2010 YAMAHA PW80 ABS

TABLE OF CONTENTS
LOCATION OF IMPORTANT
LABELS
............................................. 1-1
SAFETY INFORMATION
.................. 2-1
DESCRIPTION
.................................. 3-1
Left view .......................................... 3-1
Right view ........................................ 3-2
Controls and instruments ................ 3-3
INSTRUMENT AND CONTROL
FUNCTIONS
....................................... 4-1
Handlebar switch ............................ 4-1
Power reduction plate ..................... 4-1
Shift pedal ...................................... 4-1
Brake lever ..................................... 4-2
Brake pedal .................................... 4-2
Fuel tank cap .................................. 4-2
Fuel ................................................ 4-3
Fuel tank breather hose ................. 4-4
2-stroke engine oil .......................... 4-4
Fuel cock ........................................ 4-5
Starter (choke) lever “ ” ................ 4-6
Kickstarter ...................................... 4-6
Seat ................................................ 4-7
Shock absorber assembly .............. 4-7
Sidestand ....................................... 4-8
FOR YOUR SAFETY –
PRE-OPERATION CHECKS
.............. 5-1
OPERATION AND IMPORTANT
RIDING POINTS
................................. 6-1
Starting and warming up a cold
engine ......................................... 6-1
Starting a warm engine .................. 6-2
Shifting ........................................... 6-2
Engine break-in .............................. 6-3
Parking ........................................... 6-4
PPERIODIC MAINTENANCE AND
ADJUSTMENT
................................... 7-1
Owner’s tool kit ............................... 7-1
Periodic maintenance and
lubrication chart .......................... 7-2
Checking the spark plug ................. 7-5
Removing the power reduction
plate ............................................ 7-6
Transmission oil ............................. 7-7
Cleaning the air filter element ........ 7-8
Cleaning the spark arrester ............ 7-9
Adjusting the carburetor ............... 7-10
Adjusting the engine idling
speed ........................................ 7-10
Adjusting the throttle cable free
play ........................................... 7-11
Tires ............................................. 7-12
Spoke wheels ............................... 7-13
Adjusting the brake lever free
play ........................................... 7-13
Adjusting the brake pedal free
play ........................................... 7-14Checking the front and rear
brake shoes ............................... 7-15
Drive chain slack ........................... 7-16
Cleaning and lubricating the
drive chain ................................. 7-17
Checking and lubricating the
cables ........................................ 7-18
Checking and lubricating the
throttle grip and cable ................ 7-18
Adjusting the Autolube pump ........ 7-18
Checking and lubricating the
brake lever ................................. 7-19
Checking and lubricating the
brake pedal ................................ 7-19
Checking and lubricating the
sidestand ................................... 7-19
Checking the front fork .................. 7-20
Checking the steering ................... 7-20
Checking the wheel bearings ........ 7-21
Supporting the motorcycle ............ 7-21
Front wheel ................................... 7-22
Rear wheel .................................... 7-24
Troubleshooting ............................ 7-26
Troubleshooting chart ................... 7-27
MOTORCYCLE CARE AND
STORAGE
.......................................... 8-1
Matte color caution ......................... 8-1
Care ................................................ 8-1
Storage ........................................... 8-3

INSTRUMENT AND CONTROL FUNCTIONS
4-7
2
3
45
6
7
8
9

EAU41140
Seat
To remove the seat
Remove the nuts, and then pull the seat
off.
To install the seat
1. Insert the projection on the front of
the seat into the seat holder as
shown.2. Place the seat in the original posi-
tion, and then tighten the nuts.
TIP

Make sure that the seat is properly se-
cured before riding.
EAU46021
Shock absorber assembly
WARNING

EWA10221
This shock absorber assembly con-
tains highly pressurized nitrogen
gas. Read and understand the fol-
lowing information before handling
the shock absorber assembly.

Do not tamper with or attempt to
open the cylinder assembly.

Do not subject the shock ab-
sorber assembly to an open
flame or other high heat source.
This may cause the unit to ex-
plode due to excessive gas
pressure.

Do not deform or damage the
cylinder in any way. Cylinder
damage will result in poor
damping performance.

Do not dispose of a damaged or
worn-out shock absorber as-
sembly yourself. Take the shock
absorber assembly to a Yamaha
dealer for any service.
1. Nut
1

1. Seat holder
2. Projection
2
1

PERIODIC MAINTENANCE AND ADJUSTMENT
7-3
2
3
4
5
6
78
9
8*Tires
Check tread depth and for damage.Replace if necessary.Check air pressure.Correct if necessary.
9*Wheel bearingsCheck bearings for smooth operation.Replace if necessary.
10 *Steering bearingsCheck bearing assemblies for looseness.Moderately repack with lithium-soap-based
grease.
11Drive chainCheck chain slack/alignment and condi-
tion.Adjust and lubricate chain with Yamaha
chain and cable lube thoroughly.Every rideRemove and clean.
12 *Chassis fastenersCheck all chassis fitting and fasteners.Replace if necessary.
13
Sidestand pivotCheck operation.Apply lithium-soap-based g
rease lightly.
14 *Front fork
Check operation and for oil leakage.Replace if necessary.
15 *Shock absorber
assemblyCheck operation and for oil leakage.Replace if necessary.
16 *CarburetorCheck engine idling speed and starter
operation.Clean.Replace if necessary. NO. ITEM CHECK OR MAINTENANCE JOBINITIAL THEREAFTER EVERY
10
hours20
hours40
hours80
hours40
hours80
hours160
hours

MOTORCYCLE CARE AND STORAGE
8-2
2
3
4
5
6
7
89 off any detergent residue using
plenty of water, as it is harmful
to plastic parts.


Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.

Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.

For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leavescratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain or near the seaSince sea salt is extremely corrosive,
carry out the following steps after each
ride in the rain or near the sea.
1. Clean the motorcycle with cold wa-
ter and a mild detergent, after the
engine has cooled down.
NOTICE:
Do not use warm water
since it increases the corrosiveaction of the salt.

[ECA10791]

2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning
1. Dry the motorcycle with a chamois
or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stain-
less-steel parts, including the ex-
haust system. (Even the thermally
induced discoloring of stain-
less-steel exhaust systems can be
removed through polishing.)
4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
5. Use spray oil as a universal clean-
er to remove any remaining dirt.
6. Touch up minor paint damage
caused by stones, etc.

SPECIFICATIONS
9-2
2
3
4
5
6
7
8
9

26.00 °
Trail:
62.0 mm (2.44 in)
Front tire:
Type:
With tube
Size:
2.50-14 4PR
Manufacturer/model:
CHENG SHIN/KNOBBY
Rear tire:
Type:
With tube
Size:
3.00-12 4PR
Manufacturer/model:
CHENG SHIN/KNOBBY
Loading:
Maximum rider weight:
40.0 kg (88 lb)
Tire air pressure (measured on cold
tires):
Front:
100 kPa (1.00 kgf/cm
2

, 15 psi)
Rear:
100 kPa (1.00 kgf/cm
2

, 15 psi)
Front wheel:
Wheel type:
Spoke wheel
Rim size:
14x1.40
Rear wheel:
Wheel type:
Spoke wheel
Rim size:
12x1.60
Front brake:
Type:
Drum brake
Operation:
Right hand operation
Rear brake:
Type:
Drum brake
Operation:
Right foot operation
Front suspension:
Type:
Telescopic fork
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
110.0 mm (4.33 in)
Rear suspension:
Type:
Swingarm (monocross)
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel:
95.0 mm (3.74 in)
Electrical system:
Ignition system:
CDI

INDEX
A
Air filter element, cleaning ......................... 7-8
Autolube pump, adjusting ........................ 7-19
B
Brake lever ................................................ 4-2
Brake lever, checking and lubricating ...... 7-19
Brake lever free play, adjusting ............... 7-14
Brake pedal ............................................... 4-2
Brake pedal, checking and lubricating ..... 7-19
Brake pedal free play, adjusting .............. 7-15
Brake shoes, checking ............................ 7-15
C
Cables, checking and lubricating ............. 7-18
Carburetor, adjusting ............................... 7-10
Care ........................................................... 8-1
D
Drive chain, cleaning and lubricating ....... 7-18
Drive chain slack ..................................... 7-16
E
Engine break-in ......................................... 6-3
Engine idling speed ................................. 7-11
Engine oil ................................................... 4-4
Engine, starting a warm ............................. 6-2
Engine stop switch..................................... 4-1
F
Front fork, checking ................................. 7-20
Fuel............................................................ 4-3
Fuel cock ................................................... 4-5
Fuel tank breather hose............................. 4-4
Fuel tank cap ............................................. 4-2
H
Handlebar switch ....................................... 4-1
I
Identification numbers ............................. 10-1
K
Kickstarter ................................................. 4-6
L
Labels, location ......................................... 1-1
M
Matte color, caution ................................... 8-1
Model label .............................................. 10-1
P
Parking ...................................................... 6-4
Part locations............................................. 3-1
Periodic maintenance and lubrication
chart ........................................................ 7-2
Power reduction plate................................ 4-1
Power reduction plate, removing ............... 7-6
S
Safety information ..................................... 2-1
Seat ........................................................... 4-7
Shifting ...................................................... 6-2
Shift pedal ................................................. 4-1
Shock absorber assembly ......................... 4-7
Sidestand .................................................. 4-8
Sidestand, checking and lubricating ........ 7-20
Spark arrester, cleaning ............................ 7-9
Spark plug, checking ................................. 7-5
Specifications ............................................ 9-1
Starter (choke) lever .................................. 4-6
Starting and warming up a cold engine ..... 6-1
Steering, checking ................................... 7-21
Storage ...................................................... 8-3
Supporting the motorcycle....................... 7-22
T
Throttle cable free play, adjusting ........... 7-11Throttle grip and cable, checking and
lubricating ............................................. 7-18
Tires ........................................................ 7-12
Tool kit ...................................................... 7-1
Transmission oil ........................................ 7-7
Troubleshooting ...................................... 7-26
Troubleshooting chart ............................. 7-28
V
Vehicle identification number .................. 10-1
W
Wheel bearings, checking ....................... 7-21
Wheel (front) ........................................... 7-22
Wheel (rear) ............................................ 7-25
Wheels .................................................... 7-13