2010 YAMAHA PW50 Speed limiter

INTRODUCTION
AN IMPORTANT NOTE TO PARENTS:
This motorcycle is not a toy. Before you let your child ride this motorcycle, you should understand the instructions and warn-
ings in this Owner’s Manual. Then be sure your child understands and will follow them. Children differ in skills, physical abil-
ities, and judgment. Some children may not be able to operate a motorcycle safely. Parents should supervise their child’s
use of the motorcycle at all times. Parents should permit continued use only if they determine that the child has the ability to
operate the motorcycle safely.
Your motorcycle was delivered with an adjustable speed limiter and power reduction plate. Yamaha recommends that all
beginners start off with the speed limiter adjusting screw turned in and the power reduction plate installed in the exhaust man-
ifold to limit the power available while they learn. The limiter screw may be gradually turned out to increase maximum speed
as the beginner becomes more familiar with operating the motorcycle. Parents should decide when to adjust the motorcycle
for more power as their youngster’s riding skills improve. Once the rider can operate with skill at the top speed permitted by
adjusting the speed limiter alone, the power reduction plate can be removed. Since removal of this plate will result in a sig-
nificant increase in power, turn the speed limiter back in again; adjust it out in stages as you did before.
Motorcycles are single track vehicles. Their safe use and operation are dependent upon the use of proper riding
techniques as well as the expertise of the operator. Every operator should know the following requirements before
riding this motorcycle.
He or she should:


Obtain thorough instructions from a competent source on all aspects of motorcycle operation.

Observe the warnings and maintenance requirements in this Owner’s Manual.

Obtain qualified training in safe and proper riding techniques.

Obtain professional technical service as indicated in this Owner’s Manual and/or when made necessary by mechanical
conditions.

TABLE OF CONTENTS
LOCATION OF IMPORTANT
LABELS
............................................. 1-1
SAFETY INFORMATION
.................. 2-1
DESCRIPTION
.................................. 3-1
Left view .......................................... 3-1
Right view ........................................ 3-2
Controls and instruments ................ 3-3
INSTRUMENT AND CONTROL
FUNCTIONS
....................................... 4-1
Handlebar switch ............................ 4-1
Speed limiter and power
reduction plate ............................ 4-1
Front brake lever ............................ 4-2
Rear brake lever ............................. 4-3
Fuel tank cap .................................. 4-3
Fuel ................................................ 4-3
Fuel tank breather hose ................. 4-5
2-stroke engine oil .......................... 4-5
Fuel cock ........................................ 4-6
Starter (choke) lever “ ” ............... 4-6
Kickstarter ...................................... 4-7
Seat ................................................ 4-7
FOR YOUR SAFETY –
PRE-OPERATION CHECKS
.............. 5-1
OPERATION AND IMPORTANT
RIDING POINTS
................................. 6-1Starting and warming up a cold
engine ......................................... 6-1
Starting a warm engine .................. 6-1
Starting off ...................................... 6-2
Acceleration and deceleration ........ 6-2
Braking ........................................... 6-2
Engine break-in .............................. 6-3
Parking ........................................... 6-4
PERIODIC MAINTENANCE AND
ADJUSTMENT
................................... 7-1
Owner’s tool kit ............................... 7-1
Periodic maintenance chart for
the emission control system ....... 7-2
General maintenance and
lubrication chart .......................... 7-3
Checking the spark plug ................. 7-5
Removing the power reduction
plate ............................................ 7-6
Transmission oil ............................. 7-7
Middle and final gear cases ........... 7-8
Cleaning the air filter element ........ 7-8
Cleaning the spark arrester ............ 7-9
Adjusting the carburetor ............... 7-10
Adjusting the engine idling
speed ........................................ 7-10
Checking the throttle cable free
play ........................................... 7-11
Tires ............................................. 7-11
Panel wheels ................................ 7-13Adjusting the front and rear
brake lever free play .................. 7-13
Checking the front and rear
brake shoes ............................... 7-14
Checking and lubricating the
cables ........................................ 7-15
Checking and lubricating the
throttle grip and cable ................ 7-15
Adjusting the Autolube pump ........ 7-16
Lubricating the front and rear
brake levers ............................... 7-16
Checking and lubricating the
centerstand ................................ 7-16
Checking the front fork .................. 7-17
Checking the steering ................... 7-17
Checking the wheel bearings ........ 7-18
Front wheel ................................... 7-18
Rear wheel .................................... 7-20
Troubleshooting ............................ 7-22
Troubleshooting chart ................... 7-24
MOTORCYCLE CARE AND
STORAGE
.......................................... 8-1
Matte color caution ......................... 8-1
Care ................................................ 8-1
Storage ........................................... 8-3
SPECIFICATIONS
............................. 9-1
CONSUMER INFORMATION
........... 10-1
Identification numbers ................... 10-1

4-1
1
2
3
4
5
6
7
8
9

INSTRUMENT AND CONTROL FUNCTIONS
EAU40660
Handlebar switch
EAU40674
Engine stop switch “OFF/RUN/
START”
Set this switch to “START” before start-
ing the engine. Set this switch to “RUN”
after warming up the engine or before
starting off. Set this switch to “OFF” to
stop the engine.
TIP


The engine cannot be started with
this switch set to the “RUN” posi-
tion.

The engine speed is limited while
this switch is set to the “START”
position, therefore the motorcyclecannot be ridden in that switch po-
sition.
EAU41041
Speed limiter and power
reduction plate
Your motorcycle was delivered with an
adjustable speed limiter and a power
reduction plate. The speed limiter
keeps the throttle from fully opening,
even when the throttle grip is turned to
the maximum. The power reduction
plate is installed in the exhaust mani-
fold to limit the amount of power avail-
able while they learn.
Speed limiter
1. Loosen the locknut.
2. To increase the maximum engine
power available and the maximum
speed of the motorcycle, turn the
adjusting screw in direction (a). To
decrease the maximum engine
power available and the maximum
speed of the motorcycle, turn the
adjusting screw in direction (b).
1. Engine stop switch “OFF/RUN/START”
1

INSTRUMENT AND CONTROL FUNCTIONS
4-2
2
3
45
6
7
8
9
3. Tighten the locknut.
TIP

The adjusting range of the speed limiter
screw is from the fully turned-in positionto 7 mm (0.28 in) turned out. When the
screw is turned out to 7 mm (0.28 in),
the throttle grip can only be opened ap-
proximately halfway. If more power is
required, please consult a Yamaha
dealer.
WARNING

EWA14630
Improper adjustment of the speed
limiter could cause improper throttle
operation. You could lose control,
have an accident or be injured. Do
not turn the adjusting screw out
more than 7 mm (0.28 in) before con-
sulting a Yamaha dealer. Always
make sure the throttle cable free
play is adjusted to 1.5–3.5 mm
(0.06–0.14 in). (See page 7-11.)
Power reduction plate
Once the rider can operate with skill at
the top speed permitted by adjusting
the speed limiter alone, the power re-
duction plate can be removed. (See
page 7-6.)
EAU12900
Front brake lever
The front brake lever is located on the
right handlebar grip. To apply the front
brake, pull this lever toward the handle-
bar grip.
1. Locknut
2. Adjusting screw
1. No more than 7 mm (0.28 in)
1
(a)(b)2
1

1. Front brake lever
1

INDEX
A
Acceleration and deceleration ................... 6-2
Air filter element, cleaning ......................... 7-8
Autolube pump, adjusting ........................ 7-16
B
Brake lever, front ....................................... 4-2
Brake lever, rear ........................................ 4-3
Brake levers, lubricating .......................... 7-16
Brake shoes, checking ............................ 7-14
Braking ...................................................... 6-2
C
Cables, checking and lubricating ............. 7-15
Carburetor, adjusting ............................... 7-10
Care ........................................................... 8-1
Centerstand, checking and lubricating .... 7-16
E
Engine break-in ......................................... 6-3
Engine idling speed ................................. 7-10
Engine oil ................................................... 4-5
Engine, starting a warm ............................. 6-1
Engine stop switch..................................... 4-1
F
Front and rear brake lever free play,
adjusting ................................................ 7-13
Front fork, checking ................................. 7-17
Fuel............................................................ 4-3
Fuel cock ................................................... 4-6
Fuel tank breather hose............................. 4-5
Fuel tank cap ............................................. 4-3
H
Handlebar switch ....................................... 4-1
I
Identification numbers ............................. 10-1
K
Kickstarter ................................................. 4-7
L
Labels, location ......................................... 1-1
M
Maintenance and lubrication, periodic ....... 7-3
Maintenance, emission control system ..... 7-2
Matte color, caution ................................... 8-1
Middle and final gear cases....................... 7-8
Model label .............................................. 10-1
P
Parking ...................................................... 6-4
Part locations............................................. 3-1
Power reduction plate, removing ............... 7-6
S
Safety information ..................................... 2-1
Seat ........................................................... 4-7
Spark arrester, cleaning ............................ 7-9
Spark plug, checking ................................. 7-5
Specifications ............................................ 9-1
Speed limiter and power reduction
plate ........................................................ 4-1
Starter (choke) lever .................................. 4-6
Starting and warming up a cold engine ..... 6-1
Starting off ................................................. 6-2
Steering, checking ................................... 7-17
Storage ...................................................... 8-3
T
Throttle cable free play, checking............ 7-11
Throttle grip and cable, checking and
lubricating.............................................. 7-15
Tires ........................................................ 7-11
Tool kit ....................................................... 7-1
Transmission oil ........................................ 7-7Troubleshooting ...................................... 7-22
Troubleshooting chart ............................. 7-24
V
Vehicle Emission Control
Information label (For Canada) ............. 10-2
Vehicle identification number .................. 10-1
W
Wheel bearings, checking ....................... 7-18
Wheel (front) ........................................... 7-18
Wheel (rear) ............................................ 7-20
Wheels .................................................... 7-13