2010 MITSUBISHI ECLIPSE length

3-42 Features and controls
3
NOTE
When you insert the locking pins (D) into the holes (G),
they may be stiff. If this happens, adjust each locking pin
(D) to a length that enables secure retention of the wind
deflector. To adjust the length of each locking pin (D),
turn the end of the locking pin using a screwdriver.6. Raise the top frame to the full upright position as illus-
trated.
BK0098300US.book 42 ページ ２００８年１２月８日　月曜日　午前１１時３７分

Features and controls
3-77
3
“N” NEUTRALAt this position, the transaxle is disengaged. It is the same as
the neutral position on a manual transaxle and should be used
when the vehicle is not moving for an extended length of time
during driving, such as in a traffic jam.
“D” DRIVEThis position is used for most city and highway driving. Engine
shifting and braking are done automatically as needed, depend-
ing on road conditions.NOTE
For information on manual gate operation, please refer to
“Sports mode” on page 3-78.
WA R N I N G
!
Never move the selector lever to the “N” (NEU-
TRAL) position while driving since you could acci-
dentally slip it into the “P” (PARK) or
“R”(REVERSE) position, damaging the transaxle.
To prevent the vehicle from rolling when stopped on
a slope, the engine should be started in the “P”
(PARK) position, not in “N” (NEUTRAL) position.
Always keep your foot on the brake pedal when the
vehicle is in “N” (NEUTRAL) position, or when
shifting into or out of “N” (NEUTRAL) position, to
prevent rolling.
BK0098300US.book 77 ページ ２００８年１２月８日　月曜日　午前１１時３７分

Vehicle care and maintenance
7-15
7 Brake fluid/Clutch fluid
(if so equipped)
N00938700229
The brake fluid and the clutch fluid share the reservoir tank.To check the fluid levelThe fluid level must be between the “MAX” and “MIN” marks
on the reservoir.
The fluid level is monitored by a float. When the brake fluid
level falls below the “MIN” mark, the brake fluid warning
lamp lights up.
The fluid level falls slightly with wear of the brake pads, but
this does not indicate any abnormality.
The fluid in the master cylinder should be checked when doing
other work under the engine hood. The brake system should
also be checked for leaks at the same time.If the fluid level falls markedly in a short length of time, it indi-
cates leaks from the brake system.
If this occurs, have the vehicle checked by an authorized Mit-
subishi Motors dealer or a repair facility of your choice.
Fluid typeUse the brake fluid conforming to DOT 3 or DOT 4. The reser-
voir cap must be tightly sealed to keep dirt and water out.
CAUTION
!
Do not let any petroleum-based fluid touch, mix
with, or get into the brake fluid. This will damage
the seals.
Be careful when handling brake fluid. It can damage
painted surfaces.
Use only the listed brake fluid. Different brands of
brake fluid have different additives, and these can
cause a chemical reaction. Do not mix brands of
brake fluid.
Keep the reservoir tank cap closed to keep the brake
fluid from evaporating.
BK0098300US.book 15 ページ ２００８年１２月８日　月曜日　午前１１時３７分

9-6 Specifications
9Vehicle dimensions
N01147500411
ECLIPSE
ECLIPSE SPYDEROverall length 180.4 in (4,583 mm) Overall width 72.2 in (1,835 mm) Overall height
Vehicles with
17 inch tires53.5 in (1,358 mm)Vehicles with
18 inch tires53.8 in (1,366 mm)
Wheel base 101.4 in (2,575 mm) Overall length 180.4 in (4,583 mm) Overall width 72.2 in (1,835 mm) Overall height
Vehicles with
17 inch tires54.4 in (1,381 mm)Vehicles with
18 inch tires54.7 in (1,389 mm)
Wheel base 101.4 in (2,575 mm) BK0098300US.book 6 ページ ２００８年１２月８日　月曜日　午前１１時３７分