2010 SKODA OCTAVIA window

General information7
current menu.
“Pop-up window”
If you press the function key on the screen, a so-called “pop-up window” will open
in which all possible set-up options are displayed.
Briefly press the desired set-up option. The pop-up window will disappear and the
newly selected set-up option is displayed in the function key.
“Check box”
Some functions can only be switched on or off.
There is a so-called “Check box” in front of a function which can only be switched on
or off. A tick in the check box
=
indicates that the function is switched on, an empty
check box
>
, indicates that it is switched off.
Briefly press the corresponding function key for switching on or off.
Input mask for free text inputIn some of the menus you can enter a free text, for example, when entering a new
destination or while searching for the name of a point of interest.
– Press to accept a character sequence offered by the system or press in
order to delete the characters in the entry line.
– When in the entry window, press on a character shown on the keypad block to accept it into the entry line. – You can also delete or change the characte
r sequence in the entry line as well as
insert additional characters.
Further input possibilities: - changes from upper case to lower case and vice versa.
- opens the input mask for digits and special characters. The function key changes
to . Press , to change again to the letter input mask.
˜
- space key for entering spaces.
- switches to the Cyrillic script.
or - moves the character entry cursor (the cursor) in the entry line to the left or
right.
- opens a pop-up window with special characters. - deletes characters in the entry line starting from the position of the character
entry cursor from right to left.
Selecting letters based on specific characters
Some letters in the input masks are also marked with a small triangle “
a”. This indi-
cates that specific characters based on this letter can be selected.
Continue to press down on the correspondin g function key with your finger until a
pop-up window with these specific characte rs can be displayed. Press to accept the
desired character into the entry line - the po p-up window will close. If no entries are
entered, the pop-up window will clos e automatically after a few seconds.
Input mask for selecting the destination address
AE
AF
Fig. 2 Input mask for free text input
OK
Delete
:;A-Z
A-Z
~‚
b
ÄÜDelete
Fig. 3 Input mask for selecting the
destination address
s34g.6.book Page 7 Thursday, January 14, 2010 8:48 AM

General information
8
When entering the destination address, it is only possible to enter the characters in the
sequence which corresponds to the destinations stored in the navigation system.Limit destination and select from the list– You can open a list of the selectable dest inations any time by pressing the function
key while making entries in the entry line. Only destinations selectable
from the navigation memory which corres pond to the requirements and the char-
acter sequence in the entry line will be displayed.
– The number of selectable destinations will be displayed in the entry line if fewer
than 99 destinations can be selected.
– If fewer than six destinations are selectable, the entry window will close automati- cally and a list of possible de stinations will be displayed.
List/OK
s34g.6.book Page 8 Thursday, January 14, 2010 8:48 AM

Range selector key SETUP9
Range selector key SETUPSound settingsBy pressing the button and pressing on the function key in the RADIO
mode, you can select the following para meters using the menu control button :•
- , ,
and - Volume when switching on, volu me of incoming traffic announcements,
volume of navigation announcements an d speed dependent volume adaptation;
•
- Treble setting;
•
- Midtone setting;
•
- Bass setting;
•
- Setting of the volume ratio between the left and right side;
•
- Setting of the volume ratio between the front and the rear;
•
* - Setting the equalizer (linear, language, rock, classical, dance);
•
* - Setting of the surround tone.
GALA function
Your radio increases automatically its volume with the increasing vehicle speed. A
higher setting value results in a stronger volume increase.
Note
You can set the tone parameters using the menu control button or the function keys
or .System settingsPress the button and select the function key .
You can select between the following parameters:•
- Menu language for the displa ys and the language messages;
•
- Keypad layout for text entry;
•
* - if your vehicle is equipped with climatronic, the setting change
is displayed when it is activated;
•
- Setting the brightness of the screen;
•
- Factory settings;
•
- the information regarding the complete memory capacity of the
SD card and the size of the memory assigned to the navigation data is displayed on the
screen;
•
- Removing the SD card.
Setup radioPress the button in the RADIO mode.Switching the traffic announcements on or off– If you wish to switch the reception of traffi c reports on or off, press the function key
. Determining the station selection via the arrow buttons – By pressing on or , you can select the source from which the stations are to be selected while in the RADIO mode using the arrow buttons. If
is selected, only stored stations from the preset list are called up using the
arrow buttons during station relay. The symbol “
ƒ C
„” is displayed on the
screen.
Switching the RDS function on or off (RDS regional)– Press on the function key (regional station) and select a set-up in the
opening pop-up window.
– Press on the button , doing so always chooses the frequency for the heard radio station which offers the best reception at the present time.
– When pressing on the button , the unit attempts to hold a radio station emit-
ting regionally long enough until the receptio n quality is so bad, that there is a risk
of a program loss.
SETUP
Sound
A10
Vo lume
Max. switch-on volume
Traffic announcements (TP)
Navigation volume
SDVATre b l eMid-rangeBassBalanceFa d e rEQ settingsSurround
A10
+
-
SETUP
System
LanguageKeypad layout
Air con. displaysScreenFactory settingsSD card statusRemove SD card
SETUP
Traffic announcements (TP)
Arrow buttons
Station list
Presets
Presets
RDS regional
Automatic
Fixed
s34g.6.book Page 9 Thursday, January 14, 2010 8:48 AM

Range selector key SETUP
10
Delete stored stations
– Press the function key and confirm the following safety interrogation in order to delete all radio stations stored in the memory list.Setup Telephone*Call up the Setup Telephone menu by pressing the range selector key and the
range selector key .Entering the voice mailbox number– If you want to enter the voice mailbox number (this number depends on the type
of the mobile phone network) in a mobile phone, press the function key . The entry of the voice mailbox number is intended for
listening to the messages left on a mobile phone.Updating telephone book in the unit– Press on the function key to update all entries in the unit, the
telephone book of the mobile phone or th e SIM card entered since the last connec-
tion. This procedure can take a few minutes.
– Confirm the following safety interrogatio n. The “old” data in the telephone book
can still be selected at the unit while the data is being updated.Delete call lists– Press on the function key .
– If you confirm the following safety interrogation by pressing , the stored call numbers of all calls made and calls accepted in the unit will be deleted.Deactivating the telephone module– After pressing the function key the mobile phone
deregisters from the network (this function is only available for the universal tele-
phone preinstallation GSM III).Factory settings– Sets the telephone preinstallation to the basic setting.
Note
The selection possibilities of the mobile phone set-up depend on the relevant type of
the universal telephone preinstallation.Setup traffic programmePress the range selector key and then the range selector key .
Switching the traffic announcements on or off
A tick in the check box
=
indicates that the traffic pr ogramme function is already
switched on.
Dynamic route
Opens a pop-up window where it is consider ed if the TMC traffic reports, received
during the route calculation, are to be entered.
Setup DisplayPress the button in the RADIO mode and then the function keys and
.Brightness– Press the function key and select the desired setting for brightness (5°stages) in a pop-up window.
– A light sensor, which is located in the top ri ght corner of the front panel, is used for
the automatic correction of the brightness depending on the light conditions in the
vehicle.Day/night– Press on the function key and sele ct a setting in the pop-up window.
– Press the function key if switching the headlights on and off should also change the map display from night to day design.
– Press on the function key or to manually determine the night and day design of the map display.
Delete presetsAll
PHONE
SETUP
Enter voice mailbox number
Load telephone bookDelete call lists
Delete
Deactivate the telephone module
TMC
SETUP
Traffic announcements (TP)
˜Dynamic routeSETUP
System
Screen
BrightnessDay/Night
Automatic
Day
Night
s34g.6.book Page 10 Thursday, January 14, 2010 8:48 AM

Range selector key SETUP11
Confirmation tone
– Press on the function key and select a setting in the pop-up
window.
– Press or to switch the tone for confirmation of a function key operation on the screen on or off.Media set-upsPress the button in the MEDIA mode.
Function keys in the menu°-°Media•
- a tick in the check box
=
means that the function of
the traffic programme is switched on.
•
- Check box for setting the play function mode Scan, Mix
and Repeat incl. sub-folder (“switched on”) or without sub-folder (“switched off”).
•
- Setting the volume of the external audio source (audio source AUX
is located on the unit).
•
* - Setting the volume of the external audio source (the audio source
MDI is located under the armres t of the front seats or in a storage compartment on the
front passenger side).
•
* - enables a wireless transfer of MP3 data to the tele-
phone preinstallation. Enables the audio play function by means of Bluetooth interface
of portable units (mobile phones) which support the protocol A2DP.
Navigation settingsPress the button in the Navigation mode.
Function keys in the menu°-°Navigation•
- determine the criteria according to which a route is to be calcu-
lated and what types of destinations you wish to assign.
•
, , and - route
criteria, dynamic route guidance, route wi thout motorways and route without toll
roads/ferries.
•
- Setting the volume of the navigation announcements.
•
- changes between day and night display, as well as automatic, if the
map display changes automatically accordin g to the setting of the light switch.
•
- displays a point of interest on the map.
•
- changes the map scale automatically depending on the speed and the
driven route (Motorway trip: small map scale - City center: large map scale).
•
- the speed limit for the current section of the route is indicated
at the top left of the screen.
•
- during a route guidance, either the arrival or the driving time is
shown in the map display.
•
- Enter home address.
•
- you can start a virtual (apparent) route guidance in the demo mode.
Virtual route guidance will be repeated when reaching the fictive travel destination.
Stop virtual route guidance normally and de activate the demo mode to restart “real”
route guidance. As in this case the unit must first reorient itself it can take some time,
depending on the number of the currently tracked satellites, until the unit has again
found the real location. Drive a short distance.
•
- Entering a fictive (invented) starting point in the demo
mode.
•
- Deleting the destination memory or the list of the last
destinations.
•
- Display of information via the data base on CD or SD card,
delete the data base of the SD card or copy the data.
Route criteria
Fa st : calculates the fastest route to the dest ination, even if a detour is necessary.
Short : calculates the shortest route, even if a longer driving time is necessary. Please
note that the setting “Short route” during route guidance can sometimes lead to unex-
pected results.
Economical : calculates a route with a driving time as minimal as possible and a driving
distance as short as possible.
Confirmation tone
On
OffSETUP
Traffic announcements (TP)Scan/mix/repeat incl. AUX volumeMDI volumeActivate Bluetooth audio?
SETUP
Route optionsRoute criteria
Dynamic route
Avoid motorways
Avoid toll roads/ferries
Announcement volumeDay/NightPOIs on mapAutozoomTraffic sign displayTime displayEnter home addressDemo modeDemo mode starting pointDelete destination memoryNavigation data basis
Route criteria
s34g.6.book Page 11 Thursday, January 14, 2010 8:48 AM

Range selector key RADIO13
Range selector key RADIORadio modeRetrieve radio stationCall up main menu RADIO and choose frequency range– Press the range selector key . The currently heard radio station is displayed
in the middle of the screen ⇒page 6, fig. 1 .
– Press the range selector key to change the frequency range. Alternatively, you can press on the function key ⇒fig. 4 in the main menu RADIO and
select or in the pop-up window.
Changing radio station– By briefly pressing the function keys or , you can change to the previous or
following radio station of th e selected frequency band.
–If the symbol “ TP” is displayed on the screen, you can only change over to the radio
stations with traf fic announcements.
–If the symbol “
ƒ C
„” is displayed on the screen, you can only change over to
the stored radio stations.
Select a radio station from the station list– If you wish that all the presently receivab le radio stations are displayed, press on
the function key and then on the function key . The list “skips”
directly to the display of th e currently heard radio station.
– Select the desired radio statio n using the menu control button .Change radio station in the memory list– Press the function key and then the function key and select
the desired radio station using the function keys - .Manual station finding– If you wish to set the radio station manually using its frequency, press the function key and then the function key .
– Set the radio station using the menu cont rol button or using the arrows and
on the unit.
– Briefly press the menu control button to terminate the manual frequency selection and to display once again the function keys.Scan function– In order to start the automatic play in the current frequency range, press the func-
tion key and then the function ke y . All radio stations with strong
reception are automatically played for appr oximately five seconds according to the
sequence in the station list.
Fig. 4 Menu radio: Function key bandFig. 5 FM station list
RADIO
AA
RADIO
Band
FM/List
AM
ƒ
„
Band
FM/List
A10
Extras
Dest. memory
1
24
Extras
Manual
A10
ƒ
„
Extras
Scan
s34g.6.book Page 13 Thursday, January 14, 2010 8:48 AM

Range selector key RADIO
14
– Press on the function key to end th e automatic play of the currently heard
radio station.Save radio stationSave radio station– Press the function key and then the function key in order to
open the preset list.
– If you wish to store the displayed radio station in a memory space, press one of the displayed station keys to and hold it pressed for so long until a signal
sounds. The currently heard radio station is then stored on this station key.Deleting a radio station from the memory list– Press the button in the RADIO mode and then the function key
.
– Select the radio station you wish to de lete and confirm by pressing the menu
control button .
– If you wish to delete all the stored radio stations, press on the function key .
Note
It is alternatively possible to store radio st ations by pressing the menu control button
.Calling up a radio station
Calling up a station via the station keys– Press the button ⇒fig. 6 and then the function key and the function
key .
– You can select the station stored on one of the station keys to in the main
menu RADIO by briefly pressing the desired station key.Calling up available stations from the memory list– Press the button and then th e button and the function key .
– Select the desired radio statio n using the menu control button .RDS function– If you wish to switch the display of additional information to a radio station on or
off, press the button , the function is displayed in the top right corner of the
screen by the letter “i”.
RDS (“ Radio Data System”) serves to transmit program identification and additional
services therefore also enabling automatic tracking of stations.
In the event of sufficiently satisfactory reception, the suitable RDS radio stations will
display the station name instead of the station frequency.
If a radio station sends addi tional information via the RDS function while a station is
being stored, it can occur that the name of the radio station is later displayed incor-
rectly in the preset list. In this case, the stored station name can be restored by selecting
the desired radio station, wait until the correct station name is displayed as radio text
then press the menu control button and a pop-up window is
displayed on the screen.Traffic programme function TPSwitching traffic programme TP (TMC Program) on or off– Press the function key in the RADIO mode.
– Briefly press on in the opening pop-up window to switch the traffic programme
function on or off.
ScanExtras
Dest. memory
1 ...
24 ...
SETUP
Delete presets
A10
All
A10
Fig. 6 Preset list
RADIO
Extras
Dest. memory
1
24
RADIO
Band
FM/List
A10
º
A10
Station name stored
Extras
TP
s34g.6.book Page 14 Thursday, January 14, 2010 8:48 AM

Range selector key RADIO15
The display “TP” in combination with a station name (e.g. in the station or preset list),
indicates a traffic programme station.
Irrespective of which radio st ation is heard, an additional receiver part in the unit
ensures that a traffic programme station can always be received as long as the traffic
programme function is switched on.
The functionality of the tr affic programme function “ TP” is displayed at the top right on
the touch-screen.
If no traffic programme station can be rece ived because, for example, radio reception
is interrupted in general, “ No TP” will be displayed instead of “ TP”. Remember that car
parks, tunnels, high building s or mountains can interrupt the radio signal up to the
total loss of reception.
Incoming traffic announcement
If you wish to interrupt the transmission of the traffic announcement, press on the
function key in the pop-up window Traffic announcement. The traffic informa-
tion function remains available and a following traffic announcement is replayed if a
random source is switched on. Pressing the function key will switch off the
traffic information function permanently.
Cancel
TP off
s34g.6.book Page 15 Thursday, January 14, 2010 8:48 AM