2010 MINI COOPER wheel bolts

Replacing components
132
Wrap the empty sealant bottle in suitable mate-
rial to avoid dirtying the cargo bay. Stow the
Mobility System back in the vehicle.
Distributing the sealant
Immediately drive approx. 3 mls/5 km to evenly
distribute the sealant.
Do not exceed speeds of 50 mph/
80 km/h.
If possible, do not drop below 10 mph/
20 km/h.<
Correcting the tire inflation pressure
1.After driving approx. 3 mls/5 km or ten min-
utes, stop at a suitable location.
2.Screw the connection hose 2 of the com-
pressor directly onto the tire valve.
3.Insert the plug 3 into the power socket in the
vehicle interior.
4.Correct the inflation pressure to 26 psi/
180 kPa. With the engine running:
>To increase the inflation pressure: switch on
the compressor. To check the current infla-
tion pressure, switch off the compressor.
Do not run the compressor for longer
than 10 minutes; otherwise, the
device will overheat and possibly be
damaged.<
>To decrease the inflation pressure: press the
release button 5.
If the tire cannot maintain the inflation
pressure, drive the vehicle again, refer to
Distributing the sealant. Then repeat steps
1to4.
If an inflation pressure of 26 psi/180 kPa still
cannot be reached, the tire is too heavily dam-
aged. Contact the nearest MINI dealer.<
Driving on
Do not exceed the permitted maximum
speed of 50 mph/80 km/h; doing so may
result in an accident.<
Replace the defective tire as soon as possible
and have the new wheel/tire assembly bal-
anced.Have the Mobility System refilled.
Changing wheels
Space-saver spare tire*
To change a space-saver spare tire, proceed as
follows:
>Remove the space-saver spare tire,
page133
>Prepare for tire change, page133
>Jack up vehicle, page134
>Mount space-saver spare tire, page134
>Tighten lug bolts, page134
>Drive with space-saver spare tire, page133
Tire change set for a space-saver
spare tire*
On vehicles with a space-saver spare tire, the
tire change set with onboard tools is stored
under the floor mat in the cargo bay.
1Chock, folding
2Hub cover remover
3Wheel stud wrench
4Vehicle jack
5Special wrench for removing the space-
saver spare tire
6Flat screwdriver/Phillips screwdriver
7Towing eyelet
8Lifting handle
The onboard vehicle tool kit includes a pouch
with a plastic bag in which you can place the
damaged wheel.

Replacing components
134
Only change the tire when parked on a surface
that is level, firm and not slippery.
The vehicle or the jack could slip sideways on
soft or slippery support surfaces, such as snow,
ice, flagstones, etc.
Do not use a wooden block or similar object as a
support base for the jack, as this would prevent
it from extending to its full support height and
reduce its load-carrying capacity.
Do not lie under the vehicle or start the engine
when the vehicle is supported by the jack; other-
wise, there is a risk of fatal injury.<
1.Place the foldable chock
* behind the front
wheel on the other side of the vehicle or in
front of the wheel if the vehicle is on an
incline. If the wheel is changed on a surface
with a more severe slope, take additional
precautions to secure the vehicle from
rolling.
2.Uncover the lug bolts if necessary.
If the wheel is equipped with a hub cover,
pry it off using the screwdriver from the tire
change kit.
3.Loosen the lug bolts by a half turn.
Jacking up the vehicle
The vehicle jack is designed for changing
wheels only. Do not attempt to raise
another vehicle model with it or to raise any load
of any kind. To do so could cause accidents and
personal injury.<
1.Place the jack at the jacking point closest to
the wheel.The jack base must be perpendicular to the
surface beneath the jacking point.
2.During jacking up, insert the jack head in the
square recess of the jacking point.
3.Jack the vehicle up until the wheel you are
changing is raised off the ground.
Mounting the space-saver spare tire
1.Unscrew the lug bolts and remove the
wheel.
2.Remove accumulations of mud or dirt from
the mounting surfaces of the wheel and
hub. Clean the lug bolts.
3.Lift the new wheel into place.
4.Screw at least two lug bolts finger-tight into
opposite bolt holes.
5.Screw in the remaining bolts.
6.Tighten all the lug bolts firmly in a diagonal
pattern.
7.Lower the vehicle.
8.Remove the jack.
Tightening the lug bolts
Tighten the lug bolts in a diagonal pattern.
Immediately have the wheels checked
with a calibrated torque wrench to ensure
that the lug bolts are firmly seated. Otherwise,
incorrectly tightened lug bolts can present a
safety hazard.<
Tightening torque: 103.3 lb ft or 140 Nm.
Replace the defective tire as soon as possible
and have the new wheel/tire assembly bal-
anced.

From A to Z
168
Storage area
– cargo bay94
Storage compartment, front
passenger side88
Storage compartments88
Storage space
– storage compartments88
Storage space, refer to
– Luggage compartment in the
MINI Convertible94
Storing the vehicle124
Storing tires115
Stowage, refer to Storage
compartments88
Summer tires, refer to Wheels
and tires104
Switches, refer to Cockpit10
Switching off
– engine47
Switching off the engine
– start/stop button46
Switching the cooling function
on and off84
Symbols4
T
Tachometer55
Tail lamp, refer to Tail
lamps128
– replacing bulb128
Tail lamps128
Tailgate26
– Comfort Access29
– opening from outside26
– opening/closing26
– unlocking with remote
control23
Tank volume, refer to
Capacities158
Technical data154
Technical modifications5
Telephone
– installation location, refer to
Center armrest87
– refer to separate Owner's
ManualTelephone call, refer to the
Owner's Manual for the
telephone
Temperature display
– ice warning55
– outside temperature55
– setting the units59
Temperature of coolant, refer
to Coolant temperature55
Temperature setting
– air conditioner81
– automatic climate control83
Tensioning straps, refer to
Securing cargo96
The individual vehicle4
Third brake lamp, refer to
Center brake lamp129
Three-point safety belt40
Through-loading system95
Tightening the lug bolts
– keys132
– torque134,135
Tightening torque, refer to
Tightening the lug bolts134
Tire change set
– space-saver spare tire132
Tire failure
– Flat Tire Monitor68
– indicator/warning lamp68
– MINI Mobility System130
– run-flat tires68
– space-saver spare tire132
– Tire Pressure Monitor69
Tire inflation pressure104
– loss68
– space-saver spare tire104
Tire Pressure Monitor TPM69
– limitations of system69
– resetting system69
– warning lamp70
Tire pressure monitoring, refer
to Flat Tire Monitor67
Tire Quality Grading112Tires
– age113
– breaking in92
– changing, refer to Changing
wheels132
– condition113
– damage113
– inflation pressure104
– inflation pressure loss70
– minimum tread depth113
– new tires114
– pressure monitoring, refer to
Flat Tire Monitor67
– pressure monitoring, refer to
Tire Pressure Monitor
TPM69
– puncture68
– run-flat tires114
– size112
– wear indicators, refer to
Minimum tread depth113
– winter tires115
Tires with safety features, refer
to Run-flat tires114
Tools, refer to Onboard vehicle
tool kit125
Torque154
– lug bolts134
Tow bar138
Tow fitting137
– screw thread138
Tow fittings for tow-starting
and towing away137
Tow rope138
Towing137
– car with automatic
transmission138
– methods138
Tow-starting137
TPM, refer to Tire Pressure
Monitor69
Track width, refer to
Dimension155
Traction control, refer to
– Dynamic Stability Control
DSC65