2010 TOYOTA RAV4 light

395
4-3. Do-it-yourself maintenance
4
Maintenance and care
■
After a fuse is replaced
●If the lights do not turn on even after the fuse has been replaced, a bulb
may need replacement. ( P. 396)
● If the replaced fuse blows again, have the vehicle inspected by your
Toyota dealer.
■ If there is an overload in the circuits
The fuses are designed to blow before the entire wiring harness is damaged.
CAUTION
■To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failing to do so may cause damage, and possibly a fire or injury.
●Never use a fuse of a higher amperage rating than indicated, or use any
other object in place of a fuse.
● Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
This can cause extensive damage or even fire.
● Do not modify fuses or the fuse box.
NOTICE
■Before replacing fuses
Have the cause of electrical overload determined and repaired by your
Toyota dealer as soon as possible.

396
4-3. Do-it-yourself maintenance
Light bulbs
You may replace the following bulbs yourself. The difficulty level of
replacement varies depending on the bulb. If necessary bulb
replacement seems difficult to perfor m, contact your Toyota dealer.
For more information about replacing other light bulbs, contact your
Toyota dealer.
■ Preparing a light bulb for replacement
Check the wattage of the light bulb being replaced. ( P. 473)
■ Removing the engine compartment cover
 P. 352
■ Front bulb locations
Headlight
low beam
Front turn signal, parking and
front side marker lights
Headlight high beam
Front fog lights
(if equipped)

397
4-3. Do-it-yourself maintenance
4
Maintenance and care
■
Rear bulb locations
Vehicles without a spare tire
Vehicles with a spare tire
Rear turn signal and back-up lightsLicense plate
lights
Rear side marker lights
Rear turn signal and back-up lights
License plate
light
Rear side marker lights

398 4-3. Do-it-yourself maintenance
Replacing light bulbs■ Headlights
Right side only: Remove the clip
and move it aside to allow easy
access to the light bulbs.
Turn the bulb base counterclock-
wise.
Headlight (low beam)
Headlight (high beam)
Unplug the connector while
depressing the lock release.
STEP 1
STEP 2
STEP 3

399
4-3. Do-it-yourself maintenance
4
Maintenance and care
Reinstalling the clip
■ Front turn signal, parking a nd front side marker lights
Right side only: Remove the clip
and move it aside to allow easy
access to the light bulbs.
Turn the bulb base counterclock-
wise.
Remove the light bulb.
STEP 1
STEP 2
STEP 3

400 4-3. Do-it-yourself maintenance
Reinstalling the clip
■ Front fog lights (if equipped)
Turn the steering wheel in the
opposite direction of the front fog
light that you wish to replace.
For example, if you wish to
replace the front fog light on the
right side, turn the steering wheel
to the left.
Remove the clip using a flathead
screwdriver wrapped in a rag.
Move section “A” of the fender
liner to the inner side of the vehi-
cle, partly removing it and
thereby allowing access to the
front fog light.
STEP 1
STEP 2
STEP 3

401
4-3. Do-it-yourself maintenance
4
Maintenance and care
Unplug the connector while
depressing the lock release.
Turn the bulb base counterclock-
wise.
■ Back-up lights, rear turn signal and rear side marker lights
Open the back door (P. 46)
and remove the cover.
Turn the bulb base counterclock-
wise.
Rear side marker light
Rear turn signal light
Back-up lightSTEP 4
STEP 5
STEP 1
STEP 2

402 4-3. Do-it-yourself maintenance
Remove the light bulb.Rear side marker light
Rear turn signal light
Back-up light
■ License plate lights
Vehicles without a spare tire
Remove the cover as shown in
the illustration.
Turn the bulb base counterclock-
wise.
Remove the light bulb.STEP 3
STEP 1
STEP 2
STEP 3