2010 SKODA OCTAVIA change time

Range selector key MAP
53
Range selector key MAPMap displayBy pressing the range selector key you
can move from any menu into the map
display. Pressing the range selector key will op
en or close an split-screen in the map
display, where further informatio
n can be displayed and selected
⇒page 56, “Split-
screen in the map display”. During route guidance the map display will di
ffer in some points from the “normal”
map display. During the rout
e guidance the driven route will be highlighted, symbol
9, shows the current vehicle position
⇒fig. 24
- in the bottom line behind the third
function key
 and the distance to the destination and, behind
 the estimated time
of arrival or driving time will be displayed. Parts of the road ahead can also be blocked manually during route guidance.Use the function key to insert or fade out the bar with the function keys in each display.
Center the map display for vehicle position or travel destination You can move the indicated map section by pr
essing your finger on the touch-screen
and sliding it over the touchscreen. If you have moved the touch-sc
reen section, a further function key will be faded in at
the top right under the compass display function key
³ ⇒fig. 24
. Pressing this func-
tion key will center the map again for the current vehicle position. In some map displays you can center the di
splay of the travel destination with the
function key . Change the type of display The symbol in the second function key
5, 6 or 7 shows the currently selected type
of display. To change these, briefly press press the function key and select a different type of display in the pop-up wind
ow by pressing the selection again.
5-2D
- Two-dimensional:
Plan view of a conv
entional map display.
6-3D
- Three-dimensional: Map display, diag
onally from the front in bird's-eye
perspective.7-To p o g ra p h i c
- Plan view of a conventional ma
p display with coloured display of
various terrains (Mo
untains, Valleys etc.).
The function key in the map display without route guidance Pressing on the function key will op
en a pop-up window
with settings for
navigation.
- starts route guidance or continues route guidance to the travel
destination selected in the main menu
Navigation
.
- calls up the menu
New dest.
to change the travel destination
selected in the main menu
Navigation
.
- to change the parameters for route calculation.
- stores the current vehicle position
as flagdest. in the destination memory.
Fig. 24 3D map display during a

route guidance (map section moved).
MAPMAP
8
1
Navigation
Navigation
Start route guidanceEnter new destinationRoute options$
s32k.a.book Page 53 Friday, September 18, 2009 1:54 PM

Range selector key MAP
54For further functions of the navigation syst
em, e.g. changing the travel destination,
open the main menu
Navigation
by pressing the range selector key .
The function key in the map display during a route guidance Pressing the function key
⇒page 53, fig. 24
will open a pop-up window with
set-ups for route guidance.
- stops route guidance at the cu
rrent position. The route guidance
can be continued at any time by pressing the function key and
.
- calls up the menu
New dest.
in order to enter a stopover to
be approached during
current route guidance.
- used for the manual entry of a congestion ahead and the recom-
mendation of the next available route.
- to change the parameters for route calculation.
- stores the current vehicle position
as flagdest. in the destination memory.
For further functions of the navigation, open the main menu
Navigation
by pressing
the range selector key . Control media source The function key displays the currently selected media source (here the radio station “Radio 2”). To control the selected media source, briefly press the function key and select a station (radio mode) or title (media mode) by pressing the selection in the pop-up window. Radio mode:
The six station keys of the main menu
RADIO
are faded in.
Media mode:
The title name and the function ke
ys for controlling the current media
source are faded in. Function keys Pressing the function key will open a
pop-up window for further set-ups and
displays.
- shows the currently selected travel destination in the map display in
the main menu
Navigation
. Use the function key on the right under the compass
display to center the map ag
ain on the vehicle position.
- changes between day and night design.
- opens the split-screen. The split-screen can be opened or closed in the
map display by pressing the range selector key .
- during route guidance, when driving and turning on roads with
more than one lane, a small split-screen with
lane guidance will be inserted in the map
display. A tick in the check-box
= indicates that the function is switched on.
- switches the touch-screen
into energy save mode.
Scale modification and display Pressing the function key with the display
of the currently selected map dimension at
the bottom right will insert further function
keys for changing the map detail and the
map scale. If not used, these function
keys fade out again after five seconds.
- briefly switches the map display to the
overview display (small scale). It returns
again to the last display (large scale) after a few seconds. or - to zoom in or out of the map, i.e.
changing the map scale. Alternatively, move
the sliding regulator
? within the scale.
- switches to the overview map with start and finish point during route guid-
ance.
- for switching on the autozoom during a route guidance. If “Autozoom” is active,
the map scale will change automatically depending on the driven route (Motorway trip: large map scale - city: small map scale). The switched-on Autozoom is displayed in the scale display by
{. Press again to switch off
or manually change the scale
with the set button . Display favourite symbol A favourite category can be determined for stored destinations. Favourite destinations are displayed in the map, depending on set-up, with their assigned favourite symbol.
NAV
 ... /...... /...
Stop route guidance
Navigation
Start route guidanceEnter stopover destinationCongestion aheadRoute options$
NAV
Radio 2Extras
Extras
Destination viewDay/night
Split-screen
MAP
=Lane guidanceSwitch off display/+
-
h-3
{
{
A8
s32k.a.book Page 54 Friday, September 18, 2009 1:54 PM

Range selector key PHONE
59
Call lists are always assigned to a user profile and are only displayed once the corre- sponding SIM card is connected agai
n with the mobile phone preparation.
Shortcut keysAt the time of the first connection with th
e SIM card of your mobile telephone all
shortcut keys have still not been assign
ed after the first call from the main menu
PHONE
.
Assigning free shortcut keys– If you press briefly on a non-assigned shortcut key the menu
Speed dial
will open
to enable a name and phone number to be entered.
– If you press the function key , an input mask will open to enable a name to
be assigned.
– If you press the function key a mask
will open to enable a number to be
assigned.
– Press the function key or to accept a call number for
these shortcut keys from
the correspo
nding list.
– Press the function key to erase all entries in all entry lines at once after confir-
mation with .
– If you have completed your entries in the Menu
Speed dial
, press the function key
.
– The entered name will be displayed in
the shortcut key of the main menu
PHONE
.
The call number entered will be assigned to a shortcut key.
Calling up a connection via the shortcut key–Briefly press an
assigned
shortcut key to establish th
e connection to the assigned
call number.
Modifying assigned shortcut keys– If the assignment of a shortcut key is
to be modified, keep
pressing the corre-
sponding shortcut key until the menu
Speed dial
has opened for modification.
The assignment of the shortcut keys remains stored in the unit and will only be displayed again when the corresponding SIM
card is connected again to the mobile
phone preparation program. Shortcut key The shortcut key has not yet been assigned a call number in the factory, as this depends upon the
corresponding mobile phone
company and country. The
name for this shortcut key has, however, been specified and cannot be changed. You should now store your mail box number so th
at you can quickly check your voice mail.
Editing field: further input possibilities - changes from upper case to lower case and vice versa. - opens the editing field for the entry of digits and special characters. The button
changes to . Press on , to change again to the letter editing field.
- space key for entering spaces. or - moves the cursor in the entry line to the left or right. - deletes characters in the entry line from
right to left, starting from the position of
the cursor.Phone conversationIf you have started the process of connecti
ng to a call number or accepted a call, the
main menu
PHONE
will change to the display
Phone conversation
.
Incoming phone call– An incoming phone call will be
displayed on the display by “
Incoming call
”
followed by the call number of the caller. If
the number of the caller is stored in the
telephone book, the name of the caller will be displayed instead of the call number.
– Press the function key to accept the call.– Press the function key to reject the call.
NameNumber
Call lists
Telephone book
<
OK
OK
Voice mailboxVoice mail box
:;
A-Z
A-Z
‚
b

^
s32k.a.book Page 59 Friday, September 18, 2009 1:54 PM

Voice control of the radio navigation system
61
Voice control of the radio navigation systemGeneral informationIntroductionThanks to this equipment, you can operate
a few functions of your radio navigation
system via the microphone installed in the vehicle; a so-called “
Speak what you see
on the touch-screen
” system.
You can use the voice control in the operating modes
RADIO, MEDIA, PHONE, MAP
and NAV
.
You can change the volume any time during
the call with the control button of the
unit
⇒page 3.
Switch on voice control (dialogue)•
By briefly pressing the button on the unit.
Switching off voice control (dialogue)•
By pressing the button on the unit for at least 5 seconds.
•
By briefly pressing the button on the
unit, when the system is waiting to
pronounce a new command.•
By pressing one of the buttons which are located on the side of the touch-screen
of the unit or by touching the touch-screen
(if the button is not pressed in the
help display).•
By pronouncing the command “
Cancel
”.
•
If the system does not receive a command or does not recognise the command
while the dialogue is switched on, it answers with the question “
Pardon?
” and thus
makes it possible to pronounce a new co
mmand. If the system does not receive a
second voice command, you will be offered help
. If the system does not receive a third
voice command, you receive the message “
Cancel
” and the voice control switches off.
Optimum understanding of the commands depends on several factors:•
Speak with a normal tone of voice wi
thout intonation and excessive pauses.
•
Avoid a bad pronunciation.
•
Do not use any abbreviations - al
ways pronounce the full command.
•
Do not speak, if the system makes an announcement. As long as the system has not
finished the announcement, it will
not react to an additional command.
•
Close the doors, windows and sliding roof, in order to avoid disturbing influences
of the environment on the understanding of the commands.•
We re c o m m e n d t o s p e a k l o u d e r a t h i g h e r s p e e d s ; b u t w i t h a c a l m v o i c e , s o th a t t h e
increased surrounding noise does not drown out the command.•
During the dialogue limit additional noise in the vehicle, e.g. simultaneously talking
occupants.•
The microphone for voice control is directed
to the driver as well as to the front
passenger. Therefore the driver and the front passenger can operate the unit.DialogueThe period of time in which the system
is ready to receive voice commands and to
carry them out is call
ed a dialogue. The system reacts
with an audible feedback and
guides you through the individual functions. Selecting long and short dialogue The nature of the dialogue can be set by
pressing the button on the unit and by
pronouncing the command “
long dialogue
” or “
short dialogue
”.
The nature of the dialogue can also be
set manually in the operating mode
SETUP
-
- or .
If you select the short dialogue, the system shortens some messages or replaces them by an audible si
gnal (gong), thus the operation is accelerated.
If you select the long dialogue, the system
gives the whole message without shortening
it. The entered voice commands are the same for the long and short dialogue. Interrupt messages The message just given can be ended by br
iefly pressing the button on the unit.
Thus, it is possible to pronounce
an additional voic
e command sooner.
A1



Fa d e o u t

Voice control
Long dialogue
Short dialogue

s32k.a.book Page 61 Friday, September 18, 2009 1:54 PM

Škoda Auto pursues a policy of constant product and model development. We trust
that you will understand that changes to models in terms of shape, equipment and
engineering, may be introduced at any time. The information about scope of delivery,
appearance, performances, dimensions, weight, fuel consumption, standards and
functions of the vehicle is only correct at the time of publication. Certain items of
equipment might only be installed later on (information given by the local authorised
Škoda Service Partner) and only envisaged for particular markets. It is therefore not
possible for legal claims to be made based on the data, illustrations and descriptions
contained in this Owner's Manual.Reprinting, reproduction or translation, either in whole or in part, is not permitted
without the written consent of Škoda Auto.
Škoda Auto expressly reserves all rights relating to copyright laws.
We reserve the right to make changes to this document.
Issued by: ŠKODA AUTO a.s.
© ŠKODA AUTO a.s. 2009s32k.a.book Page 68 Friday, September 18, 2009 1:54 PM