2010 Peugeot 3008 Dag faulty
[x] Cancel search: faultyPage 138 of 315
119
TYRE UNDER-INFLATION DETECTION
System which automatically checks the
pressure of the tyres while driving. All repairs and changing of
t y r e s o n a w h e e l fi t t e d w i t h t h i s
system must be carried out by
a PEUGEOT dealer.
If, when changing a tyre, you install
a wheel which is not detected by
y o u r v e h i c l e ( e x a m p l e : fi t t i n g o f s n o w
tyres), you must have the system re-
initialised by a PEUGEOT dealer.
This system does not eliminate
the need to have the tyre pres-
sure checked regularly (refer
t o t h e " I d e n t i fi c a t i o n m a r k i n g s " p a r a -
graph) to ensure that the optimum
dynamic performance of the vehicle
is maintained and prevent premature
wear of the tyres, particularly in ardu-
ous driving conditions (heavy load,
high speed).
The tyre pressures must be checked
cold, at least once a month. Re-
member to check the pressure of the
spare wheel.
T h e t y r e u n d e r - i n fl a t i o n d e t e c t i o n
system may experience temporary
interference due to radioelectric
emissions on a frequency close to
that used by the system.
S e n s o r s fi t t e d i n e a c h v a l v e t r i g g e r a
warning in the event of malfunction
(speed above 12 mph (20 km/h)).
T h e s p a r e w h e e l i s n o t fi t t e d w i t h a s e n s o r .
This warning lamp is displayed on the
instrument panel and/or a message ap-
pears on the multifunction screen, ac-
companied by an audible signal, to locate
the wheel concerned.
Check the tyre pressures as soon as possible.
This check must be carried out when the tyres are
cold.
Flat tyre The
STOP warning lamp
comes on, accompanied by
an audible signal and a mes-
sage on the multifunction
screen locating the wheel
concerned.
Stop immediately, avoiding any sud-
den movement of the steering wheel
and the brakes.
Change the damaged wheel (punc-
t u r e d o r v e r y d e fl a t e d t y r e ) , a n d
have the tyre pressure checked as
soon as possible.
Puncture
T h e t y r e u n d e r - i n fl a t i o n d e t e c -
tion system is an aid to driv-
ing which does not replace the
need for the driver to be vigilant or to
drive responsibly. Sensor(s) not detected or faulty
A message appears on the multifunc-
tion screen, accompanied by an audible
signal, to locate the wheel or wheels
which are not detected or to indicate a
fault in the system.
Contact a PEUGEOT dealer to replace
the faulty sensor(s).
This message is also dis-
played when one of the wheels
is away from the vehicle (be-
ing repaired) or when one or more
w h e e l s w i t h o u t a s e n s o r a r e fi t t e d .
Page 155 of 315
134
Particular situations Emergency braking
In the event of a failure of the main ser-
vice brake or in an exceptional situation
(e.g. driver taken ill, under instruction,
etc) a continuous pull on control A will
stop the vehicle.
The electronic stability programme
(ESP) provides stability during emer-
gency braking.
If the emergency braking malfunctions,
one of the following messages will be
displayed:
- "Parking brake faulty".
- "Parking brake control faulty".
In certain situations (e.g.
starting the engine), the parking brake
can automatically alter its force. This
is normal operation.
To advance your vehicle a few cen-
timetres without starting the engine,
but with the ignition on, press on the
brake pedal and release the parking
brake by pulling then releasing con-
trol A . The full release of the parking
b r a k e i s c o n fi r m e d b y t h e e x t i n c t i o n
of warning lamp on control A and of
the warning lamp on the instrument
panel and the displaying of the mes-
sage "Handbrake off".
If the parking brake malfunctions
while applied or if the battery runs
fl a t , a n e m e r g e n c y r e l e a s e i s a l w a y s
possible.
If a failure of the ESP sys-
tem is signalled by the light-
ing of this warning lamp, then
braking stability is not guaranteed.
The emergency braking must
only be used in exceptional
circumstances.
In this event, stability must be assured
by the driver by repeating alternate "pull
release" actions on control
A .
Page 160 of 315
134
Particular situations Emergency braking
In the event of a failure of the main ser-
vice brake or in an exceptional situation
(e.g. driver taken ill, under instruction,
etc) a continuous pull on control A will
stop the vehicle.
The electronic stability programme
(ESP) provides stability during emer-
gency braking.
If the emergency braking malfunctions,
one of the following messages will be
displayed:
- "Parking brake faulty".
- "Parking brake control faulty".
In certain situations (e.g.
starting the engine), the parking brake
can automatically alter its force. This
is normal operation.
To advance your vehicle a few cen-
timetres without starting the engine,
but with the ignition on, press on the
brake pedal and release the parking
brake by pulling then releasing con-
trol A . The full release of the parking
b r a k e i s c o n fi r m e d b y t h e e x t i n c t i o n
of warning lamp on control A and of
the warning lamp on the instrument
panel and the displaying of the mes-
sage "Handbrake off".
If the parking brake malfunctions
while applied or if the battery runs
fl a t , a n e m e r g e n c y r e l e a s e i s a l w a y s
possible.
If a failure of the ESP sys-
tem is signalled by the light-
ing of this warning lamp, then
braking stability is not guaranteed.
The emergency braking must
only be used in exceptional
circumstances.
In this event, stability must be assured
by the driver by repeating alternate "pull
release" actions on control
A .
Page 193 of 315
PRACTICAL INFORMATION
169
CHANGING A WHEEL
The tools are installed in the boot under
t h e fl o o r .
T o g a i n a c c e s s t o t h e m :
o p e n t h e b o o t ,
p l a c e t h e a d j u s t a b l e b o o t fl o o r a t a n
a n g l e ( r e f e r t o t h e " F i t t i n g s " s e c t i o n ) ,
r a i s e t h e fl o o r ,
secure it by hooking its cord on the
h o o k o n t h e r e a r p a r c e l s h e l f s u p -
p o r t ,
r e m o v e t h e p o l y s t y r e n e s t o r a g e b o x ,
unclip by pulling upwards then
r e m o v e t h e b o x c o n t a i n i n g t h e
t o o l s .
Access to the tools
Procedure for changing a faulty wheel
f o r t h e s p a r e w h e e l u s i n g t h e t o o l s p r o -
v i d e d w i t h t h e v e h i c l e .
T o m a k e t h e o p e r a t i o n e a s i e r , r e -
m o v e t h e a d j u s t a b l e b o o t fl o o r ,
u n s c r e w t h e y e l l o w c e n t r a l b o l t ,
With the JBL bass unit
remove the bass unit disconnecting
t h e e l e c t r i c a l h a r n e s s ,
r e m o v e t h e p o l y s t y r e n e s t o r a g e b o x .
Page 194 of 315
PRACTICAL INFORMATION
169
CHANGING A WHEEL
The tools are installed in the boot under
t h e fl o o r .
T o g a i n a c c e s s t o t h e m :
o p e n t h e b o o t ,
p l a c e t h e a d j u s t a b l e b o o t fl o o r a t a n
a n g l e ( r e f e r t o t h e " F i t t i n g s " s e c t i o n ) ,
r a i s e t h e fl o o r ,
secure it by hooking its cord on the
h o o k o n t h e r e a r p a r c e l s h e l f s u p -
p o r t ,
r e m o v e t h e p o l y s t y r e n e s t o r a g e b o x ,
unclip by pulling upwards then
r e m o v e t h e b o x c o n t a i n i n g t h e
t o o l s .
Access to the tools
Procedure for changing a faulty wheel
f o r t h e s p a r e w h e e l u s i n g t h e t o o l s p r o -
v i d e d w i t h t h e v e h i c l e .
T o m a k e t h e o p e r a t i o n e a s i e r , r e -
m o v e t h e a d j u s t a b l e b o o t fl o o r ,
u n s c r e w t h e y e l l o w c e n t r a l b o l t ,
With the JBL bass unit
remove the bass unit disconnecting
t h e e l e c t r i c a l h a r n e s s ,
r e m o v e t h e p o l y s t y r e n e s t o r a g e b o x .
Page 199 of 315
PRACTICAL INFORMATION
174
Risk of electrocution
X e n o n b u l b s ( D 1 S - 3 5 W ) m u s t
be replaced by a PEUGEOT
d e a l e r .
CHANGING A BULB
Procedure for replacing a faulty bulb
with a new bulb without the use of
t o o l s .
Model with halogen headlamps
1. Direction indicators
(HP24-24W).
2. Dipped
beam
headlamps
(H7-55W).
3. Main beam headlamps (H7-55W).
4. Daytime
running lamps
(HP24-24W).
5. Foglamps
(PS24-24W).
6. Sidelamps
(W5-5W).
1. Direction indicators
(HP24-24W).
2. Dipped/main beam headlamps
(D1S-35W).
3. Daytime
running lamps/
sidelamps
(P21/5W).
4. Foglamps
(PS24-24W).
Model with xenon and dir
ectional
headlamps T h e h e a d l a m p s a r e fi t t e d w i t h
polycarbonate glass with a
p r o t e c t i v e c o a t i n g :
do not clean them using a dry
or abrasive cloth, nor with a
detergent or solvent product,
u s e a s p o n g e a n d s o a p y w a t e r ,
when using a high pressure
w a s h e r o n p e r s i s t e n t m a r k s , d o
not direct at the lamps or their
o u t l i n e s f o r t o o l o n g , s o a s n o t t o
damage their protective coating
a n d s e a l s .
Front lamps
D o n o t t o u c h t h e b u l b d i r e c t l y w i t h
y o u r fi n g e r s , u s e l i n t - f r e e c l o t h s .
Changing a halogen bulb should only
be done after the headlamp has been
switched off for a few minutes (risk of
s e r i o u s b u r n s ) .
I t i s i m p e r a t i v e t o u s e o n l y a n t i - u l t r a -
violet (UV) type bulbs in order not to
d a m a g e t h e h e a d l a m p .
Page 204 of 315
PRACTICAL INFORMATION
179
CHANGING A FUSE
Procedure for replacing a faulty fuse
with a new fuse to rectify a failure of the
c o r r e s p o n d i n g f u n c t i o n .
Access to the tools
T h e e x t r a c t i o n p l i e r s a n d t h e s p a r e f u s -
e s a r e i n s t a l l e d o n t h e b a c k o f t h e d a s h -
b o a r d f u s e b o x c o v e r .
T o g a i n a c c e s s t o t h e m :
r e m o v e t h e c o v e r c o m p l e t e l y ,
r e m o v e t h e p l i e r s . Changing a fuse
B e f o r e c h a n g i n g a f u s e , t h e c a u s e o f
t h e f a i l u r e m u s t b e i d e n t i fi e d a n d r e c t i -
fi e d .
I d e n t i f y t h e f a u l t y f u s e b y c h e c k i n g
t h e c o n d i t i o n o f i t s fi l a m e n t .
Correct Incorrect
U s e t h e s p e c i a l p l i e r s t o e x t r a c t t h e
f u s e f r o m i t s h o u s i n g .
Always replace the faulty fuse with a
f u s e o f t h e s a m e r a t i n g .
Check the correspondence between
t h e n u m b e r e t c h e d o n t h e b o x , t h e
rating etched on the fuse and the
t a b l e s b e l o w . Installing electrical
accessories
Your vehicle's electrical system
is designed to operate with standard
o r o p t i o n a l e q u i p m e n t .
Before installing other electrical
equipment or accessories on your
v e h i c l e , c o n t a c t a P E U G E O T d e a l e r .
PEUGEOT will not accept
responsibility for the cost
incurred in repairing your
v e h i c l e o r f o r r e c t i f y i n g m a l -
f u n c t i o n s r e s u l t i n g f r o m t h e i n s t a l l a -
tion of accessories not supplied and
not recommended by PEUGEOT
and not installed in accordance with
i t s i n s t r u c t i o n s , i n p a r t i c u l a r w h e n
the combined consumption of all of
the additional equipment connected
e x c e e d s 1 0 m i l l i a m p e r e s .