2010 Peugeot 407 Stop
[x] Cancel search: StopPage 68 of 249
4ACCESS
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REINITIALISATION
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking but-
ton immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
reinitialise the remote control.
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator lamp
It is accompanied by a message on
the multi-function screen.
Your vehicle will not start.
Consult a PEUGEOT dealer.
This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correct-
ly, the following indicator lamp comes on:
Remote control
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
Do not repeatedly press the buttons of
your remote control out of range and
out of sight of your vehicle. You run the
risk of stopping it from working and the
remote control would have to be reini-
tialised.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reinitialisation.
Locking the vehicle
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time. Lost keys
Visit a PEUGEOT dealer with
the vehicle's V5 registration
d o c u m e n t a n d y o u r p e r s o n a l i d e n t i fi -
cation documents.
The PEUGEOT dealer will be able to re-
trieve the key code and the transponder
code required to order a replacement key.
Page 69 of 249
4ACCESS
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REINITIALISATION
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking but-
ton immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
reinitialise the remote control.
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator lamp
It is accompanied by a message on
the multi-function screen.
Your vehicle will not start.
Consult a PEUGEOT dealer.
This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correct-
ly, the following indicator lamp comes on:
Remote control
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
Do not repeatedly press the buttons of
your remote control out of range and
out of sight of your vehicle. You run the
risk of stopping it from working and the
remote control would have to be reini-
tialised.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reinitialisation.
Locking the vehicle
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time. Lost keys
Visit a PEUGEOT dealer with
the vehicle's V5 registration
d o c u m e n t a n d y o u r p e r s o n a l i d e n t i fi -
cation documents.
The PEUGEOT dealer will be able to re-
trieve the key code and the transponder
code required to order a replacement key.
Page 73 of 249
4ACCESS
66
Reactivation of the interior
volumetric monitoring
Press the unlocking button on the
remote control to deactivate the
exterior perimeter monitoring.
Press the locking button on the
remote control to activate all the
monitoring functions.
The indicator lamp on the button again
fl a s h e s o n c e p e r s e c o n d . Triggering of the alarm
This is indicated by sounding of the
s i r e n a n d fl a s h i n g o f t h e d i r e c t i o n i n d i -
cators for thirty seconds.
The monitoring functions remain ac-
tive until the alarm has been triggered
eleven times in succession.
When the vehicle is unlocked using
t h e r e m o t e c o n t r o l , r a p i d fl a s h i n g o f
the indicator lamp on the button in-
forms you that the alarm was triggered
during your absence. When the igni-
t i o n i s s w i t c h e d o n , t h i s fl a s h i n g s t o p s
immediately.
Failure of the remote control
To deactivate the monitoring functions:
Unlock the vehicle using the key in
the driver's door lock.
Open the door; the alarm is trig-
gered.
Switch on the ignition; the alarm
stops. The indicator lamp on the
button switches off. Locking the vehicle without
activating the alarm
Lock or deadlock the vehicle using
the key in the driver's door lock.
Malfunction
W h e n t h e i g n i t i o n i s s w i t c h e d o n , fi x e d
lighting of the indicator lamp on the
button indicates a malfunction of the
system.
Have it checked by a PEUGEOT dealer.
* According to country.
Automatic activation *
2 minutes after the last door or the
boot is closed, the system is activated
automatically.
To avoid triggering the alarm on
e n t e r i n g t h e v e h i c l e , fi r s t p r e s s t h e
unlocking button on the remote
control.
Page 74 of 249
4ACCESS
67
ELECTRIC WINDOWS
Automatic operation:
To open or close the window, press or
pull switch fully: the window opens or
closes completely when the switch is
released. Pressing the switch again
stops the movement of the window.
The electric window switches remain
operational for approximately one min-
ute after the key has been removed
from the ignition.
Once this time has elapsed, the electric
windows will not operate. To reactivate
them, switch the ignition on again.
Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
In the event of contact during
operation of the windows, you must re-
verse the movement of the window. To
do this, press the switch concerned.
When the driver operates the passen-
ger electric window switches, he must
ensure that no one is preventing cor-
rect closing of the windows.
The driver must ensure that the pas-
sengers use the electric windows cor-
rectly.
Be aware of children when operating
the windows. REINITIALISATION OFTHE ELECTRIC WINDOWS
Following reconnection of the battery,
the safety anti-pinch function must be re-
initialised: the safety anti-pinch function
is not active during these operations.
- lower the window completely, then raise it, it will rise in steps of a few
centimetres each time the switch is
pressed. Repeat the operation un-
til the window closes completely,
- continue to press the switch for at least one second after reaching
this position, window closed.
Safety anti-pinch
When the window rises and meets an
obstacle, it stops and immediately par-
tially lowers again.
In the event of unwanted opening
of the window on closing, press the
switch until the window opens com-
pletely, then pull the switch immediate-
ly until the window closes. Continue to
hold the switch for approximately one
second after the window has closed.
The safety anti-pinch function is not
active during this operation.
Deactivating the rear window
controls
For the safety of your children, press
switch 5 to prevent operation of the rear
windows irrespective of their position.
When the button is pressed down, the
switches are deactivated. When the but-
ton is raised, the switches are active.
Manual operation:
To open or close the window, press
or pull the switch gently. The win-
dow stops as soon as the switch is
released.
1. Driver's electric window switch.
2. Passenger's electric window
switch.
3. Rear right electric window
switch.
4. Rear left electric window
switch.
5. Deactivating the rear electric
window switches (child safety).
Page 78 of 249
4ACCESS
70
Notes:
After reconnecting the battery, you
must reinitialise the safety anti-pinch:
- place the control in the maximum partial opening position (3rd notch
to the right),
- wait until the roof is in the maxi- mum partially open position,
- press the control for at least one second.
In the event of unwanted opening of
the roof on closing (for example, in the
presence of ice), and immediately af-
ter the roof stops:
- move the control to the "O" position and press the control immediately,
- continue to press the control until the roof is fully closed. SUNROOF (SALOON) Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
In the event of contact during
operation of the roof, you must reverse
the movement of the roof. To do this,
press the switch concerned.
When the driver operates the roof
switch, they must ensure that no one
is preventing correct closing of the
roof.
The driver must ensure that passen-
gers use the sunroof correctly.
Be aware of children when operating
the roof.
- To partially open the roof: Turn the switch to the right (three possible
settings).
- To open the roof completely: Turn the switch to the left (six possible
settings).
- To close it completely: Turn the switch back to position "O".
- Safety anti-pinch: When the sun- roof is closing and meets an ob-
stacle, it stops then partially opens
again.
The sunroof blind is manual.
Page 79 of 249
4ACCESS
71
Safety anti-pinch
If the blind encounters an obstacle
during closing, it stops and partially
opens again.
You must reinitialise the safety anti-
p i n c h w i t h i n a m a x i m u m o f fi v e s e c -
onds after the blind has stopped:
- press part A of the control until the
blind is completely closed (closing
in stages of a few centimetres). PANORAMIC SUNROOF (407SW) In the event of contact du-
ring operation of the blind, you
must reverse its movement.
To do this, press the control
concerned.
When the driver operates the blind-
control, they must ensure that no one
is preventing the blind from closing
correctly.
The driver must ensure that the pas-
sengers use the blind correctly.
Pay attention to children during opera-
tion of the blind.
Notes:
Following reconnection of the battery,
in the event of a blind malfunction
while it is moving or immediately after
it has stopped, you must reinitialise
the safety anti-pinch:
- place the control in the fully open position (position "0"),
- wait until the blind is in the fully open position,
- press section A of the control for at
least three seconds.
In the event of unwanted opening of
the blind on closing, and immediately
after the blind has stopped:
- move the control to the fully closed position (9th setting to the left) then
press part A of the control straight
away,
- continue to press the control until the blind is fully closed.
The safety anti-pinch function is not
active during these operations.
Y o u r v e h i c l e i s fi t t e d w i t h a t i n t e d g l a s s
panoramic sunroof which increases
the light and visibility in the passen-
ger compartment. Its electric blind im-
proves temperature conditions.
The blind is controlled electrically by
a dial with nine opening positions.
To close: turn the dial to the left (nine
possible settings).
To open: return the dial to the initial
position "0" .
Page 84 of 249
5
75
Automatic illumination of
headlamps
T h e d i p p e d b e a m h e a d l a m p s s w i t c h
o n a u t o m a t i c a l l y i f t h e l i g h t i s p o o r a n d
when the windscreen wipers operate
continuously. They switch off when
the light is bright enough or the wind-
screen wipers stop.
Warning: in foggy weather or in snow,
t h e s u n s h i n e s e n s o r c a n d e t e c t s u f fi -
c i e n t l i g h t . T h e l i g h t i n g w i l l n o t c o m e
o n a u t o m a t i c a l l y . I f n e c e s s a r y , y o u
m u s t s w i t c h t h e d i p p e d b e a m h e a d -
l a m p s o n m a n u a l l y . Activation Manual "Guide-me-home" lighting
When you leave your vehicle, the side-
l a m p s a n d d i p p e d b e a m h e a d l a m p s
can be left on for a few seconds.
When the function is activated, the
i n d i c a t o r l a m p c o m e s o n o n t h e
5 - d i a l i n s t r u m e n t p a n e l s c r e e n .
To deactivate or activate the
function, use the "Persona-
l i s a t i o n - c o n fi g u r a t i o n "
m e n u o n y o u r m u l t i f u n c t i o n
screen.
F o r s a f e t y r e a s o n s , a c t i v a t i o n /
d e a c t i v a t i o n o f t h e " A u t o m a t i c
i l l u m i n a t i o n o f h e a d l a m p s s "
f u n c t i o n v i a t h e m e n u m u s t b e
carried out when stationary. To deactivate or activate the
" A u t o m a t i c g u i d e - m e - h o m e
lighting" function, use the
"Personalisation - confi-
guration" m e n u o n y o u r
m u l t i f u n c t i o n s c r e e n .
The duration of the lighting
can be set via the "Person-
a l i s a t i o n - c o n fi g u r a t i o n "
m e n u o f y o u r m u l t i f u n c t i o n
screen.
Automatic "Guide-me-home"
lighting
When you leave your vehicle
with
the automatic illumination of head-
lamps a c t i v a t e d , t h e s i d e l a m p s a n d
d i p p e d b e a m h e a d l a m p s r e m a i n o n
for the duration selected after the igni-
tion is switched off.
Deactivation
When the function is deactivated,
t h e i n d i c a t o r l a m p c o m e s o n o n t h e
5 - d i a l i n s t r u m e n t p a n e l s c r e e n .
D o n o t c o v e r t h e s u n s h i n e /
brightness sensor, located in
the centre of the windscreen.
It is used to regulate the air
c o n d i t i o n i n g a n d f o r t h e a u t o m a t i c i l -
l u m i n a t i o n o f h e a d l a m p s .
If the sunshine/brightness sensor
does not function correctly, the
s i d e l a m p s a n d d i p p e d b e a m h e a d l a m -
p s c o m e o n .
Consult a PEUGEOT dealer.
Activation:
switch off the engine,
" fl a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Page 85 of 249
5
75
Automatic illumination of
headlamps
T h e d i p p e d b e a m h e a d l a m p s s w i t c h
o n a u t o m a t i c a l l y i f t h e l i g h t i s p o o r a n d
when the windscreen wipers operate
continuously. They switch off when
the light is bright enough or the wind-
screen wipers stop.
Warning: in foggy weather or in snow,
t h e s u n s h i n e s e n s o r c a n d e t e c t s u f fi -
c i e n t l i g h t . T h e l i g h t i n g w i l l n o t c o m e
o n a u t o m a t i c a l l y . I f n e c e s s a r y , y o u
m u s t s w i t c h t h e d i p p e d b e a m h e a d -
l a m p s o n m a n u a l l y . Activation Manual "Guide-me-home" lighting
When you leave your vehicle, the side-
l a m p s a n d d i p p e d b e a m h e a d l a m p s
can be left on for a few seconds.
When the function is activated, the
i n d i c a t o r l a m p c o m e s o n o n t h e
5 - d i a l i n s t r u m e n t p a n e l s c r e e n .
To deactivate or activate the
function, use the "Persona-
l i s a t i o n - c o n fi g u r a t i o n "
m e n u o n y o u r m u l t i f u n c t i o n
screen.
F o r s a f e t y r e a s o n s , a c t i v a t i o n /
d e a c t i v a t i o n o f t h e " A u t o m a t i c
i l l u m i n a t i o n o f h e a d l a m p s s "
f u n c t i o n v i a t h e m e n u m u s t b e
carried out when stationary. To deactivate or activate the
" A u t o m a t i c g u i d e - m e - h o m e
lighting" function, use the
"Personalisation - confi-
guration" m e n u o n y o u r
m u l t i f u n c t i o n s c r e e n .
The duration of the lighting
can be set via the "Person-
a l i s a t i o n - c o n fi g u r a t i o n "
m e n u o f y o u r m u l t i f u n c t i o n
screen.
Automatic "Guide-me-home"
lighting
When you leave your vehicle
with
the automatic illumination of head-
lamps a c t i v a t e d , t h e s i d e l a m p s a n d
d i p p e d b e a m h e a d l a m p s r e m a i n o n
for the duration selected after the igni-
tion is switched off.
Deactivation
When the function is deactivated,
t h e i n d i c a t o r l a m p c o m e s o n o n t h e
5 - d i a l i n s t r u m e n t p a n e l s c r e e n .
D o n o t c o v e r t h e s u n s h i n e /
brightness sensor, located in
the centre of the windscreen.
It is used to regulate the air
c o n d i t i o n i n g a n d f o r t h e a u t o m a t i c i l -
l u m i n a t i o n o f h e a d l a m p s .
If the sunshine/brightness sensor
does not function correctly, the
s i d e l a m p s a n d d i p p e d b e a m h e a d l a m -
p s c o m e o n .
Consult a PEUGEOT dealer.
Activation:
switch off the engine,
" fl a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it.