2010 PONTIAC G5 height adjustment

4. Push the latch plate into the buckle until it clicks.Pull up on the latch plate to make sure it is secure.
If the belt is not long enough, see Safety Belt
Extender on page 2-31 .
Position the release button on the buckle so that
the safety belt could be quickly if necessary.
5. If equipped with a shoulder belt height adjuster, move it to the height that is right for you. See
“Shoulder Belt Height Adjustment” later in this
section for instructions on use and important safety
information. 6. To make the lap part tight, pull up on the
shoulder belt.
It may be necessary to pull stitching on the safety
belt through the latch plate to fully tighten the
lap belt on smaller occupants.
2-26

To unlatch the belt, push the button on the buckle. The
belt should return to its stowed position.
Before a door is closed, be sure the safety belt is out of
the way. If a door is slammed against a safety belt,
damage can occur to both the belt and the vehicle.
Shoulder Belt Height Adjuster
(Sedan Only)
The vehicle has a shoulder belt height adjuster for the
driver and right front passenger position.
Adjust the height so that the shoulder portion of the belt
is centered on the shoulder. The belt should be away
from the face and neck, but not falling off the shoulder.
Improper shoulder belt height adjustment could
reduce the effectiveness of the safety belt in a crash.Press the release
button (A) and move the
height adjuster to the
desired position. The
adjuster can be moved up
by pushing up on the
shoulder belt guide.
After the height adjuster is set to the desired position,
try to move it down without pressing the release
button to make sure it has locked into position.
2-27

Properly torqued wheel nuts are necessary to help
prevent brake pulsation. When tires are rotated, inspect
brake pads for wear and evenly tighten wheel nuts in
the proper sequence to torque specifications in
Capacities and Specications on page 6-109.
If the vehicle has rear drum brakes, they do not have
wear indicators, but if a rear brake rubbing noise is heard,
have the rear brake linings inspected immediately. Rear
brake drums should be removed and inspected each time
the tires are removed for rotation or changing. When the
front brake pads are replaced, have the rear brakes
inspected, too.
Brake linings should always be replaced as complete
axle sets.
Brake Pedal Travel
See your dealer/retailer if the brake pedal does not
return to normal height, or if there is a rapid increase in
pedal travel. This could be a sign that brake service
might be required.
Brake Adjustment
Every moderate brake stop, the disc brakes adjust for
wear. If rarely making moderate or heavier brake stops,
the brakes might not adjust correctly. Very carefully
making a few moderate brake stops about every
1,000 miles (1 600 km) will adjust the brakes properly.
If the vehicle has rear drum brakes and the brake pedal
goes down farther than normal, the rear drum brakes
might need adjustment. Adjust them by backing up and
firmly applying the brakes a few times.
Replacing Brake System Parts
The braking system on a vehicle is complex. Its many
parts have to be of top quality and work well together if
the vehicle is to have really good braking. The vehicle
was designed and tested with top-quality brake parts.
When parts of the braking system are replaced — for
example, when the brake linings wear down and new
ones are installed — be sure to get new approved
replacement parts. If this is not done, the brakes might
not work properly. For example, if someone puts in brake
linings that are wrong for the vehicle, the balance
between the front and rear brakes can change — for the
worse. The braking performance expected can change in
many other ways if the wrong replacement brake parts
are installed.
6-32

3. At the wall, measure from the ground upward (A) tothe recorded distance from Step 2 and mark it.
4. Draw or tape a horizontal line (B) on the wall the width of the vehicle at the height of the mark in
Step 3.
Notice: Do not cover a headlamp to improve beam
cut-off when aiming. Covering a headlamp may
cause excessive heat build-up which may cause
damage to the headlamp.
5. Turn on the low-beam headlamps and place a piece of cardboard in front of the headlamp not
being adjusted. Do not place it directly on the
headlamp. This allows only the beam of light from
the headlamp being adjusted to be seen on the
flat surface. 6. Locate the vertical headlamp aiming screws, which
are under the hood near each headlamp assembly.
The adjustment screw can be turned with a 6 mm
socket wrench.
7. Turn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line. Turn it
clockwise or counterclockwise to raise or lower the
angle of the beam.
6-40

Folding Rear Seat............................................ 2-9
Fuel ............................................................... 6-5
Additives ...................................................... 6-6
California Fuel .............................................. 6-6
Filling a Portable Fuel Container ....................6-10
Filling the Tank ............................................. 6-8
Fuels in Foreign Countries .............................. 6-7
Gage ......................................................... 4-34
Gasoline Octane ........................................... 6-6
Gasoline Specifications .................................. 6-6
Fuel Economy Driving for Better ......................................... 1-21
Fuses Engine Compartment Fuse Block .................6-105
Floor Console Fuse Block ...........................6-103
Fuses and Circuit Breakers .........................6-103
Windshield Wiper ....................................... 6-102
G
Gages
Fuel .......................................................... 4-34
Speedometer .............................................. 4-21
Tachometer ................................................. 4-21
Gasoline Octane ........................................................ 6-6
Specifications ............................................... 6-6
Glove Box ..................................................... 3-36
GM Mobility Reimbursement Program .................. 8-7
H
Halogen Bulbs................................................ 6-41
Hazard Warning Flashers ................................... 4-3
Head Restraints ............................................... 2-7
Headlamp Wiring ........................................... 6-102
Headlamps ...................................................... 4-9
Aiming ....................................................... 6-38
Bulb Replacement ....................................... 6-41
Daytime Running Lamps (DRL) .....................4-10
Flash-to-Pass ............................................... 4-5
Headlamps, Front Turn Signal, Sidemarker, and Parking Lamps .................................. 6-42
High/Low Beam Changer ................................ 4-5
On Reminder .............................................. 4-10
Range Adjustment ......................................... 2-7
Wiper Activated ........................................... 4-10
Heated Seats ................................................... 2-4
Heater ........................................................... 4-14
Engine Coolant ........................................... 3-23
Height Adjuster, Driver Seat ............................... 2-3
Highbeam On Light ......................................... 4-34
Highway Hypnosis ........................................... 5-19
Hill and Mountain Roads .................................. 5-20
Hood Checking Things Under ................................6-10
Release ..................................................... 6-11
6