MOTORCYCLE CARE AND STORAGE
8-4
2
3
4
5
6
7
89
“OFF”.
3. Drain the carburetor float chamber
by loosening the drain bolt; this will
prevent fuel deposits from building
up. Pour the drained fuel into the
fuel tank.
4. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
5. Perform the following steps to pro-
tect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug, and theninstall the spark plug and the
spark plug cap.
WARNING! To
prevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.
[EWA10951]
6. Lubricate all control cables and the
pivoting points of all levers and
pedals as well as of the sidestand.
7. Check and, if necessary, correct
the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
8. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
TIP
Make any necessary repairs before
storing the motorcycle.
9-1
1
2
3
4
5
6
7
8
9
SPECIFICATIONS
EAU2633X
Dimensions:
Overall length:
1540 mm (60.6 in)
Overall width:
640 mm (25.2 in)
Overall height:
880 mm (34.6 in)
Seat height:
635 mm (25.0 in)
Wheelbase:
1055 mm (41.5 in)
Ground clearance:
185 mm (7.28 in)
Minimum turning radius:
1700 mm (66.9 in)
Weight:
With oil and fuel:
61.0 kg (134 lb)
Noise and vibration level:
Noise level (77/311/EEC):
PW80 79.3 dB(A)
Vibration on seat (EN1032, ISO5008):
PW80 Will not exceed 0.5 m/s
2
Vibration on handlebar (EN1032, ISO5008):
PW80 Will not exceed 2.5 m/s
2
Engine:
Engine type:
Air cooled 2-stroke
Cylinder arrangement:
Forward-inclined single cylinder
Displacement:
79 cm
3
Bore
×
stroke:
47.0
×
45.6 mm (1.85
×
1.80 in)Compression ratio:
6.60 :1
Starting system:
Kickstarter
Lubrication system:
Separate lubrication (Yamaha autolube)
Engine oil:
Type:
YAMALUBE 2 or 2-stroke engine oil (JASO
FC grade) or (ISO EG-C or EG-D grade)
Engine oil quantity:
Quantity:
0.75 L (0.79 US qt, 0.66 Imp.qt)
Transmission oil:
Type:
YAMALUBE 4 (10W-40) or SAE 10W-40
Oil change quantity:
0.65 L (0.69 US qt, 0.57 Imp.qt)
Air filter:
Air filter element:
Wet element
Fuel:
Recommended fuel:
PW80 Regular unleaded gasoline only
PW80Z Unleaded gasoline only
Fuel tank capacity:
4.9 L (1.29 US gal, 1.08 Imp.gal)
Fuel reserve amount:
1.0 L (0.26 US gal, 0.22 Imp.gal)
Carburetor:
Type
×
quantity:
VM15SC x 1
Spark plug (s):
Manufacturer/model:
PW80
NGK/BPR6HS
PW80Z NGK/BP6HS
DENSO/W20FP
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
Clutch:
Clutch type:
Wet, multiple-disc automatic
Transmission:
Primary reduction system:
Helical gear
Primary reduction ratio:
66/21 (3.143)
Secondary reduction system:
Chain drive
Secondary reduction ratio:
32/15 (2.133)
Transmission type:
Constant mesh 3-speed
Operation:
Left foot operation
Gear ratio:
1st:
39/12 (3.250)
2nd:
29/16 (1.812)
3rd:
22/17 (1.294)
Chassis:
Frame type:
Steel tube backbone
Caster angle:
INDEX
A
Air filter element, cleaning ......................... 7-8
Autolube pump, adjusting ........................ 7-19
B
Brake lever ................................................ 4-2
Brake lever, checking and lubricating ...... 7-19
Brake lever free play, adjusting ............... 7-14
Brake pedal ............................................... 4-2
Brake pedal, checking and lubricating ..... 7-19
Brake pedal free play, adjusting .............. 7-15
Brake shoes, checking ............................ 7-15
C
Cables, checking and lubricating ............. 7-18
Carburetor, adjusting ............................... 7-10
Care ........................................................... 8-1
D
Drive chain, cleaning and lubricating ....... 7-18
Drive chain slack ..................................... 7-16
E
Engine break-in ......................................... 6-3
Engine idling speed ................................. 7-11
Engine oil ................................................... 4-4
Engine, starting a warm ............................. 6-2
Engine stop switch..................................... 4-1
F
Front fork, checking ................................. 7-20
Fuel............................................................ 4-3
Fuel cock ................................................... 4-5
Fuel tank breather hose............................. 4-4
Fuel tank cap ............................................. 4-2
H
Handlebar switch ....................................... 4-1
I
Identification numbers ............................. 10-1
K
Kickstarter ................................................. 4-6
L
Labels, location ......................................... 1-1
M
Matte color, caution ................................... 8-1
Model label .............................................. 10-1
P
Parking ...................................................... 6-4
Part locations............................................. 3-1
Periodic maintenance and lubrication
chart ........................................................ 7-2
Power reduction plate................................ 4-1
Power reduction plate, removing ............... 7-6
S
Safety information ..................................... 2-1
Seat ........................................................... 4-7
Shifting ...................................................... 6-2
Shift pedal ................................................. 4-1
Shock absorber assembly ......................... 4-7
Sidestand .................................................. 4-8
Sidestand, checking and lubricating ........ 7-20
Spark arrester, cleaning ............................ 7-9
Spark plug, checking ................................. 7-5
Specifications ............................................ 9-1
Starter (choke) lever .................................. 4-6
Starting and warming up a cold engine ..... 6-1
Steering, checking ................................... 7-21
Storage ...................................................... 8-3
Supporting the motorcycle....................... 7-22
T
Throttle cable free play, adjusting ........... 7-11Throttle grip and cable, checking and
lubricating ............................................. 7-18
Tires ........................................................ 7-12
Tool kit ...................................................... 7-1
Transmission oil ........................................ 7-7
Troubleshooting ...................................... 7-26
Troubleshooting chart ............................. 7-28
V
Vehicle identification number .................. 10-1
W
Wheel bearings, checking ....................... 7-21
Wheel (front) ........................................... 7-22
Wheel (rear) ............................................ 7-25
Wheels .................................................... 7-13
