General information
9
Climatronic If your vehicle is equipped with climatronic, a feedback is received on the screen when changing the settings. Display of time You can switch the display of the time on or off in the menu
Setup System
.
Switching the system on and off– The system is switched on or off by pressing the control button . The last active audio source before switching off is repeated. If the key is pulled out of the ignition lock while the unit is switched on, the unit will switch off automatically. You can then switch the unit on again. If the
ignition is switched off, the unit (discharge
protection of the vehicle battery) switches
off automatically after approx. one hour.
This process can be repeated as often as necessary.Anti-theft protectionThe anti-theft coding of your navigation sy
stem prevents an operation of the system
after a voltage interruption, e.g. during a vehicle repair or after theft. After discon-necting the battery, disconnecting the navigati
on system from the on-board voltage of
the vehicle and after a fuse failure, the code
must be entered before the vehicle can be
used again.Enter code– If a keypad appears after switching on
with the command to enter the code, the
unit can be unlocked by entering the corr
ect four-digit code number. The number
of the possible attempts is shown in the second touch-screen line.
– Press a digit from to on the digit block displayed on the screen. The digit is
accepted in the entry line.
– After a four-digit order has been entered, the group of digits will turn grey (inactive)
and no further digits can be accepted in the entry line.
– Press on the touch-screen to erase the digits in the entry line from right to left
and thereby correct your input, if necessary.
– If the correct code number is di
splayed in the entry line, press .
Code number The code number can only be called up “onlin
e” via the Škoda system, as this guaran-
tees even more effective anti-theft protec
tion. Please contact your Škoda dealer if
necessary. Incorrect code number If an incorrect code is confirmed after entry
of the code, the procedure can be repeated
once again
. The number of possible attempts is
shown in the second line on the
touch-screen. If the code number is entered incorrectly fo
r the second time, the unit will be blocked
for approx. one hour. It is possible to ente
r again the safety code
after one hour has
expired, when the unit and the ig
nition have been switched on.
If two invalid attempts are then made agai
n, the navigation syst
em will be blocked
again for an hour. The cycle - two attempts, blocked for
an hour - will continue to apply.
Note
The code is normally stored in the instrument
cluster. This ensures that it is automati-
cally decoded (convenience coding). Ma
nual input of the code is normally not
necessary.
A1
0
9
OK
s32k.a.book Page 9 Friday, September 18, 2009 1:54 PM
Range selector key SETUP
13
– To change the assignment of a particular shortcut key, select the respective
shortcut key by pressing the key in the following menu.Note
The selection possibilities of the phone se
t-up depend on the relevant telephone
preinstallation.Setup SystemCall up the
Setup System
menu by pressing the range se
lector key and the func-
tion key .Change the system language manually– Press the button and select the de
sired language in the opening pop-up
window. When selecting the menu point “
automatic
”, the system language is the
language which is set in th
e menu of the information disp
lay. If desired, another
language can be selected for the unit.
Changing system set-ups– You can change the set-up of the distance unit. – You can change the set-up of the time format. – You can change the set-up of the date format.Time display– If you press the function key , while in the menu
Setup System
, the
automatic time display is set in the touch-screen.
– Time display in the operating modes radio, media and map. – The current time is taken over by
the instrument cluster in the vehicle.
– After switching off the unit, the time continues to show.Reset the factory settings on the unit– Press on the function key in the menu
Setup System
.
– Now find the settings you wish to reset. – If you press the function key and confirm the following safety interrogation
the selected settings will be reset to the factory settings and all the stored data will be erased.
“ Time
” and “
Date
” settings need only be carried
out manually under
certain circum-
stances. Time and date will normally be a
ccepted automatically from the vehicle into
the unit.Setup DisplayCall up the menu
Setup Display
by pressing the range selector key and the
function key .Brightness– Press on the function
key behind and select a setting in the pop-up
window.
– Press the function key if the brightness of the touch-screen should
automatically be adapted to the current ligh
t conditions via the sensors on the unit.
– Press one of the other function keys to
manually adjust the brig
htness of the touch-
screen.
Day/night– Press on the function key behind and select a setting in the pop-up
window.
– Press the function key if switching
the headlights on and off should also
change the map display from night to day design.
– Press on the function key or to manually determine the night and day
design of the map display.
SETUP
System
Language
time displayFactory settings
Reset
SETUP
Display
Brightness
Automatic
Day/night
Automatic
Day
Night
s32k.a.book Page 13 Friday, September 18, 2009 1:54 PM
