2010 MERCEDES-BENZ ML550 ESP

Engine ΜL 350Bore3.66 in (92.90 mm)Stroke3.39 in (86.00 mm)Total piston
displacement213.5 cu in
(3 498 cm 3
)Compression
ratio10.7:1Output acc. to
SAE J 1349 37268 hp/6
000 rpm
(200 kW/6 000 rpm)Maximum torque
acc. to SAE J 1349258 lb-ft/
2 400 - 5 000 rpm
(350 Nm/
2 400 - 5 000 rpm)Maximum engine
speed6 500 rpmFiring order1-4-3-6-2-5Poly-V-belt2 398 mmElectrical system ML 350Alternator14 V/180 AStarter motor12 V/1.4 kWBattery12 V/70 AhSpark plugs, typeBosch Y 7 MPP33Spark plugs,
electrode gap0.031 in (0.8 mm)Spark plugs,
tightening torque15 - 18 lb-ft
(20 - 25 Nm)Main dimensions ΜL 350Overall vehicle
length188.5 in (4 788 mm)Overall vehicle
width 3883.6 in (2
124 mm)Overall vehicle
height71.5 in (1 815 mm)Wheelbase114.8 in (2 915 mm)Track, front64.0 in (1 627 mm)Track, rear64.1 in (1 629 mm)Ground clearance8.3 in (210 mm)Turning circle39.0 ft (11.6 m)Weights ΜL 350Roof loadmax. 220 lb (100 kg)
Vehicle specification ML 350 4MATIC
(164.186)
The quoted data apply only to the standard
vehicle. Contact an authorized Mercedes-
Benz Center for the corresponding data of all
special bodies and special equipment.
Engine ΜL 350 4MATICEngine, type272Mode of operation4-stroke engine,
gasoline injectionNo. of cylinders6Bore3.66 in (92.90 mm)Stroke3.39 in (86.00 mm)Total piston
displacement213.5 cu in
(3 498 cm 3
)37 Premium fuel required. Performance may vary with fuel octane rating.
38 Exterior rear view mirrors folded out.Vehicle specification ML 350 4MATIC (164.186)349Technical data164_AKB; 7; 31, en-USd2ureepe,Version: 2.11.8.12009-09-11T12:07:36+02:00 - Seite 349Z

Engine ΜL 350 4MATICCompression
ratio10.7:1Output acc. to
SAE J 1349 39268 hp/6
000 rpm
(200 kW/6 000 rpm)Maximum torque
acc. to SAE J 1349258 lb-ft/
2 400 - 5 000 rpm
(350 Nm/
2 400 - 5 000 rpm)Maximum engine
speed6 500 rpmFiring order1-4-3-6-2-5Poly-V-belt2 398 mmElectrical system ML 350 4MATICAlternator14 V/180 AStarter motor12 V/1.4 kWBattery12 V/70 AhSpark plugs, typeBosch Y 7 MPP33Spark plugs,
electrode gap0.031 in (0.8 mm)Spark plugs,
tightening torque15 - 18 lb-ft
(20 - 25 Nm)Main dimensions ΜL 350 4MATICOverall vehicle
length188.5 in (4 788 mm)Overall vehicle
width 4083.6 in (2
124 mm)Overall vehicle
height71.5 in (1 815 mm) 4169.8 - 73.0 in
(1 774 - 1 854 mm) 42Main dimensions ΜL 350 4MATICWheelbase114.8 in (2
915 mm)Track, front64.0 in (1 627 mm)Track, rear64.1 in (1 629 mm)Ground clearance8.3 in (210 mm) 417.3 - 10.3 in
(186 - 261 mm) 42Turning circle39.0 ft (11.6 m)Weights ΜL 350 4MATICRoof loadmax. 220 lb (100 kg)
Vehicle specification ML 550 4MATIC
(164.172)
The quoted data apply only to the standard
vehicle. Contact an authorized Mercedes-
Benz Center for the corresponding data of all
special bodies and special equipment.
Engine ML 550 4MATICEngine, type273Mode of operation4-stroke engine,
gasoline injectionNo. of cylinders8Bore3.86 in (98.00 mm)Stroke3.56 in (90.50 mm)Total piston
displacement333.2 cu in
(5 461 cm 3
)Compression
ratio10.7:139 Premium fuel required. Performance may vary with fuel octane rating.
40 Exterior rear view mirrors folded out.
41 Vehicles with steel suspension.
42 Depending on the set vehicle level (vehicles with air suspension program).350Vehicle specification ML 550 4MATIC (164.172)Technical data
164_AKB; 7; 31, en-USd2ureepe,Version: 2.11.8.12009-09-11T12:07:36+02:00 - Seite 350

Engine ML 550 4MATICOutput acc. to
SAE J 1349 43382 hp/6
000 rpm
(285 kW/6 000 rpm)Maximum torque
acc. to SAE J 1349391 lb-ft/
2 800 - 4 800 rpm
(530 Nm/
2 800 - 4 800 rpm)Maximum engine
speed6 500 rpmFiring order1-5-4-2-6-3-7-8Poly-V-belt2 398 mmElectrical system ML 550 4MATICAlternator14 V/180 AStarter motor12 V/1.4 kWBattery12 V/95 AhSpark plugs, typeNGK PLKR 7ASpark plugs,
electrode gap0.031 in (0.8 mm)Spark plugs,
tightening torque15 - 18 lb-ft
(20 - 25 Nm)Main dimensions ΜL 550 4MATICOverall vehicle
length188.5 in (4 788 mm)Overall vehicle
width 4483.6 in (2
124 mm)Overall vehicle
height71.5 in (1 815 mm) 4569.8 - 73.0 in
(1 774 - 1 854 mm) 46Wheelbase114.8 in (2
915 mm)Main dimensions ΜL 550 4MATICTrack, front63.7 in (1 619 mm)Track, rear63.8 in (1 621 mm)Ground clearance8.3 in (210 mm) 457.3 - 10.3 in
(186 - 261 mm) 46Turning circle39.0 ft (11.6 m)Weights ΜL 550 4MATICRoof loadmax. 220 lb (100 kg)
Vehicle specification ML 63 AMG
(164.177)
The quoted data apply only to the standard
vehicle. Contact an authorized Mercedes-
Benz Center for the corresponding data of all
special bodies and special equipment.
Engine ML 63 AMGEngine, type156Mode of operation4-stroke engine,
gasoline injectionNo. of cylinders8Bore4.02 in (102.20 mm)Stroke3.72 in (94.60 mm)Total piston
displacement378.8 cu in
(6 208 cm 3
)Compression
ratio11.3:1Output acc. to
SAE J 1349 47503 hp/6
800 rpm
(375 kW/6 800 rpm)43
Premium fuel required. Performance may vary with fuel octane rating.
44 Exterior rear view mirrors folded out.
45 Vehicles with steel suspension.
46 Depending on the set vehicle level (vehicles with air suspension program).
47 Premium fuel required. Performance may vary with fuel octane rating.Vehicle specification ML 63 AMG (164.177)351Technical data164_AKB; 7; 31, en-USd2ureepe,Version: 2.11.8.12009-09-11T12:07:36+02:00 - Seite 351Z

Engine ML 63 AMGMaximum torque
acc. to SAE J 1349465 lb-ft/5 200 rpm
( 630 Nm/5 200 rpm)Maximum engine
speed7 200 rpmFiring order1-5-4-2-6-3-7-8Poly-V-belt2 360 mmElectrical system ML 63 AMGAlternator14 V/180 AStarter motor12 V/2.1 kWBattery12 V/95 AhSpark plugs, typeNGK ILZKAR 7A10Spark plugs,
electrode gap0.039 in (1.0 mm)Spark plugs,
tightening torque15 - 18 lb-ft
(20 - 25 Nm)Main dimensions ML 63 AMGOverall vehicle
length189.7 in (4 818 mm)Overall vehicle
width 4883.6 in (2
124 mm)Overall vehicle
height69.5 - 72.6 in
(1 765 - 1 845 mm) 49Wheelbase114.8 in (2
915 mm)Track, front65.5 in (1 664 mm)Track, rear65.6 in (1 667 mm)Ground clearance7.0 - 10.1 in
(177 - 257 mm) 49Turning circle39.0 ft (11.6 m)Weights ML 63 AMGRoof loadmax. 220 lb (100 kg)
Rims and tires
Notes
! Only use tires which have been tested and
approved by Mercedes-Benz. Tires
approved by Mercedes-Benz are developed
to provide best possible performance in
conjunction with the driving safety systems
on your vehicle such as the ABS or the
ESP ®
. Tires specially developed for your
vehicle and tested and approved by
Mercedes-Benz can be identified by finding
the following on the tire’s sidewall:
R MO =
Mercedes-Benz Original
equipment tires
R MOE =
Mercedes-Benz Original Extended
(tires with limited run-flat
characteristics) original equipment tires
Using tires other than those approved by
Mercedes-Benz may result in damage that
is not covered by the Mercedes-Benz
Limited Warranty.
For information on driving with MOExtended
tires, see the “Practical hints” section
( Y page 330).
i Vehicles with MOExtended system are
not factory-equipped with a TIREFIT kit.
When retrofitting with tires that do not have
run-flat characteristics, you should also
equip your vehicle with a TIREFIT kit.
TIREFIT kits are available at any authorized
Mercedes-Benz Center.
! Using tires other than those approved by
Mercedes-Benz can have detrimental
effects, such as
48 Exterior rear view mirrors folded out.
49 Depending on the set vehicle level.352Rims and tiresTechnical data
164_AKB; 7; 31, en-USd2ureepe,Version: 2.11.8.12009-09-11T12:07:36+02:00 - Seite 352

Spare wheel
! Compare the recommended tire inflation pressure for your vehicle with the tire inflation
pressure on the yellow label located on the spare wheel rim.
If the tire inflation pressure on the yellow label on the spare wheel rim differs from the values
given in this Operator’s Manual, inflate the tire to the recommended tire inflation pressure
given on the yellow label on the spare wheel rim.
i Please note that the tire inflation pressure of the spare wheel differs from the tire inflation
pressure of the road tires.
i The ML 350 BlueTEC 4MATIC does not have a spare wheel.ModelML 350 (all models)
ML 550 (all models)ML 63 AMGRim4.0 B x 18 H25.5 B x 19 H2Wheel offset1.58 in (40 mm)0.51 in (13 mm)Minispare tire 58T 155/90 D18 113M
or
T 155/90 R18 113M—Collapsible tire 58—185/85-19 104PRecommended tire
inflation pressure61 psi (4.2 bar)51 psi (3.5 bar)Fuels, coolants, lubricants, etc.
Capacities
Vehicle components and their respective
lubricants must match. Therefore only use
products tested and approved by Mercedes-
Benz.
For information on tested and approved
products, contact an authorized Mercedes-
Benz Center or visit www.mbusa.com (USA
only).
GWarning!
Comply with all valid regulations with respect
to handling, storing, and disposing of service
fluids. Otherwise you could endanger persons
or the environment.
Keep service fluids out of the reach of
children.
For health reasons, you should prevent
service fluids from coming into direct contact
with your skin or clothing.
If a service fluid is swallowed, contact a
physician immediately.58 Must not be used with snow chains.356Fuels, coolants, lubricants, etc.Technical data
164_AKB; 7; 31, en-USd2ureepe,Version: 2.11.8.12009-09-11T12:07:36+02:00 - Seite 356

! Do not fill the tank with gasoline. Do not
blend diesel fuel with gasoline or kerosene.
The fuel system and engine will otherwise
be damaged, which is not covered by the
Mercedes-Benz Limited Warranty.
For further information on diesel fuel pump
labeling, contact an authorized Mercedes-
Benz Center or visit www.mbusa.com (USA
only).
Biodiesel (FAME = Fatty Acid Methyl
Ester) containing fuels
Mercedes-Benz USA approves the use of B5
(standard ULSD which may contain a
maximum of 5% biodiesel) in all Common-rail
injection (CDI) and BlueTEC diesel engines.
Diesel fuels containing a higher percentage of
biodiesel, e.g. B20, as well as straight
biodiesel may cause severe damage to your
engine/fuel system and are not approved.
Please ask your service station personnel for
further information. If the B5 biodiesel blend
is not sufficiently labeled to clearly indicate
that it meets the ULSD standard, please do
not use it.
The Mercedes-Benz Limited Warranty does
not cover damages caused by the use of fuels
not meeting Mercedes-Benz approved fuel
standards.
Gasoline additives (gasoline engine)
A major concern among engine
manufacturers is carbon build-up caused by
gasoline. Mercedes-Benz recommends only
the use of quality gasoline containing
additives that prevent the build-up of carbon
deposits.
After an extended period of using fuels
without such additives carbon deposits can
build up, especially on the intake valves and
in the combustion area, leading to engine
performance problems such as:
R Warm-up hesitation
R Unstable idle
R
Knocking/pinging
R Misfire
R Power loss
In areas where carbon deposits may be
encountered due to lack of availability of
gasoline which contains these additives, the
use of Mercedes-Benz approved additives is
recommended.
Contact an authorized Mercedes-Benz Center
or visit www.mbusa.com (USA only) for a
listing of approved products. Follow
directions on the product label.
Do not blend other fuel additives with fuel.
This only results in unnecessary cost and may
be harmful to the engine operation.
! Damage or malfunction resulting from
poor fuel quality or from blending additional
fuel additives other than those tested and
approved by us for use on Mercedes-Benz
vehicles are not covered by the Mercedes-
Benz Limited Warranty or by any pre-owned
or Extended Limited Warranties.
AdBlue ®
AdBlue ®
is a non-flammable, non-toxic,
colorless and odorless, water-soluble liquid.
! Only use AdBlue ®
complying with
ISO 22241. Do not blend with additives.
! Rinse surfaces that have come into
contact with AdBlue ®
, or remove AdBlue ®
with a moist cloth and cold water
immediately. If AdBlue ®
has crystallized
already, use cold water and a sponge.
AdBlue ®
residues will crystallize and soil
the affected surfaces.
High ambient temperatures
If AdBlue ®
in the reservoir heats up to above
122‡ (50†) for a long period of time, for
example due to direct sunlight, ammonia gas
Fuels, coolants, lubricants, etc.361Technical data164_AKB; 7; 31, en-USd2ureepe,Version: 2.11.8.12009-09-11T12:07:36+02:00 - Seite 361Z