2010 MITSUBISHI LANCER RALLIART brake light

3-136 Features and controls
3
If the warning light / display comes on while driv-
ing
N00531700503
If only the anti-lock braking system warning light / dis-
play comes on
Avoid hard braking and high-speed driving. Stop the vehi-
cle in a safe place.
Test the system by restarting the engine and driving at a
speed of about 12 mph (20 km/h) or higher.
If the warning light / display then remain off during driv-
ing, there is no problem.
However, if the warning light / display do not disappear,
or if they come on again when the vehicle is driven, have
the vehicle checked by an authorized Mitsubishi Motors
dealer or repair facility of your choice as soon as possible.
CAUTION
!
Any of the following warning light/display behavior
indicates that the anti-lock braking system is not
functioning and only the standard brake system is
working. (The standard brake system will still work
properly.) If this happens, take your vehicle to an
authorized Mitsubishi Motors dealer or a repair
facility of your choice as soon as possible.
• When the ignition switch is in the “ON” position,
the warning light does not come on or it remains
on and does not go off
• The warning light comes on while driving
• The warning display appears while driving
BK0102103US.book 136 ページ ２００９年１０月２６日　月曜日　午後１時３８分

Features and controls
3-137
3
If the anti-lock braking system warning light / display
and brake warning light / display come on at the same
timeWarning light

Warning display type 1

Warning display type 2

The anti-lock braking system and brake force distribution func-
tion may not work, so hard braking could make the vehicle
unstable.
Avoid hard braking and high-speed driving. Stop the vehicle in
a safe place and contact an authorized Mitsubishi Motors
dealer or repair facility of your choice.NOTE
The anti-lock braking system warning light and brake
warning light illuminate at the same time and the warning
displays appear alternately on the information screen in
the multi-information display.
After driving on icy roads
N00529200022
After driving on snow or icy roads, remove any snow and ice
which may have been left around the wheels. On vehicles that
have an anti-lock braking system, be careful not to damage the
wheel speed sensors (A) or the cables located at each wheel.Front
BK0102103US.book 137 ページ ２００９年１０月２６日　月曜日　午後１時３８分

Features and controls
3-139
3
NOTE
An operation noise may be emitted from the engine com-
partment in the following situations. The sound is associ-
ated with checking the operations of the ASC. At this
time, you may feel a shock from the brake pedal if you
depress it. These do not indicate a malfunction.
• When the ignition switch is set to the “ON” position.
• When the vehicle is driven for a while after the engine is
turned on.

When the ASC is activated, you may feel a vibration in
the vehicle body or hear a whining sound from the engine
compartment.
This indicates that the system is operating normally. It
does not indicate a malfunction.

When the anti-lock braking system warning light is illu-
minated, the ASC is not active.
Traction control function
N00559200034
On slippery surfaces, the traction control function prevents the
drive wheels from spinning excessive, thus helping the vehicle
to start moving from a stopped condition. It also provides suffi-
cient driving force and steering performance as the vehicle
turns while pressing the acceleration pedal.Skid control function
N00559300035
The skid control function is designed to help the driver main-
tain control of the vehicle on slippery roads or during rapid
steering maneuvers. It works by controlling the engine output
and the brake on each wheel.NOTE
The skid control function operates at speeds of about 9
mph (15 km/h) or higher.
CAUTION
!
When driving a vehicle on a snowy or icy road, be
sure to install snow tires and drive the vehicle at
moderate speeds.
BK0102103US.book 139 ページ ２００９年１０月２６日　月曜日　午後１時３８分

Features and controls
3-149
3
To temporarily decrease the speedApply the brakes to decrease the speed. To return to the previ-
ously set speed, press the “ACC RES” switch (C). Refer to “To
resume the set speed” on page 3-151.
To deactivate
N00518800493
The cruise control can be turned off as follows:

Press the “ON OFF” switch (A). (Cruise control will be
turned off.)

Press the “CANCEL” switch (D).

Depress the brake pedal or lightly tap it.
Type 1
Type 2
Type 1
Type 2
BK0102103US.book 149 ページ ２００９年１０月２６日　月曜日　午後１時３８分

3-184 Features and controls
3
Changing the function settings (With ignition
switch in the “ON” position)
N00556800071
1. Park your vehicle in a safe place.
Fully apply the parking brake and move the shift lever
into the “N” position (manual transaxle), the selector lever
{continuously variable transmission (CVT)} or the gear-
shift lever (Twin Clutch SST) into the “P” position.
2. When you lightly press the multi-information meter
switch, the information screen changes to the function set-
ting screen.
Refer to “Information screen (With ignition switch in the
“ON” position)” on page 3-172.3. Press and hold the multi-information meter switch (for
about 2 seconds or more) to switch from the setting mode
screen to the menu screen.
Type 1 Type 2
CAUTION
!
For safety, stop the vehicle before operating.
While driving, even if you operate the multi-infor-
mation meter switch, the function setting screen is
not displayed.Type 1
Type 2
BK0102103US.book 184 ページ ２００９年１０月２６日　月曜日　午後１時３８分

Features and controls
3-197
3 Indicator light, warning light, and information screen display list
N00557700035
Indicator and warning light list
N00557800111
Type 1Type A Type B1- Turn signal indicator/hazard warning light → P.3-211
2- High beam indicator → P.3-211
3- Position indicator → P.3-211
4- Front fog light indicator (if so equipped) → P.3-211
5- Seat belt reminder/warning light → P.2-18
6- Anti-lock braking system warning light (if so equipped)
→ P.3-135
7- Charging system warning light → P.3-213
8- Brake warning light → P.3-211
9- Cruise control indicator (if so equipped) → P.3-14410- Supplemental Restraint System (SRS) warning light
→ P.2-43
11- Engine malfunction indicator (“SERVICE ENGINE SOON”
or “Check engine light”) → P.3-212
12- Tire pressure monitoring system warning light → P.3-153
13- Information screen display list → P.3-199
BK0102103US.book 197 ページ ２００９年１０月２６日　月曜日　午後１時３８分

3-198 Features and controls
3
Type 2Type A Type B1- Position indicator → P.3-211
2- High beam indicator → P.3-211
3- Charging system warning light → P.3-213
4- Turn signal indicator/hazard warning light → P.3-211
5- Front fog light indicator → P.3-211
6- Anti-lock braking system warning light → P.3-135
7- Tire pressure monitoring system warning light → P.3-153
8- Brake warning light → P.3-211
9- Cruise control indicator → P.3-144
10- Seat belt reminder/warning light → P.2-18
11- Supplemental Restraint System (SRS) warning light
→ P.2-4312- Engine malfunction indicator (“SERVICE ENGINE SOON”
or “Check engine light”) → P.3-212
13- Active Stability Control (ASC) indicator → P.3-141
14- Information screen display list → P.3-199
BK0102103US.book 198 ページ ２００９年１０月２６日　月曜日　午後１時３８分

3-204 Features and controls
3

Immobilizer is registered.
Refer to “Electronic immobilizer
(Anti-theft starting system)” on
page 3-5, 3-42.

The brake fluid level is low.

There is a fault in the brake system.
Park the vehicle in a safe place and
contact an authorized Mitsubishi
Motors dealer or a repair facility of
your choice for assistance.
Refer to “Brake warning display”
on page 3-214.

There is a fault in the Anti-lock
braking system.
Avoid sudden braking and high-
speed driving, park the vehicle in a
safe place, and take corrective mea-
sures. Refer to “Anti-lock braking
system warning light/display” on
page 3-135.

The tire pressure in one of the tires
(except spare tire) is low.
Refer to “Tire Pressure Monitoring
System” on page 3-152.

There is a fault in the Tire Pressure
Monitoring System.
Refer to “Tire Pressure Monitoring
System” on page 3-152.
Screen type1
Screen type 2
Cause
Do this (Reference)
BK0102103US.book 204 ページ ２００９年１０月２６日　月曜日　午後１時３８分