2010 Peugeot 207 CC headlamp
[x] Cancel search: headlampPage 84 of 207
!
i
VISIBILITY
78
Model with front and rear foglamps front and rear foglamps
C. foglamps selection ring.
These operate with the dipped and main
beam headlamps.
To switch on the foglamps, turn ring C
forwards.
To switch off the rear foglamps, turn
ring C rearwards twice in succession.
When the lighting is switched off auto-
m a t i c a l l y ( o n A U T O m o d e l ) o r w h e n t h e
dipped beam headlamps are switched
off manually, the foglamps and the side-
lamps will remain on.
Turn the ring rearwards to switch
off the foglamps, the sidelamps will
then switch off.
Do not forget to switch off the front
foglamps and the rear foglamps
when they are no longer neces-
sary. In normal light levels, the
power of their beams may dazzle
other drivers. Lighting on reminder
The triggering of an audible signal
when a door is opened warns the
driver that they have forgotten to
switch off the vehicle's lighting, with
the ignition off.
In this case, switching off the light-
ing will stop the audible signal.
When the ignition is switched off,
if the dipped beam headlamps re-
main on, they will be switched off
automatically after thirty minutes to
prevent discharging of the battery. This indicator lamp comes on
on the instrument panel.
* According to country.
Daytime running lamps *
O n v e h i c l e s fi t t e d w i t h d a y t i m e r u n n i n g
lamps, the dipped beam headlamps
come on when the vehicle is started.
The instruments and controls (multi-
function screen, air conditioning control
p a n e l , . . . ) a r e n o t l i t , u n l e s s t h e a u t o -
matic lighting mode is activated or the
lighting is switched on manually.
Page 85 of 207
!
VISIBILITY
Do not cover the sunshine sensor,
located in the centre of the wind-
screen behind the rear view mirror;
the associated functions would no
longer be controlled.
Coupling with the "Guide-me-home"
lighting
Association with the automatic illumination of
headlamps provides the "guide-me-home"
lighting with the following additional options:
-
selection of the lighting duration to 15, 30
or 60 seconds in the vehicle parameters
o n t h e m u l t i f u n c t i o n s c r e e n c o n fi g u r a -
tion menu,
- automatic activation of "guide-me- home" lighting when automatic illumi-
nation of headlamps is in operation.
Automatic illumination of headlamps
The sidelamps and dipped beam head-
lamps are switched on automatically, with-
out any action on the part of the driver,
when a low level of external light is detect-
e d ( s e n s o r b e h i n d t h e r e a r v i e w m i r r o r ) .
A s s o o n a s t h e b r i g h t n e s s r e t u r n s t o a s u f fi c i e n t
level, the lighting is switched off automatically.
"Guide-me-home" lighting
The dipped beam headlamps remain on
temporarily, after switching off the vehi-
cle's ignition, to make the driver's exit
easier in poor light.
Activation
With the ignition off, activate a
" h e a d l a m p fl a s h " u s i n g s t a l k B .
A s e c o n d " h e a d l a m p fl a s h " s w i t c h e s
the function off again.
Switching off
The "guide-me-home" lighting is
switched off automatically following the
door locking command, after a given
time. Activation
Turn ring A to the "AUTO" position.
The automatic lighting is accompanied
by a message on the multifunction
screen.
In fog or snow, the sunshine sensor
m a y d e t e c t s u f fi c i e n t l i g h t . T h e r e f o r e ,
the lighting will not be switched on auto-
matically. The dipped beam headlamps
must be switched on manually.
Deactivation
Turn ring A to a position other than
"AUTO" . Switching off is accompa-
nied by a message on the multifunction
screen. Operating fault
In the event of a malfunction of
the sunshine sensor, the light-
ing comes on accompanied by
the service warning lamp, an
audible signal and a message on the
multifunction screen.
Have it checked by a PEUGEOT dealer.
Page 86 of 207
!
VISIBILITY
Do not cover the sunshine sensor,
located in the centre of the wind-
screen behind the rear view mirror;
the associated functions would no
longer be controlled.
Coupling with the "Guide-me-home"
lighting
Association with the automatic illumination of
headlamps provides the "guide-me-home"
lighting with the following additional options:
-
selection of the lighting duration to 15, 30
or 60 seconds in the vehicle parameters
o n t h e m u l t i f u n c t i o n s c r e e n c o n fi g u r a -
tion menu,
- automatic activation of "guide-me- home" lighting when automatic illumi-
nation of headlamps is in operation.
Automatic illumination of headlamps
The sidelamps and dipped beam head-
lamps are switched on automatically, with-
out any action on the part of the driver,
when a low level of external light is detect-
e d ( s e n s o r b e h i n d t h e r e a r v i e w m i r r o r ) .
A s s o o n a s t h e b r i g h t n e s s r e t u r n s t o a s u f fi c i e n t
level, the lighting is switched off automatically.
"Guide-me-home" lighting
The dipped beam headlamps remain on
temporarily, after switching off the vehi-
cle's ignition, to make the driver's exit
easier in poor light.
Activation
With the ignition off, activate a
" h e a d l a m p fl a s h " u s i n g s t a l k B .
A s e c o n d " h e a d l a m p fl a s h " s w i t c h e s
the function off again.
Switching off
The "guide-me-home" lighting is
switched off automatically following the
door locking command, after a given
time. Activation
Turn ring A to the "AUTO" position.
The automatic lighting is accompanied
by a message on the multifunction
screen.
In fog or snow, the sunshine sensor
m a y d e t e c t s u f fi c i e n t l i g h t . T h e r e f o r e ,
the lighting will not be switched on auto-
matically. The dipped beam headlamps
must be switched on manually.
Deactivation
Turn ring A to a position other than
"AUTO" . Switching off is accompa-
nied by a message on the multifunction
screen. Operating fault
In the event of a malfunction of
the sunshine sensor, the light-
ing comes on accompanied by
the service warning lamp, an
audible signal and a message on the
multifunction screen.
Have it checked by a PEUGEOT dealer.
Page 87 of 207
i
VISIBILITY
80
STATIC DIRECTIONAL LIGHTING
When the dipped or main beam headlam-
ps are on, this function enables the beam
to light the inside of the turn with an addi-
tional angle of approximately 30°.
The use of this lighting is optimum above
all at low and average speed (city driving,
w i n d i n g r o a d s , . . . ) .
with directional lighting
without directional lighting Programming
Switching on
The system is switched on from a certain
speed and a certain angle of rotation of the
steering wheel.
Operating fault The function is activated or
deactivated via the multi-
f u n c t i o n s c r e e n c o n fi g u r a -
tion menu.
This function is activated
by default.
In the event of a malfunction,
t h i s w a r n i n g l a m p fl a s h e s o n
the instrument panel, accom-
panied by a message on the
multifunction screen.
Have it checked by a PEUGEOT dealer.
HEADLAMP ADJUSTMENT
The initial setting is position "0" .
To avoid causing a nuisance to other
road users, the height of the headlamps
should be adjusted in relation to the
load in the vehicle.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 4 people.
2. 4 people + maximum authorised
load.
3. Driver + maximum authorised load.
Switching off
The system is switched off below a certain
angle of rotation of the steering wheel.
It is switched off when reverse gear is
engaged.
Page 88 of 207
i
i
VISIBILITY
81
WIPER CONTROL STALK
System for the selection and control of
the various windscreen wiping modes
permitting the dispersal of rain and
cleaning.
The vehicle's windscreen wipers are
designed to gradually improve the driv-
er's visibility in relation to the weather
conditions. Manual controls
The wiping commands are made directly
by the driver using stalk
A .
f a s t ( h e a v y r a i n ) ,
n o r m a l ( m o d e r a t e r a i n ) ,
intermittent (in proportion to
t h e s p e e d o f t h e v e h i c l e ) ,
off,
s i n g l e w i p e ( p r e s s d o w n w a r d s ) ,
Model with intermittent wiping
Windscreen wipers
A. wiping speed selection control: Windscreen and headlamp
wash
Pull the windscreen wiper stalk to-
wards you.
The headlamp wash is only activate if
the dipped headlamps are on .
With daytime running lamps, to
activate the headlamp wash, posi-
tion the lighting stalk in the dipped
beam position.
O n v e h i c l e s fi t t e d w i t h d i g i t a l a i r
conditioning, any action on the
windscreen wash control results in
temporary closing of the air intake
to avoid odours inside the passen-
ger compartment.
Automatic wiping is not available
on the 207CC at present.
Page 124 of 207
115
PETROL ENGINES
T h e c a p s a n d c o v e r s p r o v i d e a c c e s s f o r c h e c k i n g t h e l e v e l s o f t h e v a r i o u s fl u i d s a n d t o r e p l a c e c e r t a i n c o m p o n e n t s .
1. Coolant reservoir.
2. P a s s e n g e r c o m p a r t m e n t fi l t e r .
3. Screenwash and headlamp wash
reservoir.
4. A i r fi l t e r .
5. B r a k e fl u i d r e s e r v o i r .
6. Fusebox.
7. Battery.
8. Engine oil dipstick.
9. E n g i n e o i l fi l l e r c a p .
Page 125 of 207
116
DIESEL ENGINE
T h e c a p s a n d c o v e r s p r o v i d e a c c e s s f o r c h e c k i n g t h e l e v e l s o f t h e v a r i o u s fl u i d s , t o r e p l a c e c e r t a i n c o m p o n e n t s a n d t o p r i m e
the fuel system.
1. Coolant reservoir.
2. P a s s e n g e r c o m p a r t m e n t fi l t e r .
3. Screenwash and headlamp wash
reservoir.
4. Priming pump.
5. B r a k e fl u i d r e s e r v o i r .
6. Fusebox.
7. Battery.
8. Engine oil dipstick.
9. E n g i n e o i l fi l l e r c a p .
10. A i r fi l t e r .
Page 126 of 207
117
CHECKING LEVELS
Check all of these levels regularly and
top them up if necessary, unless other-
wise indicated.
I f a l e v e l d r o p s s i g n i fi c a n t l y , h a v e t h e
corresponding system checked by a
PEUGEOT dealer.
Take care when working under the bon-
net, as some parts of the engine can be
extremely hot (risk of burns). Brake fluid level
To avoid any risk of scalding, unscrew
the cap by two turns to allow the pres-
sure to drop. When the pressure has
dropped, remove the cap and top up
the level.
Oil level The reading will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
The check is carried out either when
the ignition is switched on using the oil
level indicator on the instrument panel,
or using the dipstick. T h e b r a k e fl u i d l e v e l s h o u l d b e
close to the "MAX" mark. If it is
not, check the brake pad wear.
C h a n g i n g t h e b r a k e fl u i d
Refer to the Warranty and Maintenance
Record for details of the interval for this
operation.
Coolant level The coolant level should be
close to the "MAX" mark but
should never exceed it.
When the engine is warm, the
temperature of the coolant is regulated
by the fan. This can operate with the ig-
nition off.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h a
p a r t i c l e e m i s s i o n fi l t e r , t h e f a n m a y
operate after the vehicle has been
s w i t c h e d o f f , e v e n i f t h e e n g i n e i s
cold.
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying
out any work. Screenwash and headlamp
wash * fluid
The minimum level of this
fl u i d i s i n d i c a t e d b y a n a u d i b l e
signal and a message on the
multifunction screen.
Top up the level when you stop the
vehicle.
* According to country.
Changing the engine oil
Refer to the Warranty and Maintenance
Record for details of the interval for this
operation.
In order to maintain the reliability of the
engine and emission control system,
the use of additives in the engine oil is
prohibited.
O i l s p e c i fi c a t i o n
The oil must correspond to your engine
and conform to the manufacturer's
recommendations. F l u i d s p e c i fi c a t i o n
T h e b r a k e fl u i d m u s t c o n f o r m t o t h e
manufacturer's recommendations and
f u l fi l t h e D O T 4 s t a n d a r d s .
Changing the coolant
The coolant does not have to be
changed.
F l u i d s p e c i fi c a t i o n
The coolant must conform to the manu-
facturer's recommendations.
F l u i d s p e c i fi c a t i o n
To guarantee optimum cleaning and
avoid freezing, plain water should not
b e u s e d t o t o p u p o r r e p l a c e t h i s fl u i d .