2010 PEUGEOT 5008 boot
[x] Cancel search: bootPage 168 of 331
139
Emergency release
For safety reasons, after this
manoeuvre it is essential to
contact a PEUGEOT dealer
urgently to replace the protective
cover.
Following an emergency unlocking,
immobilisation of the vehicle is no
longer guaranteed once the manual
emergency release has been de-
ployed and the manual control does
not allow the re-application of your
parking brake.
Take no action, either on control A , or
stopping starting the engine while the
release device is engaged.
Take care not to allow moisture or
dust in the proximity of the protective
cover.
Immobilise the vehicle (or keep
it stationary, if the brake pedal is
pressed), with the engine running,
b y e n g a g i n g fi r s t g e a r ( m a n u a l g e a r -
box), position P (automatic gearbox)
or M or R (6-speed electronic gear
control gearbox).
Switch off the engine but leave the
ignition on. If it is impossible to im-
mobilise the vehicle, do not action
the control and urgently contact a
PEUGEOT dealer.
Fetch the two vehicle blocks and
the release device, located under
the boot carpet (see "Changing a
wheel" in the "Practical information"
section).
Immobilise the vehicle by placing
blocks at the front and at the rear of
one of the rear wheels.
Slide the front left-hand seat back
as far as possible.
L i f t u p t h e fl o o r p l u g B in the carpet
under the seat.
Pierce the protective cover C on the
tube D with the release device.
Place the release device in the tube D .
Turn the release device clockwise.
For safety reasons , it is essential
to continue turning the device as
far as it will go or until you hear a
knocking noise. The parking brake
is released.
Remove the release device and store
it with the blocks in the toolbox.
- The operation of the parking brake reinitialises when the igni-
tion is switched off then on again.
If the reinitialisation of the parking
brake proves impossible, contact a
PEUGEOT dealer.
- The subsequent time required for application may be longer than dur-
ing normal operation.
Front left seat moved back fully.
In the event of the electric parking brake
malfunctioning or the battery running
fl a t , a n e m e r g e n c y m a n u a l d e v i c e c a n
release the parking brake.
Page 173 of 331
139
Emergency release
For safety reasons, after this
manoeuvre it is essential to
contact a PEUGEOT dealer
urgently to replace the protective
cover.
Following an emergency unlocking,
immobilisation of the vehicle is no
longer guaranteed once the manual
emergency release has been de-
ployed and the manual control does
not allow the re-application of your
parking brake.
Take no action, either on control A , or
stopping starting the engine while the
release device is engaged.
Take care not to allow moisture or
dust in the proximity of the protective
cover.
Immobilise the vehicle (or keep
it stationary, if the brake pedal is
pressed), with the engine running,
b y e n g a g i n g fi r s t g e a r ( m a n u a l g e a r -
box), position P (automatic gearbox)
or M or R (6-speed electronic gear
control gearbox).
Switch off the engine but leave the
ignition on. If it is impossible to im-
mobilise the vehicle, do not action
the control and urgently contact a
PEUGEOT dealer.
Fetch the two vehicle blocks and
the release device, located under
the boot carpet (see "Changing a
wheel" in the "Practical information"
section).
Immobilise the vehicle by placing
blocks at the front and at the rear of
one of the rear wheels.
Slide the front left-hand seat back
as far as possible.
L i f t u p t h e fl o o r p l u g B in the carpet
under the seat.
Pierce the protective cover C on the
tube D with the release device.
Place the release device in the tube D .
Turn the release device clockwise.
For safety reasons , it is essential
to continue turning the device as
far as it will go or until you hear a
knocking noise. The parking brake
is released.
Remove the release device and store
it with the blocks in the toolbox.
- The operation of the parking brake reinitialises when the igni-
tion is switched off then on again.
If the reinitialisation of the parking
brake proves impossible, contact a
PEUGEOT dealer.
- The subsequent time required for application may be longer than dur-
ing normal operation.
Front left seat moved back fully.
In the event of the electric parking brake
malfunctioning or the battery running
fl a t , a n e m e r g e n c y m a n u a l d e v i c e c a n
release the parking brake.
Page 203 of 331
PRACTICAL INFORMATION
171
TEMPORARY PUNCTURE REPAIR KIT
Complete system consisting of a com-
pressor and an incorporated sealant
cartridge which permits temporary
repair of the tyre so that you can drive
to the nearest garage.
A l l o f t h e s e t o o l s a r e s p e c i fi c t o y o u r
vehicle. Do not use them for other
purposes.
1. 12 V compressor.
Contains a sealant for temporary repair of the tyre and permits ad-
justment of the tyre pressure.
2. Two chocks to chock the vehicle.
3. Socket for security bolts (located
in the glove compartment).
Permits adaptation to the special security bolts.
List of tools Other accessories
4. Removable towing eye.
Refer to "Electric parking brake" in the "Driving" section.
Refer to the paragraph "Towing
the vehicle".
5. Electric parking brake emergency
release control.
Access to the kit
The kit is located in the boot under the
concertina board.
The tools
4 and 5 are located in the boot
interior trim, on the left-hand side.
Page 207 of 331
PRACTICAL INFORMATION
175
CHANGING A WHEEL
The tools 2 to 4 a r e i n s t a l l e d i n a b o x ,
in the middle of the spare wheel, placed
underneath the vehicle.
The tools 1 and 6 to 9 are installed
under the concertina boards, in the boot
inner trim.
T o g a i n a c c e s s t o t h e m :
open the boot,
raise the concertina boards,
Access to the tools
Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
vided with the vehicle.
A l l o f t h e s e t o o l s a r e s p e c i fi c t o y o u r
vehicle. Do not use them for other
purposes.
List of tools
1. Wheelbrace.
For removing the wheel trim and t h e w h e e l fi x i n g b o l t s .
2. Jack with integral handle.
For raising the vehicle.
3. "Bolt cover" tool (according to
equipment).
For removing the bolt protectors (covers) on alloy wheels.
4. Centring guide.
F o r r e fi t t i n g a n a l l o y w h e e l t o t h e hub.
5. Socket for the security bolts
( l o c a t e d i n t h e g l o v e b o x ) .
For adaptating the wheelbrace to the special security bolts.
6. Two chocks to immobilise the
vehicle.
7. W h e e l b r a c e e x t e n s i o n .
For unscrewing/tightening the spare wheel carrier drive.
Page 212 of 331
PRACTICAL INFORMATION
180
After changing a wheel
To store the punctured wheel in the boot
c o r r e c t l y , fi r s t r e m o v e t h e c e n t r a l c o v e r .
When using the "space-saver" type
s p a r e w h e e l , d o n o t e x c e e d 5 0 m p h
(80 km/h).
Have the tightening of the bolts and the
pressure of the spare wheel checked
by a PEUGEOT dealer without delay.
Have the punctured wheel repaired
and replace it on the vehicle as soon as
possible.
Fitting a wheel
List of operations
Put the wheel in place on the hub
using the centring guide 4 .
Screw in the bolts by hand to the
stop.
Pre-tighten the security bolt us-
ing the wheelbrace 1 fi t t e d w i t h t h e
security socket 5 .
Pre-tighten the other bolts using the
wheelbrace 1 only.
Lower the vehicle fully.
Fold the jack 2 and detach it.
Tighten the security bolt using the
wheelbrace 1 fi t t e d w i t h t h e s e c u r i t y
socket 5 .
Tighten the other bolts using the
wheelbrace 1 only.
R e fi t t h e c h r o m e d b o l t c o v e r s o n
each of the bolts (according to
equipment).
S t o r e t h e t o o l s i n t h e b o x .
Fitting the "space-saver"
spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a l -
loy wheels, when tightening the bolts
o n fi t t i n g i t i s n o r m a l t o n o t i c e t h a t t h e
washers do not come into contact
with the "space-saver" spare wheel.
The wheel is secured by the conical
contact of each bolt.
Page 217 of 331
PRACTICAL INFORMATION
185
Changing the third brake lamp bulb Changing the number plate lamp
bulbs (W5-5W)
Insert a thin screwdriver into one of
the outer holes of the lens.
Push it outwards to unclip.
Remove the lens.
Pull the bulb and change it.
Changing foglamp bulbs
Reach under the bumper.
Turn the bulb a quarter of a turn and
change it.
Open the boot and remove the upper
seal.
Unscrew the two nuts.
Press the threaded pins while sup-
porting the lamp from the outside.
Disconnect the connector and remove
the screenwash pipe.
Press the pairs of clips A then B
then C to detach and gain access to
the bulb holder.
Changing sidelamps (diodes)
For the replacement of this type of diode
lamp, contact a PEUGEOT dealer.
Page 219 of 331
PRACTICAL INFORMATION
187
Dashboard fuses
T h e f u s e b o x i s p l a c e d i n t h e l o w e r s e c t i o n
of the dashboard (left-hand side). Fuse tables
F us e N° Ratin g
(A) Functions
F1 15 Rear wiper.
F2 - Not used.
F3 5 Airbag control unit.
F4 10 Electrochromatic rear view mirror, air conditioning,
switching and protection unit, rear multimedia.
F5 30 Front one-touch electric windows.
F6 30 Rear one-touch electric windows.
F7 5 Front and rear courtesy lamps, map reading lamps,
r e a r r e a d i n g l a m p s , s u n v i s o r l i g h t i n g , g l o v e b o x
lighting, centre armrest lighting, boot 12 V relay
control.
Page 221 of 331
PRACTICAL INFORMATION
189
Fuse N° Rating
(A) Functions
F29 30 Boot 12 V socket.
F30 5 Heated door mirrors.
F31 15 Refrigerator socket.
F32 5 E l e c t r o n i c g e a r c o n t r o l m a n u a l g e a r b o x g e a r l e v e r .
F33 10 Head-up display, Bluetooth system, air conditioning.
F34 5 Seat belt warning lamps display.
F35 10 P a r k i n g s e n s o r s , H i - F i a m p l i fi e r a u t h o r i s a t i o n .
F36 10 T r a i l e r f u s e b o x c o n t r o l u n i t , d r i v e r ' s d o o r c o n t r o l p a d .
F37 20 H i - F i a m p l i fi e r .
F38 30 Driver's electric seat.
F39 20 Panoramic sunroof blind.
F40 - Not used.