2010 NISSAN TIIDA WIRING

P0443 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-287
< COMPONENT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Wiring DiagramINFOID:0000000005398447
Diagnosis ProcedureINFOID:0000000005398448
1.CHECK EVAP CANISTER PURG
E VOLUME CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect EVAP canister purge volume control solenoid valve harness connector.
3. Turn ignition switch ON.
ABBWA0351GB
Revision: January 20102010 Versa

EC-292
< COMPONENT DIAGNOSIS >[HR16DE]
P0444, P0445 EVAP CANISTER P
URGE VOLUME CONTROL SOLENOID
VALVE
Wiring Diagram
INFOID:0000000005398452
Diagnosis ProcedureINFOID:0000000005398453
1.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect EVAP canister purge volume control solenoid valve harness connector.
3. Turn ignition switch ON.
BBWA3000E
Revision: January 20102010 Versa

EC-296
< COMPONENT DIAGNOSIS >[HR16DE]
P0447 EVAP CANISTER VENT CONTROL VALVE
Wiring Diagram
INFOID:0000000005398457
Diagnosis ProcedureINFOID:0000000005398458
1.INSPECTION START
Do you have CONSULT-III?
Do you have CONSULT-III?
AABWA0310GB
Revision: January 20102010 Versa

EC-302
< COMPONENT DIAGNOSIS >[HR16DE]
P0448 EVAP CANISTER VENT CONTROL VALVE
Wiring Diagram
INFOID:0000000005398462
Diagnosis ProcedureINFOID:0000000005398463
1.CHECK RUBBER TUBE
1. Turn ignition switch OFF.
2. Disconnect rubber tube connected to EV AP canister vent control valve.
3. Check the rubber tube for clogging.
AABWA0310GB
Revision: January 20102010 Versa

P0452 EVAP CONTROL SYSTEM PRESSURE SENSOREC-311
< COMPONENT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Wiring DiagramINFOID:0000000005398471
Diagnosis ProcedureINFOID:0000000005398472
1.CHECK GROUND CONNECTION
1. Turn ignition switch OFF.
2. Check ground connections E15, E24. Refer to EC-119, "
Ground Inspection".
Is the inspection result normal?
AABWA0311GB
Revision: January 20102010 Versa

EC-318
< COMPONENT DIAGNOSIS >[HR16DE]
P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
Wiring Diagram
INFOID:0000000005398476
Diagnosis ProcedureINFOID:0000000005398477
1.CHECK GROUND CONNECTION
1. Turn ignition switch OFF.
2. Check ground connections E15, E24. Refer to EC-119, "
Ground Inspection".
Is the inspection result normal?
AABWA0311GB
Revision: January 20102010 Versa

P0607 ECMEC-351
< COMPONENT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0607 ECM
DescriptionINFOID:0000000005398514
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each
control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
DTC LogicINFOID:0000000005398515
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check DTC.
Is DTC detected?
YES >> Go to EC-351, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000005398516
1.INSPECTION START
1. Turn ignition switch ON.
2. Erase DTC. Refer to “How to Erase DTC and 1st Trip DTC” in EC-84, "
Diagnosis Description".
3. Perform DTC CONFIRMATION PROCEDURE. Refer to EC-351, "
DTC Logic".
4. Check DTC.
Is the DTC P0607 displayed again?
YES >> GO TO 2.
NO >> INSPECTION END
2.REPLACE ECM
1. Replace ECM.
2. Perform EC-23, "
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
ment".
>> INSPECTION END
DTC No. Trouble diagnosis name DTC detecting conditionPossible cause
P0607 CAN communication bus When detecting error during the initial diagnosis
of CAN controller of ECM.
•ECM
Revision: January 20102010 Versa

P0643 SENSOR POWER SUPPLYEC-353
< COMPONENT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Wiring DiagramINFOID:0000000005398518
Diagnosis ProcedureINFOID:0000000005398519
1.CHECK GROUND CONNECTION
1. Turn ignition switch OFF.
2. Check ground connections E15, E24. Refer to EC-119, "
Ground Inspection".
Is the inspection result normal?
BBWA2649E
Revision: January 20102010 Versa