2010 RENAULT SCENIC wiring

13B-184
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault
memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$170.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
PR064COOLANT TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the engine coolant temperature in °C.
NOTESSpecial note:
Default value: 80 °C.
Conformity check: Engine stopped and ignition on, or engine running and engine coolant
temperature > 80
°C
Cold, PR064 = ambient temperature.
Check the condition of the coolant temperature sensor connections.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
If necessary, replace the coolant temperature sensor (see MR 417 Mechanical systems, 19A, Cooling,
Coolant temperature sensor: Removal - Refitting).
Measure the resistance between connections 3C and 3JK of component 244.
If the resistance of the coolant temperature sensor is not:
(theoretical values)
at – 40
°C: 68780 Ω < X < 82780 Ω
at – 10
°C: 11332 Ω < X < 13588 Ω
at 25
°C: 2140 Ω < X < 2364 Ω
at 50
°C: 772 Ω < X < 850 Ω
at 80
°C: 275 Ω < X < 291 Ω
at 110
°C: 112 Ω < X < 118 Ω
at 120
°C: 86 Ω < X < 90 Ω,
Replace the coolant temperature sensor, component code 244 (see MR 364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 19A, Cooling,
Coolant temperature sensor: Removal - Refitting).
DCM1.2_V48_PR064/DCM1.2_V4C_PR064/DCM1.2_V50_PR064/DCM1.2_V54_PR064/DCM1.2_V58_PR064/DCM1.2_V5C_PR064

13B-192
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault
memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$170.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
PR132AIR FLOW
PARAMETER
DEFINITIONThis parameter indicates the inlet air flow in mg/st.
NOTESSpecial notes:
For vehicles that are not equipped with a flowmeter, the air flow is estimated using
the following parameters:
–Inlet air temperature,
–The atmospheric pressure,
–The EGR valve position,
–The fuel flow,
–The engine speed.
There must be no faults present.
Perform this fault finding procedure:
–after finding an inconsistency in the parameter,
–or after a customer complaint (lack of power, smoke etc.).
See the Wiring diagrams Technical Note for the vehicle.
Conformity check with engine stopped and ignition on.
Indicates the inlet air flow PR132 ≈ 0 mg/st.
Conformity check: Engine running at idle speed and engine coolant temperature > 80
°C
Indicates the inlet air flow PR132 ≈ 200 mg/st.
DCM1.2_V48_PR132/DCM1.2_V4C_PR132/DCM1.2_V50_PR132/DCM1.2_V54_PR132/DCM1.2_V58_PR132/DCM1.2_V5C_PR132

13B-198
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault
memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$170.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
PR730AIR FLOW SENSOR TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the air temperature of the flowmeter in °C.
NOTESSpecial notes:
Depending on the engine type, the air temperature is given by the air flowmeter or the
exterior air temperature sensor.
Conformity check: Engine stopped and ignition on, or engine running and engine coolant
temperature > 80
°C
Check the condition of the air flow sensor connections.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
If necessary, replace the sensor (see MR 364 (Mégane II), MR 370 (Scénic II), MR 385 (Modus), MR 392 (Clio III),
MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 12A, Fuel mixture, Air flowmeter: Removal -
Refitting).
Measure the resistance between the following connections:
(vehicle with flowmeter)
–3B and 3DW of component 799;
(vehicle without flowmeter)
–3PB and 3KQ of component 272,
–3SH and 3KQ of component 272,
–3JQ and 3KQ of component 272.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
DCM1.2_V48_PR730/DCM1.2_V4C_PR730/DCM1.2_V50_PR730/DCM1.2_V54_PR730/DCM1.2_V58_PR730/DCM1.2_V5C_PR730

13B-221V10 MR-372-J84-13B100$190.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
TEST 10
CONTINUED 2
Visual inspection of the electrical connector of the solenoid valve
Switch off the engine.
Note:
The requested checks are only visual.
1. Check that the connector is correctly connected and locked.
2. Check the absence of damage to the electric wires where they leave the insulation.
Disconnect the connector to continue the checks.
3. Check the absence of thermal damage to the unit and mechanical damage to the lock.
4. Check the absence of deformations of the contacts (clips and tabs).
5. Check the sealing of the connector.
Do the visual inspections show any damage?
Refer to Technical Note 6015A, Repairing electrical wiring.
B
NO
YES
A
C

13B-233V10 MR-372-J84-13B100$190.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
TEST 14 Accelerator pedal check
Can the accelerator pedal be fully
depressed and does it return fully?Check that there are no obstructions between the floor
and the accelerator pedal, and check that the latter has no
points of resistance.
Vehicle under + after ignition feed.
Measure the voltage between
connections 3LR and 3LT of
component 921.Check the continuity and insulation of connections 3LR
and 3LT between components 921 and 120.
If the connection is faulty and there is a repair method
(see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring,
otherwise replace it. Expected result:
4.75 V < X < 5.25 V
Vehicle under + after ignition feed.
Fully depress the accelerator pedal
and measure the voltage between
connections 3LS and 3LT of
component 921.Check the continuity and insulation of connection 3LS
between components 921 and 120.
If the connection is faulty and there is a repair method
(see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If these checks are correct, replace the accelerator pedal
sensor (see MR 392 (Clio III), MR 364 (Mégane II), MR 370
(Scénic II), MR 417 (Kangoo 2), Mechanical, 37A,
Mechanical component controls, Accelerator pedal:
Removal – Refitting) or (see MR 385 (Modus), MR 411
(New Twingo), Mechanical, 37A, Mechanical
component controls, Accelerator brake pedal
assembly: Removal – Refitting). Expected result:
3.94 < X < 4.56 V
Vehicle under + after ignition feed.
Accelerator pedal in no load position,
measure the voltage between
connections 3LS and 3LT of
component 921.Replace the accelerator pedal sensor (see MR 392
(Clio III), MR 364 (Mégane II), MR 370 (Scénic II), MR 417
(Kangoo 2), Mechanical, 37A, Mechanical component
controls, Accelerator pedal: Removal – Refitting)
or (see MR 385 (Modus), MR 411 (New Twingo),
Mechanical, 37A, Mechanical component controls,
Accelerator brake pedal assembly: Removal –
Refitting). Expected result:
0.66 V < X < 0.84 VNO
YES
NO
YES
NO
YES
NO
YES
A
DCM1.2_V48_TEST14/DCM1.2_V4C_TEST14/DCM1.2_V50_TEST14/DCM1.2_V54_TEST14/DCM1.2_V58_TEST14/DCM1.2_V5C_TEST14

13B-234V10 MR-372-J84-13B100$190.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
TEST 14
CONTINUED
Vehicle under + after ignition feed.
Measure the voltage between
connections 3LU and 3LV of
component 921.Check the continuity and insulation of connections 3LU
and 3LV between components 921 and 120.
If the connection is faulty and there is a repair method
(see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring,
otherwise replace it. Expected result:
4.75 V < X < 5.25 V
Vehicle under + after ignition feed. Fully
depress the accelerator pedal
and measure the voltage between
connections 3LW and 3LV of
component 921.Check the continuity and insulation of connection 3LW
between components 921 and 120.
If the connection is faulty and there is a repair method
(see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If these checks are correct, replace the accelerator pedal
sensor (see MR 392 (Clio III), MR 364 (Mégane II), MR 370
(Scénic II), MR 417 (Kangoo 2), Mechanical, 37A,
Mechanical component controls, Accelerator pedal:
Removal – Refitting) or (see MR 385 (Modus), MR 411
(New Twingo), Mechanical, 37A, Mechanical component
controls, Accelerator brake pedal assembly: Removal –
Refitting). Expected result:
2.16 < X < 2.38 V
Vehicle under + after ignition feed.
Accelerator pedal in no load position,
measure the voltage between
connections 3LW and 3LV of
component 921.Replace the accelerator pedal sensor (see MR 392
(Clio III), MR 364 (Mégane II), MR 370 (Scénic II), MR 417
(Kangoo 2), Mechanical, 37A, Mechanical component
controls, Accelerator pedal: Removal – Refitting) or
(see MR 385 (Modus), MR 411 (New Twingo),
Mechanical, 37A, Mechanical component controls,
Accelerator brake pedal assembly: Removal –
Refitting). Expected result:
0.32 < X < 0.42 V
Contact the Techline
A
NO
YES
NO
YES
NO
YES

13B-237V10 MR-372-J84-13B100$210.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ALP2 The engine will not start
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Check that the fuel tank is correctly filled and that the fuel is correct: run TEST 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.
Check the air inlet circuit: run TEST 5 Air inlet circuit check.

Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR
364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III), MR
411 (New Twingo), MR 417 (Kangoo 2),
Mechanical, 19B, Exhaust, Catalytic
converter: Removal - Refitting).
Check the electrical circuit: run TEST 2 Electrical circuit check.
Check the electrical conformity of the heater plugs (the resistance value of the heater plug must be less
than 2 Ω).

Is the timing set correctly? Carry out the necessary repairs.
Visually check the condition of the engine wiring harness.
YES
NO
NO
YES
A
DCM1.2_V48_ALP2/DCM1.2_V4C_ALP2/DCM1.2_V50_ALP2/DCM1.2_V54_ALP2/DCM1.2_V58_ALP2/DCM1.2_V5C_ALP2

13B-239V10 MR-372-J84-13B100$210.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ALP2
CONTINUED 2
Visually check that there are no leaks on the high pressure circuit: run TEST 7 High pressure circuit sealing
check.
Check the high pressure system: run TEST 6 High pressure system check.
Check the computer:
Check that the computer connectors are properly locked.
Check the condition of the computer connections (bent pin, signs of corrosion, silicone, etc.).
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Contact the Techline if the customer complaint is still present.
B