2010 SKODA YETI lock

Seats and Stowage
80
Move the hook into another position
– Fold up the hook in direction of arrow page 79, fig. 70 until an angle of
approx. 45° is reached.
– Move the hook in direction of arrow page 79, fig. 70 into the desired position
and fold down the hook as far as the stop in direction of arrow .Remove the hook from the fastening strip– Fold the hook in direction of arrow until it slackens.Install the hook on the fastening strip– Position the hook on the fastening strip in the vertical position in direction of arrow and lightly press it on.
– Fold the hook down in opposite direct ion of the arrow until it locks fully.
WARNING
Please refer to the following guidelines page 78.Fixing nets - Net programme*Fig. 71 Fixing net: double horizontal pock et, floor fixing net / double vertical pocketFixing examples of the fixing net as double horizontal pocket, floor fixing net fig. 71
- left, and double vertical pocket fig. 71 - right.
The fixing nets* and the installation inst ruction are located in the luggage compart-
ment.
WARNING

The whole strength of the net makes it possible to load the pocket with
objects of up to 3.5 kg in weight. Heavy objects are not secured sufficiently - risk
of injury and net damage!

The load to be transported must be fixed in place in such a way that it cannot
move during the journey and when braking.Caution
Do not place any objects with sharp edge s in the nets - risk of net damage.The luggage compartment cover
You can use the luggage compartment cover behind the head
restraints for storing light and soft items.The luggage compartment cover can be remo ved as required if one must transport
bulky goods.Removing the luggage compartment cover– Fold the seat backrests a little forward in order to facilitate the removal of the luggage compartment cover.
– Unhook the support straps  fig. 72.
– Place the cover in th e horizontal position.
A1
A2
A3
A4
A5
A4
Fig. 72 Removing the luggage compart-
ment cover
A1
s2ug.6.book Page 80 Friday, April 9, 2010 2:24 PM

Seats and Stowage
82
Variable loading floor in the luggage compartment*Remove variable loading floorFig. 74 Luggage compartment: Fold up variable loading floor / removeThe variable loading floor makes it easier to handle bulky goods and creates an even
luggage compartment floor when the rear seat backrests are folded forward. The
maximum permissable surface load of the variable loading floor is 75 kg.Removing the variable loading floor– You can fold together the loading floor by moving it in direction of arrow
 fig. 74 .
– Raise the variable loading floor in direction of arrow fig. 74 .
– Pull on both sides of the locking levers in direction of arrow fig. 74 .
– Pull the variable loading floor up and out in direction of arrow .
– The installation of the variable loading floor is carried out in the reverse order.Secure the variable loading floor in the raised position– Fold up the hooks on the fastening strip in direction of arrow page 79, fig. 70 .
– Fold up the variable loading floor behind the seat backrests of the rear seats.
– Fold down the hooks in direction of arrow page 79, fig. 70 as far as the stop.
– Support the variable loading floor on the hooks folded downwards.
WARNING
Pay attention when installing the variable loading floor that the carrier rails and
the variable loading floor are correctly fixed, otherwise the occupants are at
risk.
Note
If the variable loading floor* is installed, no flexible storage compartment can be
installed.Remove carrier railsFig. 75 Luggage compartment: Slacken check points / remove carrier railsRemove carrier rails– Slacken the check points  fig. 75 on the carrier rails using the vehicle key or a
flat screwdriver.
– Grasp the carrier rail at the position fig. 75 and slacken it by pulling in the
direction of the arrow.
– Grasp the carrier rail at the position , slacken it by pulling in the direction of
the arrow and take it out.
– The carrier rail on the other side of the luggage compartment can be removed in
the same way.
A1
A2
A3A4
A1
A3
AB
AA
A1
AA
A2
s2ug.6.book Page 82 Friday, April 9, 2010 2:24 PM

Seats and Stowage85
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Cup holderCup holder in front centre consoleYou can place two cups or beverage cans into the recesses fig. 79 .
WARNING

Do not place any hot beverages into th e cup holder. If the vehicle moves,
they may spill - risk of scalding!

Do not use any cups or beakers which are made of brittle material (e.g. glass,
porcelain). You might be injured by them in the event of an accident.Caution
Do not open the beverages in the cup hold er while driving. They may spill when
braking and while doing so damage the vehicle.
Cup holder in rear centre console*– Press on the panel in the area fig. 80 - the cup holder comes out.
– Pull the cup holder out as far as the stop.
– Adjust the cup holder by moving the locking plate .
WARNING

Do not place any hot beverages into th e cup holder. If the vehicle moves,
they may spill - risk of scalding!

Do not use any cups or beakers which are made of brittle material (e.g. glass,
porcelain). You might be injured by them in the event of an accident.Caution

The cup holder in the rear part of the cent re console must be closed (otherwise it
could get damaged) before folding forward the rear middle seat.

Do not open the beverages in the cup holder while driving. They may spill when
braking and while doing so damage the vehicle.
Fig. 79 Front centre console: Cup holder
Fig. 80 Centre console at rear: Cup
holder
AA
AB
s2ug.6.book Page 85 Friday, April 9, 2010 2:24 PM

Seats and Stowage91
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING
The compartment must only be opened when removing or inserting the spec-
tacles and otherwise must be kept closed.
Caution
On vehicles which are fitted with an anti -theft alarm system*, the opened storage
compartment reduces the effectiveness of the sensors for the interior monitor*.Storage compartment in the front and rear doorsA bottle holder is located in the area fig. 92 of the storage compartment for the
front and rear doors.
WARNING
Use the area fig. 92 of the storage compartment only for storing objects
which do not project so that the effectiveness of the side airbag is not
impaired.
Storage compartment below front passenger seat*The storage compartment is foreseen for storing small objects of up to 1.5 kg. in
weight.
– Tilt the lock to open the flap and pull out the flap fig. 93 .
– Tilt the lock to close the flap and press flap close.Front seat armrest with storage compartment*Fig. 94 Armrest: Storage compartment / cooling of storage compartmentThe armrest is adjustable for height and length.Opening storage compartment– Open the lid of the armrest in the direction of arrow fig. 94 .
Fig. 92 Storage compartment in the
front doors
AB
AA
Fig. 93 Front passenger seat: Storage
compartment
A1
s2ug.6.book Page 91 Friday, April 9, 2010 2:24 PM

Seats and Stowage
92
Closing storage compartment
– Open the lid up to the stop, then you can fold it downwards.Setting height– First of all fold the lid to the bottom and lift it in the direction of arrow into one of the 4 fixed positions.Adjusting in forward/back direction– Push the lid into the desired position.Opening air inlet– Pull the lock page 91, fig. 94 in upward direction.Closing air inlet– Push the lock as far as the stop downwards.
On vehicles fitted with ai r conditioning, the storage compartment is equipped with a
lockable inlet for thermally treated (warmed-up) air.
At open air supply, air flows into the storag e with a temperature which is as high as the
one out of the air outlet nozzles, depending on temperature setting.
The air inlet in the storage compartment is connected to position
 through adjust-
ment of the control dial for air distribution. This position causes the maximum amount
of air to flow into the storage compartment (depending on the rotary regulator posi-
tion for the fan).
You can use the storage compartment, for example, to temper drinks cans, etc.
If you do not use the air inlet in the storage compartment, the end cover should
always be kept closed.
Note
Push the lid of the armrest up to stop to the rear before operating the handbrake.
Storage compartment in rear centre console*The storage compartment is equipped with a removeable insert.
– Open the storage compartment by pullin g on the upper edge of the storage
compartment fig. 95 in the direction of arrow.
WARNING
The storage compartment is not a substitute for the ashtray and must also not
be used for such purposes - risk of fire!
Caution
The storage compartment in the rear part of the centre console must be closed (other-
wise it could get damaged) before folding forward the rear middle seat.
AAAA
Fig. 95 Centre console at rear: Storage
compartment
AA
s2ug.6.book Page 92 Friday, April 9, 2010 2:24 PM

Seats and Stowage93
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Storage compartments in the luggage compartment*Fig. 96 Luggage compartment: Storage compartmentsStorage compartments are located on bo th sides of the luggage compartment.
The removeable storage compartment fig. 96 on the left side is suitable for
stowing small objects weighing up to 1.5 kg.
The storage compartment fig. 96 on the right side is suitable for stowing small
objects weighing up to 0.5 kg.Flexible storage compartment*A flexible storage compartment is located on the right side of the luggage compart-
ment. The flexible storage compartment is foreseen for storing small objects of up to 8
kg. in weight.
Removing– Take hold of the flexible storage compartment at both upper corners.
– Press the upper corners to the inside and release the storage compartment by
pulling upwards.
– Remove by pulling towards you.Installing– Insert both ends of the flexible storage compartment into the openings of the right side trim panel of the luggage compartmen t and push it downwards until it locks.Clothes hooksThe clothes hooks are located on the middle pi llar and on the handle of the headliner
above each of the rear doors.
WARNING

Ensure that any clothes hanging from the hooks do not impair your vision to
the rear.

Use the hooks for hanging only light item s of clothing and ensure that there
are no heavy or sharp-edged objects in the pockets.

The maximum permissable load of the hooks is 2 kg.

Do not use clothes hangers for hanging up items of clothing otherwise this
will interfere with the protection offered by the head airbag*.
AA
AB
Fig. 97 Flexible storage compartment
s2ug.6.book Page 93 Friday, April 9, 2010 2:24 PM

Seats and Stowage
94
Removeable through-loading bag*The removeable through-loading bag is solely used for transporting
skis.Loading– Open a rear side door of the vehicle.
– Fold the backrest of the middle seat forwards page 74.
– Place the empty removeable through-load ing bag in the gap between the front and
rear seats in such a way that the end of the bag with the zip lies in the luggage
compartment.
– Open the boot lid.
– Push the skis into the removeable through-loading bag from the luggage compart- ment  .
– Close the removeable through-loading bag with the zip.Securing– Pull the securing belt with both lock to ngues out of the pocket of the removeable
through-loading bag.
– Insert the lock tongues fig. 98 in the belt locks of the rear middle seat belt
, first of all on the one side and then on the other side.
– Place the securing belt in the middle of the skis between the heel and the tip of the
bindings and pull the secu ring belt tight at the free end of the belt .
WARNING

After placing the skis into the remove able through-loading bag, you must
secure it with the securing belt .

The securing belt must hold the skis tight.

Ensure that the securing belt for skis grasps the middle between the tip and
the heel element of the bi nding (see also imprint on the removeable through-
loading bag).Note

The removeable through-loading bag is foreseen for two pairs of skis. The total
weight of the skis which are transported must not exceed 10 kg.

You must put the skis and the sticks in the removeable through-loading bag with
the tips facing the rear.

If there are several pairs of skis in the removeable through-loading bag, ensure that
the bindings are positioned at the same height.

The removeable through-loading bag must never be folded together or stowed
when moist.
Fig. 98 Securing the removeable
through-loading bag
AA
AC
AB
AA
s2ug.6.book Page 94 Friday, April 9, 2010 2:24 PM

Heating and air conditioning system
106WARNING

The auxiliary heating must never be op erated in closed rooms - risk of
poisoning!

The auxiliary heating must not be runn ing during refueling - risk of fire.

The exhaust pipe of the auxiliary heating is located on the underside of the
vehicle. Therefore do not place the vehicl e, if you wish to operate the auxiliary
heating, in such a way that the exhaust gases of the auxiliary heating can come
easily into contact with inflammable materi als (e.g. dry grass) or easily inflam-
mable substances (e.g. fuel run out).Note
If the auxiliary heating runs, the fuel co nsumption comes from the vehicle tank. The
auxiliary heating automatically controls the filling level in the fuel tank. If only a low
quantity of fuel is present in the fuel tank, the function of the auxiliary heating is
blocked.
The exhaust pipe of the auxiliary heating, which is located on the underside of the
vehicle, must not be clogged and the exhaust flow must not be blocked.

If the auxiliary heating and ventilation is running, the vehicle battery discharges. If
the auxiliary heating and ventilation has be en operated several times over a longer
period, the vehicle must be driven a few ki lometers in order to recharge the vehicle
battery.

The auxiliary heating only switches the blower on, if it has achieved a coolant
temperature of approx. 50 °C.

At low outside temperatures, this can result in a formation of water vapour in the
area of the engine compartment. This is quite normal and is not an operating problem.

After switching off the auxiliary heating, the coolant pump runs for a short period.

The auxiliary heating and ventilation does no t switch on or comes on, if the vehicle
battery indicates a low loading state.

The auxiliary heating (auxiliary heating) does not switch on, if the following was
shown in the information display or before switching off the ignition: Please refuel!

The air inlet in front of the windscreen must be free of ice, snow or leaves in order
to ensure that the auxiliary heating operates properly.

So that warm air can flow in to the vehicle after switching on the auxiliary heating,
you must maintain the temperature normally selected by you (we recommend 22 °C
for Climatic, Climatronic and for the heat ing turn the regulator to the right
 page 97, fig. 101 ). It is recommended to put the air flow in the position
.

On vehicles with DPF (diesel particle filt er) the warm coolant heats up the engine.
Direct switching on/offThe auxiliary heating (auxiliary heating and vent ilation) can be switched on or off at any
time directly using the button on the operating part of the Climatic, Climatronic or
heating fig. 104 .
If the auxiliary heating and ventilation is not switched off earlier, it switches off auto-
matically after the expiration of the set operating period, in the menu Running time.
Note
A radio remote control for the auxiliary heating can be obtained from Škoda original
accessories.
AA
Fig. 104 Button for direct switching
on/off of the auxiliary heating (auxiliary
heating and ventilation) on the operating
part of the Climatic

s2ug.6.book Page 106 Friday, April 9, 2010 2:24 PM