15
Fuel tank cap ........................................... 3-13
Fuses, replacing ...................................... 6-30
H
Handlebar switches ................................... 3-9
Hazard switch .......................................... 3-10
Headlight bulb, replacing ......................... 6-32
High beam indicator light ........................... 3-4
Horn switch .............................................. 3-10
I
Identification numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-22
Immobilizer system .................................... 3-1
Immobilizer system indicator light.............. 3-5
Indicator and warning lights ....................... 3-4
L
Luggage strap holders ............................. 3-21
M
Main switch/steering lock........................... 3-2
Maintenance and lubrication, periodic ....... 6-3
Maintenance, emission control system...... 6-2
Matte color, caution ................................... 7-1
Model label ................................................ 9-1
Multi-function display ................................. 3-8
N
Neutral indicator light ................................ 3-4
O
Oil level warning light ................................ 3-4
P
Parking ...................................................... 5-4
Part locations ............................................ 2-1
Pass switch ............................................. 3-10
R
Rear suspension, lubricating ................... 6-27
S
Safety information ..................................... 1-1
Seat ......................................................... 3-16
Shifting ...................................................... 5-2
Shift pedal ............................................... 3-11
Shock absorber assembly, adjusting ...... 3-19
Sidestand ................................................ 3-21
Sidestand, checking and lubricating........ 6-27
Spark plugs, checking ............................... 6-8
Specifications ............................................ 8-1
Starting the engine .................................... 5-1
Start switch .............................................. 3-10
Steering, checking................................... 6-28
Storage...................................................... 7-3
Storage compartment.............................. 3-17
Supporting the motorcycle ...................... 6-34
T
Tachometer unit ........................................ 3-6
Tail/brake light bulb, replacing ................ 6-33
Throttle cable free play, checking ........... 6-16
Throttle grip and cable, checking and
lubricating.............................................. 6-26
Tires ........................................................ 6-17
Tool kit....................................................... 6-1
✼✥✯✣✲ ✥