2010 Seat Leon 5D window

Navigation69
The route list contains the names or designations of roads to be driven on
before each turning point. These are referred to below as “route sections”. All
route sections to be passed up to the next destination are displayed.
The list also shows the distance to be travelled along each route section and
the expected time required to reach the next turning point.•Turn the setting knob ⇒page 8, fig. 1 to view the route list.•Press the setting knob or Details function button to obtain more informa-
tion about a marked section in an additional information window.•Press the unit button to close the information window.
Display sections of route
The arrow
b behind an entr y in the route list indicates that more sections can
be displayed.
•Select the entry with the arrow
b by turning the setting knob and display
the sections of the route by pressing “Display”. The arrow changes to
a.
•Press the entry with the arrow
a to hide the sections of the route again.
Manually excluding sections in the route listThe sections of the journey which are marked can be excluded individually or
all together from the calculation in the route lists. Only one exclusion may be
entered at a time.•Displaying the route list ⇒ page 68.•Turn the setting knob ⇒page 8, fig. 1 to mark the first route section
of the stretch of route to be excluded.•Press the function button.
The item is marked as excluded and the function button changes to . If, instead of the button , appears in the route list, this
means that the section has already been excluded.
•Select the route section of the stretch of route you wish to exclude and
press the function button.
If the button is not active, the section to be excluded is too long.
(Max) is displayed on the bottom line of the screen after the excluded
distance.•Shorten the section of route to be excluded until the word (Max) disap-
pears and it is possible to select the function button. At the same
time, display partial sections of the route within a section of the route
⇒ page 69.
When an exclusion has been entered, the route list closes.
Route guidance will start again when the navigation system has calculated an
alternative route to the excluded section.
Re-opening a section•Press the unit button in any of the navigation menus (except SETUP).•In the information window , press the function button.•Press the function button in the pop-up window.•Alternatively:open the route list and press the function button.Note
Information on entering an exclusion starting from the current vehicle posi-
tion ⇒page 70.
Note
The excluded route section is displayed on the map ⇒page 65.
A10

A10
Exclude
Exclude to
Exclude to
Re-open
Exclude to
Exclude to
Exclude to
º
Route
Re-open section
Re-open
MediaSystem2.1_EN.book Seite 69 Donnerstag, 29. April 2010 4:18 16

Navigation
70Directly excluding a route section further ahead (congestion)During a route guidance, the route section of the remaining stretch of route
can be excluded manually.•Press the unit button in any of the navigation menus (except SETUP).•In the information window , press the function button.•Press the function button in the pop-up window.•Enter the length of the section to be excluded by turning the setting knob
⇒ page 8, fig. 1 .
The length indicated for the route section is shown on the lower line of the
screen. If (Max) is displayed, this indicates that the maximum permitted
length for exclusion has been reached.•Press the setting knob or function key to confirm the exclusion.
The excluded route section is displayed on the map.
Route guidance will start again when the navigation system has calculated an
alternative route to the excluded section.
Re-opening a section•Press the unit button in any of the navigation menus (except SETUP).•In the information window , press the function button.•Press the function button in the pop-up window.Note
It is also possible to enter or cancel an exclusion while viewing the TMC traffic
announcements using the function button ⇒ page 71.
Note
Information on manually excluding route sections further ahead
⇒page 69.Dynamic route guidance with TMC (Traffic Message Channel)The prerequisite for dynamic route guidance is always the reception of a TMC
traffic news station for the navigation area available in the unit. TMC traffic
reports received can be displayed in a list ⇒page 71.
If dynamic route guidance is activated, any TMC traffic reports are taken into
account in the route calculation.
Switching the dynamic navigation on or off•Press the unit button in one of the navigation menus.•In the Navigation setup menu , press the function button to
open the Route options setup menu ⇒ fig. 71 .
º
Route
Congestion aheadA10OK
º
Route
Re-open section
Congestion ahead
Fig. 71 Route options
setup menu.
SETUP
Route options
MediaSystem2.1_EN.book Seite 70 Donnerstag, 29. April 2010 4:18 16

Navigation
72The unit only processes and displays TMC traffic reports affecting the area
within a radius of roughly 100 km from the current vehicle position.
TMC traffic reports are required for dynamic route guidance and are displayed
on the map ⇒ page 70.
Display TMC traffic reports•Press the unit button to display the list of the current TMC traffic
reports ⇒page 71, fig. 72 .•Press one of the TMC traffic reports on the screen to open the detailed
view ⇒page 71, fig. 73 .•Alternatively: select the TMC report by turning the setting knob
⇒ page 8, fig. 1 and open the detailed view by pressing ⇒page 71,
fig. 73 .•In the detailed view, you can browse through the TMC traffic reports using
the function buttons and .
Display TMC traffic news stations•Open the list of the current TMC traffic reports.•Press the ⇒page 8, fig. 1 unit button to open the information
window. The current TMC traffic news station is displayed.•Press the unit button again to close the information window.Note
By using the ⇒ page 71, fig. 72 function button it is
possible to enter a manual exclusion from the vehicle position ⇒page 70.
Note
The radio-navigation system can only process and store TMC traffic reports if
the unit has access to navigation data for the area you are currently travelling
through.
Note
The quality of the dynamic route guidance depends on the information
contained in the TMC traffic reports. Th e radio stations are responsible for the
content of the news broadcast.Route guidance in demo modeIf demo mode is activated in the Navigation setup menu ⇒ page 73, an addi-
tional pop-up window opens when you start route guidance.•Pressing the function button starts a “virtual route guidance” to
the destination you have entered.•If you press the function button, a “real route guidance” starts.
The sequence of events and the operations in virtual route guidance are
similar to those in real route guidance.
Virtual route guidance is repeated when you reach the fictitious destination
and always starts again from the starting point if it is interrupted.
If the starting point for demo mode has been defined manually in the
Navigation setup menu , virtual route guidance will start from this position.
If the vehicle is moved and the unit can determine its current location by GPS,
any manually entered starting point will be overwritten with the current
vehicle location ⇒ page 73.
When real route guidance is started following virtual route guidance in demo
mode, the unit first has to reorient itself. This may take some time, depending
on the number of satellites the unit can currently receive. Moving the vehicle
may speed up the reorientation process.
TRAFFICA10Previous
Next
º
A7
ºCongestion ahead
DemoNormal
MediaSystem2.1_EN.book Seite 72 Donnerstag, 29. April 2010 4:18 16

Telephone control (Phone)
82•Press the function button.•Enter the name you are searching for in the input window.
Each time you enter a character, the sequence of characters in the input line
is automatically completed with a name that is in the address book.
If no name is offered when all the characters have been entered, there is no
entry in the address book corresponding to the sequence of characters you
have entered.•Delete characters in the line of data until a name is suggested.
Both upper and lower case are accepted when searching for an entry in the
address book.•Press the function button to select the entry in the address book
when you have found it.•Alternatively: press the right unit button to select the entry in the list,
when you have found it.•Press the selected address book entry to make a call.•Alternatively: press the setting knob ⇒page 8, fig. 1 to make the
call.Displaying and editing the phone numberA telephone number stored in the address book or in a call list can be
changed before you dial it.
Displaying and changing telephone numbers via an input window•Select the phone number and press the function button.•Press the function button to view the number in the input window.
The phone number can be changed here or reproduced as a DTMF sequence.
After you have changed the number, you can dial it by pressing the function
key . The changes
are not saved permanently in the address book. The modified
phone number can be viewed in the call list Numbers dialled after a call has
been made.
Call listsAll the call lists in the mobile phone memory can be consulted using the radio
and navigation system phone control system. The call lists give all the calls
made using the mobile phone.
If the phone accepts the handsfree profile 1.5 , calls not made through the
radio and navigation phone control system will also be shown.
Missed calls
The call list gives all missed and unanswered calls.
Numbers dialled
The call list gives all the phone numbers selected through the mobile phone
and through the radio and navigation phone control system.
SearchOK
A10
Details
Edit

Fig. 81 Call list.
MediaSystem2.1_EN.book Seite 82 Donnerstag, 29. April 2010 4:18 16

Telephone control (Phone)
84Using the telephoneAccepting, ending or rejecting a callWhen there is an incoming call, the phone number of the caller is displayed
on the radio and navigation screen.
If a phone number has been saved in the address book, the name stored
against the phone number is displayed instead of the number.
An incoming call can be accepted, ended or rejected using the radio and navi-
gation phone control system.•Press the function button to answer the call.•Press the function button to answer the call.•Press the function button to reject the call.Enter and call a phone number
It is possible to enter a phone number manually using the PHONE main menu.•Open the PHONE main menu by pressing the unit button.•In the PHONE main menu, press the function button ⇒page 79,
fig. 78.•Enter the required phone number in the input window by pressing the
characters.•After entering the complete phone number, press the function button
to make the call.Making a call from the address book•Open the address book in the PHONE main menu.•Select the required entry by turning the setting knob ⇒page 8, fig. 1 .•Press the setting knob to dial the number.•ALTERNATIVELY: Press the required entry to make the call.Making a call from the call list•Open the call list in the PHONE main menu.•Select the required entry in the list by turning the setting knob ⇒page 8,
fig. 1 .•Press the setting knob to dial the number.•ALTERNATIVELY: Press the required entry to make the call.•Alternatively: press the function button or the lower unit button to
make the call.
^^
Fig. 82 Enter a telephone
number.
PHONE
AA

A10
A10

MediaSystem2.1_EN.book Seite 84 Donnerstag, 29. April 2010 4:18 16

Telephone control (Phone)85
During a phone callActive connection display
During a phone call, the number of the caller and the length of the conversa-
tion are displayed on the screen.
If the phone number has been saved in the address book, the name allocated
to the number is displayed instead of the number.
Muting the call
To prevent the caller listening to conversations inside the car during an active
connection, the sound transfer to the other phone can be temporarily discon-
nected.•Press the button with a connection established.•Press the function button in the pop-up window to disconnect
sound transmission to the other caller.•Press the function button again in the pop-up window to restore
sound transmission to the other caller.
Accepting and holding an additional callAn additional call may be accepted during a telephone conversation. It is
possible to switch between calls.
Call notification: Accept additional incoming call•If you receive another call while you are talking on the phone, the phone
number or name of the caller is displayed on the screen. The display “ ...
calling ” is also shown•To reject the second caller, press the function button .•ALTERNATIVELY: Press the left unit button.•To accept the second call, press directly on the call notification, or the
function button .•ALTERNATIVELY: Press the right unit button.
If you accept the second call, the first caller is put on hold, but the connection
is not cut off (display: “ Hold call”).
Fig. 83 Display an active
connection.
ExtrasMuteMute
Fig. 84 Call notification.^

MediaSystem2.1_EN.book Seite 85 Donnerstag, 29. April 2010 4:18 16

Telephone control (Phone)
86Alternating: Alternating between two calls•To alternate between two calls, press the call display for the caller you
wish to talk to.•Alternatively: press the function button and, in the pop-up
window, the function button.
While one of the callers is connected, the other caller will be kept on hold.•To end an active connection with a caller, press the function button .•ALTERNATIVELY: Press the left unit button.
During an active conversation it is only possible to place one other caller on
hold at the same time.Note
The “Call notification” function must be activated on the mobile phone.
Note
The behaviour of the “Alternate” function will depend on the handsfree
profile version One requirement for the above functions is compatibility with
HFP 1.5 .
Making a conference callOne caller “on hold” can be included in the active conversation, to make a
conference call.
Adding several callers to a conference call
All the callers in the conference are able to hear and speak to the other
callers.•Press the function button and the function button in
the pop-up window to add both callers to the conference call.
Both callers are shown in line on the screen as “ Conference callers”.
An additional incoming call may be accepted during a telephone conference.
It is possible to alternate between the conference and the new call, or the new
caller can be invited to join the conference. Depending on the provider, the
conference call may include up to six callers.•Press the function button to end the conference call and separate the
connection with all the callers.
Extras
Alternate calls
^
Fig. 85 Adding several
callers to a teleconfer-
ence.
Extras
Conference
^
MediaSystem2.1_EN.book Seite 86 Donnerstag, 29. April 2010 4:18 16

Settings (SETUP)
88Opening the Sound main menu•Press the unit button from any menu.•Press the function button at the bottom-left of the screen to open
the menu for changing sound and volume settings ⇒page 87, fig. 86.
The currently selected settings are indicated in the overview by the scale in
the circle
“ next to the respective menu item ⇒page 87, fig. 86 .
Changing the balance and fader settings
•Press the function buttons , or to open the respective
settings menus for adjusting the “tone” ⇒page 87, fig. 87 .•Turn the setting knob ⇒page 8, fig. 1 or press the function button
or to alter the current setting.•Press the function button or to open the settings menu for
changing the sound focus to the left or right (balance) or to the front or rear
(fader).•Turn the setting knob or press the appropriate function button to alter the
current setting.
Changing the volume settings and adjustments
The volume settings and adjustments can be pre-defined.
While you adjust volume settings, the currently active audio source is played
at the level of the setting as you change it.•In the Sound main menu , press the function button ⇒ page 87,
fig. 86 .•Press the function button ,
⇒ page 23, or
to open the corresponding settings menu.•Turn the setting knob or press the or function button.•Pressing the function button opens a pop-up window in
which you can set the automatic audio volume reduction applied when the
parking distance warning system is active. Functional description of speed-dependent volume adjustment (GALA)
The speed dependent volume adjustment automatically increases the
volume as the vehicle speed increases.
The degree to which the volume increases with speed is adjusted on a scale
between
1 and 7.
If a low value is set, the volume rises only slightly as the speed of the vehicle
increases. At a high setting the volume is increased more. At 0 speed-
dependent volume control is switched off (display: Off).
System settings•Press the unit button and the function button to open the
settings menu.
Resetting to factory settings
The restoration of the original settings deletes all the previous entries, desti-
nations and other settings .•In the System settings menu , press the function button.•Confirm the prompt by pressing to reset the unit to its original
settings.
Other system settings
SETUPSound
Treble
Mid
Bass
A10

€
Balance
FaderVol u m e
Max. switch-on volume
Traffic announcements (TP)
Navigation volume
Speed-dependent vol. adjustment

€
vol. reduction
Function button: Result
: Press to select the desired language for text and voice output.
ALTERNATIVELY: select to use the language programmed on
the instrument panel.
: The keyboard in input windows has an alphabetic layout.
SETUP
SystemFactory settings
Ye s
Language
Automatic
View of keyboardABC
MediaSystem2.1_EN.book Seite 88 Donnerstag, 29. April 2010 4:18 16