Page 175 of 315
151
Stopping the vehicle Operating fault
With the ignition on, if this
warning lamp comes on and
AUTO fl a s h e s , a c c o m p a n i e d
by an audible signal and a
message on the multifunction
screen, this indicates a malfunction of
the gearbox.
Have it checked by a PEUGEOT dealer.
It is essential to press the
brake pedal when starting the
engine.
When parking, is it essential to apply
the parking brake to immobilise the
vehicle, whatever the circumstances.
When immobilising the vehi-
cle, with the engine running, it
is essential to place the gear
lever in neutral N .
Before carrying out any work in the
engine compartment, check that the
gear lever is in neutral N and that
the parking brake is applied.
Sport function
Following selection of the sequential
mode or automatic mode, press but-
ton S to activate the Sport function
which offers you a more dynamic
style of driving.
S appears next to the gear en-
gaged on the instrument panel
screen.
Press button S again to deactivate
the function.
S is then cleared from the instrument
panel screen.
The gearbox returns to normal
mode automatically each time
the ignition is switched off. Before switching off the engine, you can
choose to:
- move to position
N to engage neutral,
- leave the gear engaged; in this case, it will not be possible to move
the vehicle.
In both cases, it is essential that you ap-
ply the parking brake to immobilise the
vehicle.
Page 232 of 315
207
TU
PQRS
0
*
1 1
SETUP
2 2
0 2
B e f o r e u s i n g t h e s y s t e m f o r t h e fi r s t t i m e , y o u a r e a d v i s e d t o listen to, say and repeat the instructions for use.
Press the SETUP button and select the "Language & Speech" function. Turn the ring and select "Voice control". Activate voice recognition. Select "Tutorial".
V O I C E C O M M A N D S - V O I C E
R E C O . I N I T I A T I O N
The phrases to be spoken according to the context are indicated in the tables below. Speak and Peugeot Connect Media acts.
A short press activates voice recognition. A long press on this button activates voice recognition.
CONTEXT SAY ACTION
GENERAL Help address book Help voice control Help media Help navigation Help telephone Help radio Cancel
Correction
Access to the address book help Access to the voice reco help Access to the media management help Access to the guidance, navigation help Access to the telephone help Access to the radio help To cancel a voice commandwhich is in progress Request to correct the last voicerecognition carried out Clear
RADIO Select station S t a t i o n < t t s : s t a t i o n N a m e >
Read out station list Enter frequency
Select wave band
AM FM TA on TA off
Select a radio station Select a radio station using its RDS d e s c r i p t i o n < t t s : s t a t i o n N a m e > f r o mthe RADIO list Listen to the list of stations available Listen to the frequency of the currentradio station Choose the frequency waveband ( A M o r F M ) Change the frequency waveband to AM Change the frequency waveband to FM A c t i v a t e t h e T r a f fi c I n f o ( T A ) D e a c t i v a t e t h e T r a f fi c I n f o
N A V I G A T I O N Destination input
Voice advice off
Voice advice on Save address
Start guidance
Abort guidance Navigate entry
POI Search
Command to enter a new destinationaddress Deactivate the spoken guidanceinstructions Activate the spoken guidance instructions Save an address in the address book Start guidance (once the address has b e e n e n t e r e d ) Stop the guidance S t a r t g u i d a n c e t o a fi l e i n the address book Start guidance to a point of interest
V O I C E C O M M A N D S A N D S T E E R I N G M O U N T E D C O N T R O L S
Page 241 of 315
216
NAV
5
6
7
1
2
3
4
8
0 4
A D D I N G A S T O P O V E R
Enter a new address, for example.
Once the new address has been entered, select "Start route guidance" a n d p r e s s O K t o c o n fi r m .
Position the stopover on the list and p r e s s O K t o c o n fi r m .
Press the NAV button.
Press the NAV button again or select the "Navigation" Menu function and p r e s s O K t o c o n fi r m .
Select the "Add stopover" function ( 5 s t o p o v e r s m a x i m u m ) a n d p r e s s O K t o c o n fi r m .
Select the "Stopovers" function and p r e s s O K t o c o n fi r m .
" N A V I G A T I O N " M E N U
ADDRESS INPUT
A D D S T O P O V E R
S T O P O V E R S
START ROUTE GUIDANCE
To change the stopovers, repeat operations 1 to 3 and s and select "Rearrange route" (select a stopover, delete it or move iove it on the list u s i n g t h e r i n g t o c h a n g e t h e o r d e r , c o n fi r m i t s n e w p o s i t i o n a n d fi n i s h u s i n g t h e r i n g t o c h a n g e t h e o r d e r , c o n fi r m i t s n e w p o s i t i o n a n d fi n i s h w i t h " R e c a l c u l a t e " ) .
Stopovers can be added to or deleted from the route once the destination has been selected.
Repeat operations 1 to 7 as many times as necessar y then select " R e c a l c u l a t e " a n d p r e s s O K t o c o n fi r m .
N A V I G A T I O N - G U I D A N C E