Introduction
10General operating informationIntroductionDue to changes to its settings, some aspects of the unit's operation may
differ from the descriptions given in this manual. For this reason, SEAT recom-
mends that you reset the unit to its factory settings the first time you use it
⇒ page 87.
Additional Information:•Safety notes
’ ⇒ page 6
•Unit overview ⇒page 8•Multifunction steering wheel, to change track or station ⇒Booklet
“Owner's Manual”, Section “Vehicle overview” Note
Lightly pressing the buttons or briefly pressing the touchscreen is sufficient
to operate the unit.
Note
Never press a button down for longer than 10 minutes. Otherwise the system
will interpret this as a malfunction ( button jammed).
Note
Due to country-specific legislation, certain functions cannot be selected on
the screen when the vehicle is travelling above a certain speed.
Note
Using a mobile telephone in the vehicle may cause noise from the vehicle
speakers.
Note
In some vehicles equipped with a parking distance warning system, the
volume of the current audio source is automatically lowered when reverse
gear is engaged.
Note
Restrictions on the use of devices using Bluetooth technology may be appli-
cable in some countries. Please ask your local authority for further
information.Switching on and offPress the rotary/push knob
D ⇒ page 8, fig. 1 briefly to manually switch
the unit on or off.
When the system is switched on, the sound source which was playing when
the unit was switched off will come on.
When the engine is off, the unit will automatically switch off after 30 minutes
(timeout).
Anti-theft code
The anti-theft code is stored in the vehicle once it has been entered (conven-
ience radio code). The anti-theft coding lock then only needs to be released
manually if the unit is installed in another vehicle. In such a case, a keypad
field and a prompt to enter the code will appear when the unit is switched on.
In this case, you should contact a SEAT dealer.
If the vehicle battery has been disconnected, switch on the ignition before re-
connecting the unit.
A1
MediaSystem2.1_EN.book Seite 10 Donnerstag, 29. April 2010 4:18 16
Settings (SETUP)
88Opening the Sound main menu•Press the unit button from any menu.•Press the function button at the bottom-left of the screen to open
the menu for changing sound and volume settings ⇒page 87, fig. 86.
The currently selected settings are indicated in the overview by the scale in
the circle
“ next to the respective menu item ⇒page 87, fig. 86 .
Changing the balance and fader settings
•Press the function buttons , or to open the respective
settings menus for adjusting the “tone” ⇒page 87, fig. 87 .•Turn the setting knob ⇒page 8, fig. 1 or press the function button
or to alter the current setting.•Press the function button or to open the settings menu for
changing the sound focus to the left or right (balance) or to the front or rear
(fader).•Turn the setting knob or press the appropriate function button to alter the
current setting.
Changing the volume settings and adjustments
The volume settings and adjustments can be pre-defined.
While you adjust volume settings, the currently active audio source is played
at the level of the setting as you change it.•In the Sound main menu , press the function button ⇒ page 87,
fig. 86 .•Press the function button ,
⇒ page 23, or
to open the corresponding settings menu.•Turn the setting knob or press the or function button.•Pressing the function button opens a pop-up window in
which you can set the automatic audio volume reduction applied when the
parking distance warning system is active. Functional description of speed-dependent volume adjustment (GALA)
The speed dependent volume adjustment automatically increases the
volume as the vehicle speed increases.
The degree to which the volume increases with speed is adjusted on a scale
between
1 and 7.
If a low value is set, the volume rises only slightly as the speed of the vehicle
increases. At a high setting the volume is increased more. At 0 speed-
dependent volume control is switched off (display: Off).
System settings•Press the unit button and the function button to open the
settings menu.
Resetting to factory settings
The restoration of the original settings deletes all the previous entries, desti-
nations and other settings .•In the System settings menu , press the function button.•Confirm the prompt by pressing to reset the unit to its original
settings.
Other system settings
SETUPSound
Treble
Mid
Bass
A10
€
Balance
FaderVol u m e
Max. switch-on volume
Traffic announcements (TP)
Navigation volume
Speed-dependent vol. adjustment
€
vol. reduction
Function button: Result
: Press to select the desired language for text and voice output.
ALTERNATIVELY: select to use the language programmed on
the instrument panel.
: The keyboard in input windows has an alphabetic layout.
SETUP
SystemFactory settings
Ye s
Language
Automatic
View of keyboardABC
MediaSystem2.1_EN.book Seite 88 Donnerstag, 29. April 2010 4:18 16
