2010 MITSUBISHI OUTLANDER lock

Vehicle care and maintenance
7-61
7
2. Turn the socket (B) counterclockwise to remove it. 3. Pull the bulb out of the socket.
4. To install the bulb, perform the removal steps in reverse.*- Front of the vehicle
BK0115300US.book 61 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-62 Vehicle care and maintenance
7
Front turn signal lights
N00943400279
1. When replacing the bulb on the front passenger’s side,
remove the bolt (A) holding down the washer fluid reser-
voir spout and move the spout toward the rear of the vehi-
cle.2. Turn the socket (B) counterclockwise to remove it.*- Front of the vehicle
*- Front of the vehicle
BK0115300US.book 62 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-64 Vehicle care and maintenance
7
Side turn signal lights (on outside rearview mir-
ror) (if so equipped)
N00943500124
NOTE

The side turn signal lights (on outside rearview mirror)
uses an LED instead of the bulb.
Check with an authorized Mitsubishi Motors dealer or a
repair facility of your choice when the light needs to be
repaired or replaced.
Front fog lights
(if so equipped)
N00943600633
1. Turn the bezel (A) counterclockwise to remove it.*- Front of the vehicle
BK0115300US.book 64 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-66 Vehicle care and maintenance
7
3. While holding down the tab (D), pull out the socket (E). 4. Turn the bulb (F) counterclockwise to remove it.
BK0115300US.book 66 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-68 Vehicle care and maintenance
7
2. Turn the socket and bulb assembly counterclockwise to
remove it.NOTE

The tail and stop light uses an LED instead of the bulb.
Check with an authorized Mitsubishi Motors dealer or a
repair facility of your choice when the light needs to be
repaired or replaced.3. Pull the bulb out of the socket.
B- Tail and stop light (LED) - cannot be replaced
C- Rear turn-signal light
BK0115300US.book 68 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-70 Vehicle care and maintenance
7
3. Turn the socket (A) counterclockwise to remove it. 4. Pull the bulb out of the socket.
5. To install the bulb, perform the removal steps in reverse.
BK0115300US.book 70 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-72 Vehicle care and maintenance
7
4. Remove the socket and bulb assembly (C) together by
turning it counterclockwise, and then remove the bulb by
pulling it out.
5. To install the bulb, perform the removal steps in reverse.
NOTE

When mounting the light unit, align the pins (D) on the
light unit with the hole in the body.
BK0115300US.book 72 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-78 Vehicle care and maintenance
7
3. To install the bulb, perform the removal steps in reverse.NOTE

Before replacing the bulb, put the dome light (rear)/cargo
room light switch into the “OFF” position.


When mounting the lens, align the tabs (B) with the holes
on the vehicle body.
Glove compartment light
N00954200062
1. Turn the socket (A) counterclockwise to remove it.
BK0115300US.book 78 ページ ２００９年７月１６日　木曜日　午前９時１３分