2010 PEUGEOT 807 ignition
[x] Cancel search: ignitionPage 40 of 237
42
Starting and stopping
STARTING AND STOPPING
STOP position: steering lock.
The ignition is off.
Good practice when starting Handbrake
I f y o u r v e h i c l e i s fi t t e d w i t h a
version with a rotating front seat,
t h e h a n d b r a k e c a n b e d i s e n g a g e d .
P u l l i n g t h e h a n d b r a k e t o i m m o b i l i s e
the vehicle then lowering the lever
d o e s n o t r e l e a s e t h e b r a k e , i t p e r m i t s
rotation of the driver’s seat.
P u l l t h e b u t t o n p l a c e d a t t h e e n d o f t h e
h a n d b r a k e f o r w a r d s .
T h e h a n d b r a k e l e v e r l o w e r s .
You can now rotate the seat.
To return to normal operation, pull the
lever up until it clicks.
I f t h e h a n d b r a k e i s o n o r h a s
n o t b e e n r e l e a s e d f u l l y , t h i s i s
i n d i c a t e d b y :
- a warning light which comes
on on the instrument panel,
- a n a u d i b l e s i g n a l ,
- a message on the display.
Key
Take care not to place the key in
contact with grease, dust, rain or a
damp environment.
A h e a v y o b j e c t a t t a c h e d t o t h e k e y
(key ring, ...) weighing down on the
shaft of the key in the ignition switch
may cause a malfunction.
Running and accessories position.
C e r t a i n a c c e s s o r i e s c a n b e u s e d .
Starting position.
The starter is operated. Diesel pre-heating warning
light
Turn the key to the Running
position.
In cold weather, wait for this warning
light to switch off then operate the
starter (Starting position) until the
engine starts.
If the temperature is high enough, the
warning light comes on for less than
one second, you can start without
waiting. Good practice when stopping
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
t h e t u r b o c h a r g e r t o r e t u r n t o i d l e .
Do not press the accelerator when
switching off the ignition.
There is no need to engage a gear
after parking the vehicle.
Page 45 of 237
Steering wheel controls
4 6
WINDSCREEN WIPER STALK
Manual windscreen wipers Special position of the
windscreen wipers
In the minute following switching
o f f o f t h e i g n i t i o n , a n y a c t i o n o n t h e
stalk positions the wipers against the
w i n d s c r e e n u p r i g h t s .
This action enables you to position
t h e w i p e r b l a d e s f o r w i n t e r p a r k i n g ,
cleaning or replacement. Vehicle fitted with the
automatic windscreen
wipers control
D o n o t c o v e r t h e r a i n s e n s o r l o c a t e d i n
the centre of the fascia.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h
t h i s c o n t r o l , i n t h e AUTO p o s i t i o n ,
t h e w i n d s c r e e n w i p e r s o p e r a t e
a u t o m a t i c a l l y a n d adapt their speed
to the intensity of the rainfall .
When not in AUTO m o d e , f o r t h e
o t h e r p o s i t i o n s , r e f e r t o t h e m a n u a l
w i n d s c r e e n w i p e r s s e c t i o n .
The command must be reactivated
whenever the ignition has been
switched off for more than one
minute:
- m o v e t h e s t a l k t o a n y p o s i t i o n ,
- t h e n m o v e i t b a c k t o t h e r e q u i r e d position.
2 F a s t w i p e ( h e a v y r a i n ) .
1 N o r m a l w i p e ( m o d e r a t e r a i n ) .
l Intermittent wipe.
0 Off.
Single wipe
( p r e s s d o w n w a r d s ) . Refer to the "Changing a
w i n d s c r e e n w i p e r b l a d e " s e c t i o n o f
chapter 7.
Wash-wipe and headlamp wash
P u l l t h e s t a l k t o w a r d s y o u , t h e w a s h -
w i p e i s a c c o m p a n i e d b y a t i m e d s w e e p
of the wipers.
I f y o u r v e h i c l e i s fi t t e d w i t h t h i s
f u n c t i o n , t h e h e a d l a m p w a s h i s l i n k e d
w i t h t h e w a s h - w i p e , i t i s t r i g g e r e d i f t h e
d i p p e d h e a d l a m p s a r e o n . To park the wipers in their normal
p o s i t i o n a f t e r t h i s h a s b e e n d o n e ,
s w i t c h o n t h e i g n i t i o n a n d m o v e t h e
stalk.
T o t o p u p t h e l e v e l s , r e f e r t o t h e
" L e v e l s " s e c t i o n o f c h a p t e r 6 .
In the I n t e r m i t t e n t p o s i t i o n , t h e w i p i n g
s p e e d i s i n p r o p o r t i o n t o t h e v e h i c l e
s p e e d .
Page 49 of 237
Steering wheel controls
5 0
Switching the function off
- P l a c e t h e d i a l i n p o s i t i o n 0 or switch
off the ignition to switch everything
off. Good practice
W h e n c h a n g i n g t h e p r o g r a m m e d
r e f e r e n c e s p e e d b y m e a n s o f a
m a i n t a i n e d p r e s s , p a y a t t e n t i o n a s
t h e s p e e d c a n i n c r e a s e o r d e c r e a s e
r a p i d l y .
Do not use the cruise control on
s l i p p e r y r o a d s o r i n h e a v y t r a f fi c .
I n t h e e v e n t o f a s t e e p s l o p e , t h e c r u i s e
control cannot prevent the vehicle from
e x c e e d i n g t h e p r o g r a m m e d s p e e d .
I n a n y e v e n t , t h e c r u i s e c o n t r o l c a n n o t
r e p l a c e t h e n e e d t o o b s e r v e t h e s p e e d
l i m i t s , n o r c a n i t r e p l a c e t h e n e e d f o r
v i g i l a n c e a n d r e s p o n s i b i l i t y o n t h e p a r t
o f t h e d r i v e r .
Y o u a r e a d v i s e d t o k e e p y o u r f e e t n e a r
t h e p e d a l s .
T o a v o i d a n y j a m m i n g u n d e r t h e
p e d a l s :
- e n s u r e t h a t t h e m a t a n d i t s fi x i n g s
o n t h e fl o o r a r e p o s i t i o n e d c o r r e c t l y ,
- never place one mat on top of another.
Changing the
programmed speed
T h e r e a r e t w o m e t h o d s
of memorising a
s p e e d h i g h e r t h a n t h e
previous one:
Without using the accelerator:
- press the Set + button.
A b r i e f p r e s s i n c r e a s e s t h e s p e e d b y
1 m p h ( k m / h ) .
A m a i n t a i n e d p r e s s i n c r e a s e s t h e
s p e e d i n s t e p s o f 5 m p h ( k m / h ) .
Operating fault
T h e p r o g r a m m e d s p e e d i s c l e a r e d a n d
t h e d a s h e s fl a s h f o r a f e w s e c o n d s .
C o n s u l t a P E U G E O T d e a l e r t o h a v e
t h e s y s t e m c h e c k e d .
Using the accelerator:
- e x c e e d t h e m e m o r i s e d s p e e d u n t i l
t h e s p e e d r e q u i r e d i s r e a c h e d ,
- press the Set + or Set - button.
T o m e m o r i s e a s p e e d l o w e r t h a n t h e
previous one:
- press the Set - button.
A b r i e f p r e s s d e c r e a s e s t h e s p e e d b y
1 m p h ( k m / h ) .
A m a i n t a i n e d p r e s s d e c r e a s e s t h e
s p e e d i n s t e p s o f 5 m p h ( k m / h ) . Cancelling the programmed
reference speed
W h e n t h e v e h i c l e b e c o m e s s t a t i o n a r y ,
a f t e r s w i t c h i n g o f f t h e i g n i t i o n , t h e
s y s t e m n o l o n g e r m e m o r i s e s a s p e e d .
Page 52 of 237
Steering wheel controls
ERGONOMICS and COMFORT
3
53
Switching the function off
- P l a c e t h e d i a l i n p o s i t i o n 0 or switch
off the ignition to switch the system
o f f . T h e l a s t p r o g r a m m e d s p e e d
remains in the memory.
Exceeding the programmed
speed
P r e s s i n g t h e a c c e l e r a t o r p e d a l i n o r d e r
t o e x c e e d t h e p r o g r a m m e d s p e e d
will have no effect unless you press
t h e p e d a l
fi r m l y b e y o n d t h e point of
resistance .
T h e l i m i t e r i s d e a c t i v a t e d t e m p o r a r i l y
a n d t h e p r o g r a m m e d s p e e d fl a s h e s .
T o r e t u r n t o t h e l i m i t e r f u n c t i o n , r e d u c e
y o u r s p e e d t o b e l o w t h e p r o g r a m m e d
s p e e d . Operating fault
T h e p r o g r a m m e d s p e e d i s c l e a r e d a n d
t h e d a s h e s fl a s h f o r a f e w s e c o n d s .
C o n t a c t a P E U G E O T d e a l e r t o h a v e
t h e s y s t e m c h e c k e d .
Flashing of the speed
T h e s p e e d fl a s h e s :
- following forcing of the accelerator p o i n t o f r e s i s t a n c e ,
- when the limiter cannot prevent an i n c r e a s e i n t h e v e h i c l e s p e e d d u e
t o t h e p r o fi l e o f t h e r o a d o r o n a
s t e e p d e s c e n t ,
- in the event of sharp acceleration. Good practice
I n a n y e v e n t , t h e s p e e d l i m i t e r c a n n o t
r e p l a c e t h e n e e d t o o b s e r v e s p e e d l i m i t s ,
n o r c a n i t r e p l a c e t h e n e e d f o r v i g i l a n c e
a n d r e s p o n s i b i l i t y o n t h e p a r t o f t h e d r i v e r .
A l w a y s p a y a t t e n t i o n t o t h e p r o fi l e o f t h e
r o a d , t a k e c a r e o n s h a r p a c c e l e r a t i o n a n d
stay in complete control of your vehicle.
T o a v o i d a n y j a m m i n g u n d e r t h e
p e d a l s :
- e n s u r e t h a t t h e m a t a n d i t s fi x i n g s p o s i t i o n e d c o r r e c t l y ,
- never place one mat on top of another.
Page 62 of 237
ERGONOMICS and COMFORT
3
6 3
Seats
Memorising seat positions
T w o d r i v i n g p o s i t i o n s c a n b e
m e m o r i s e d , u s i n g buttons M/1 a n d
M/2 .
T h e s e a r e l o c a t e d o n t h e s i d e o f t h e
seat:
- Place the ignition key in the " r u n n i n g " p o s i t i o n ( 2 n d n o t c h ) ,
- A d j u s t y o u r s e a t ,
- Press button M , t h e n b u t t o n 1 for
a fi r s t d r i v i n g p o s i t i o n w i t h i n f o u r
s e c o n d s .
Repeat the same actions on buttons M
a n d 2 t o s t o r e a n o t h e r d r i v i n g p o s i t i o n .
A n a u d i b l e s i g n a l c o n fi r m s t h a t a
p o s i t i o n h a s b e e n m e m o r i s e d .
Memorising a new position cancels the
previous one. Activating a memorised driving
position
Front heated seat controls
W h e n t h e e n g i n e i s r u n n i n g , t h e f r o n t
s e a t s c a n b e h e a t e d s e p a r a t e l y .
U s e t h e a d j u s t m e n t c o n t r o l s l o c a t e d o n
t h e s i d e o f e a c h f r o n t s e a t t o s w i t c h o n
a n d s e l e c t t h e s e l f - r e g u l a t e d l e v e l o f
heating:
1: Low.
2: M e d i u m .
3: High.
0: Off.
A f t e r r e c a l l i n g a m e m o r i s e d
p o s i t i o n fi v e t i m e s i n s u c c e s s i o n ,
t h e f u n c t i o n w i l l b e c a n c e l l e d u n t i l
t h e e n g i n e i s s t a r t e d .
Engine running
- Keep button 1 or 2 p r e s s e d d o w n
u n t i l t h e e n d o f s e t t i n g o f t h e
c o r r e s p o n d i n g m e m o r i s e d p o s i t i o n .
Engine off
- B r i e fl y p r e s s b u t t o n
1 or 2 to recall
t h e c o r r e s p o n d i n g m e m o r i s e d
position.
Page 82 of 237
ERGONOMICS and COMFORT
3
8 3
Mirrors and windows
ELECTRIC WINDOWS
4. Rear left electric window switch.
5. Rear electric windows disarming
switch (child safety).
- r e d s t r i p v i s i b l e : t h e r e a r s w i t c h e s a r e a c t i v a t e d .
- r e d s t r i p c o v e r e d : t h e r e a r s w i t c h e s a r e d i s a r m e d . Y o u h a v e t w o o p t i o n s :
The electrical functions of the
e l e c t r i c w i n d o w s a r e d i s a r m e d
one minute after switching off the
ignition.
Disarming the rear controls
F o r t h e s a f e t y o f y o u r c h i l d r e n , p r e s s
switch 5 t o d i s a r m a l l o f t h e e l e c t r i c a l
controls in the rear:
- e l e c t r i c w i n d o w s ,
- s l i d i n g s i d e d o o r s ,
- sunroofs.
1. Driver's electric window switch.
2. Passenger electric window
switch.
3. Rear right electric window
switch. Manual operation:
- press or pull switch
1 , w i t h o u t g o i n g
b e y o n d t h e p o i n t o f r e s i s t a n c e . T h e
w i n d o w s t o p s w h e n t h e s w i t c h i s
r e l e a s e d .
Automatic operation:
- press or pull switch 1 , b e y o n d t h e
p o i n t o f r e s i s t a n c e : t h e w i n d o w
opens or closes completely when
t h e s w i t c h i s r e l e a s e d . P r e s s i n g t h e
switch again stops the movement
o f t h e w i n d o w .
Page 86 of 237
86
Driving safety
HANDBRAKE
HAZARD WARNING LIGHTS
Press the button, the direction
i n d i c a t o r s fl a s h .
They can operate with the ignition off.
Automatic lighting of hazard
warning lights
Equipment conditioned according
to country: when braking in an
emergency, depending on the
deceleration, the hazard warning lights
come on automatically. They switch
o f f a u t o m a t i c a l l y t h e fi r s t t i m e y o u
accelerate.
It is also possible to switch them off by
pressing the button.
DRIVING SAFETY
Applying
When parking, pull the handbrake to
immobilize your vehicle. When parking
on a slope, direct your wheels towards
the pavement and pull the handbrake.
Releasing
Pull on the handle and press the button
to release the handbrake. Pull the button located at the end of the
handbrake forwards.
The handbrake lever lowers.
You can now pivot the seat.
To return to normal operation, pull the
lever upwards until a click is heard.
If the handbrake is still on or has
not been released properly, this is
indicated by:
Disengaging
I f y o u r v e h i c l e i s fi t t e d w i t h a v e r s i o n
with a rotating front seat, apply the
handbrake. a warning light which comes
on on the instrument panel,
an audible signal,
a message on the display.
Page 89 of 237
SAFETY
89
Driving safety
4
TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP)
Activation of the ASR and ESP
systems
When the ignition is on, the ASR and
ESP systems are always active. Disarming the ASR/ESP systems
In certain conditions (vehicle stuck in
mud or snow, or on loose ground...), it
could prove useful to disarm the ASR
and ESP systems to make the wheels
spin and regain grip.
Press the switch, situated under the
steering wheel on the right of the
fascia.
The indicator light comes on
accompanied by a message:
the ESP and ASR systems
no longer act on the engine
operation, but continue to act
on the brakes. Operating check
The ASR/ESP systems offer
increased safety during normal
driving, but should not incite the
driver to take risks or to drive at high
speed.
The operation of these systems is
ensured if the recommendations
of the manufacturer regarding
the wheels (tyres and rims), the
braking components, the electronic
c o m p o n e n t s a n d t h e fi t t i n g a n d r e p a i r
procedures within the PEUGEOT
network are observed.
After an impact, have the system
checked by a PEUGEOT dealer.
They engage again:
automatically above 30 mph
(50 km/h),
manually by pressing the switch
again.
Operation of the ASR and
ESP systems
T h e w a r n i n g l i g h t fl a s h e s i f
the ASR or ESP is activated.
These systems are linked and
complement the ABS.
The ASR system optimises drive to
prevent the wheels skidding, by acting
on the brakes of the drive wheels
and on the engine. It also allows the
directional stability of the vehicle to be
improved on acceleration.
If there is a variation between the
trajectory followed by the vehicle and
that required by the driver, the ESP
system automatically acts on the
engine and the brake of one or more
wheels, in order to put the vehicle back
on course, within the limits of the laws
of physics.
When a malfunction of the
systems occurs, the indicator
light comes on, accompanied
by an audible signal and a
message on the display.
Contact a PEUGEOT dealer to have
the system checked.