
Displa
ymessages Possible causes/consequences and
M Solutions
J EB
D, ABS
and ESP
inopera‐
tiv eS ee
Owner's
Manual G
Risk of accident
EBD (Electronic Brake-for ceDistribution), ABS, ESP ®
,B AS,
PRE-SAFE ®
,t he HOL Dfunction ,hill start assist and ESP ®
trailer stabilisation are no tavailab ledue to amalfunction. In
addition, the ä,åand! warning lamp sinthe
instrumen tcluster light up and awarning tone sounds.
ATTENTION ASSIST is deactivated.
The brake system continue stofunction normally, but without
the functions listed above. The wheels coul dtherefore lock if
you brake hard, for example.
X Drive on carefully.
X Visit aquali fieds pecialist workshop immediately. J Release
parking
brake You are drivin
gwith the parkin gbrake engaged .Awarning
ton ealso sounds.
X Release th eparking brake. J Br
ake
immedi‐
ately Am
alfunction has occurred while the HOL Dfunction or DIS-
TRONI CPLUSisa ctive.
or
Vehicles with manual transmissio n:with the HOL Dfunction
activated, you have either:
R opened the driver' sdoor and released th eseat belt or
R switched off th eengineor
R opened th ebonnet
At one ma yalso sound at regular intervals. The ton ebecomes
louder if you attempt to lock the vehicle.
You can notstart the engine.
X Paying attention to the traffic situation, immediately
depress the brake peda lfirmly and hold until the display
message disappears.
X Prevent the vehicle from rolling away before you leave it
(Y page 153).
You can restart the engine. 216
Display messagesOn-board computer and displays
BA 20
7ECE ÄJ 2010 /1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00 -Seite 216

Engine
Display messages Possible causes/consequences and
M Solutions
+ To
pup
coolant
See Own‐
er' sM an‐
ual Th
ec oolant leve listoo low.
X Top up th ecoolant ,obser ving the warning note sbefore
doin gso( Ypage 261).
X If th ecoolant needs toppin gupmoreo ften than usual ,have
the engin ecoolant system checked at aqualified specialist
workshop. ? Co
olant
Sto pv ehi‐
cle
Switch
engine off Th
ec oolant is to ohot.
Aw arning ton ealso sounds.
X Pull ove rand sto pthe vehicle safel yand switch off the
engine ,payin gattentio ntoroad and traffic conditions.
X Make sure that the air supply to the radiator is not blocked,
e.g. by snow, slush or ice.
X Wait until the display message disappears befor erestar ting
the engine. Otherwise, there is arisk of engine damage.
X Pay attention to the coolant tempera turedisplay.
X If the temperature increases again, visit aqualified special-
ist worksho pimmediately. Th
ep oly-V-belt ma yhave torn.
X Pull over and stop the vehicle safely and switch off the
engine, paying attention to road and traffic conditions.
X Open the bonnet.
X Check whethe rthe poly-V-belt is tor n.
If the poly-V -belt is torn:
! do not continue driving. The engine could otherwise over-
heat.
X Consult aqualified specialist workshop.
If the poly-V-belt is OK:
X Wait until the display messag edisappears before restarting
the engine. Otherwise, there is arisk of engine damage.
X Pay attention to the coolant tempera turedisplay.
X Visit aqualified specialist workshop. 222
Display messagesOn-board computer and displays
BA 207 ECE ÄJ 2010/1a; 1; 2, en-GB
mkalaf
aV ersion: 3.0.2.11
2010-01-26T13:03:22+01:00
-Seite 222

Displa
ymessages Possible causes/consequences and
M Solutions
? The fan motor is faulty.
X
If th ecoolant tem perature is less than 12 0†,you can
continue drivin gtothe nearest qual ified specialist work-
shop.
X Avoid subjecting th eenginetoh eavy loads, e.g. driving in
mountainous terrain, and stop-star tdriving. # Th
eb attery is not being charged.
Aw arning ton ealso sounds.
Possible causes are:
R af ault yalternator
R at orn poly-V-belt
R am alfunction in the elect ronics
X Pul lover and stop the vehicle safel yand switch off the
engine ,payin gattentio ntoroad and traffic conditions.
X Open the bonnet.
X Check whether the poly-V-belt is tor n.
If the poly-V -belt is torn:
! do not continue driving. The engine could otherwise over-
heat.
X Consult aqualified specialist workshop.
If the poly-V-belt is OK:
X Visit aqualified specialist workshop. 4 Check
eng. oil
lev. when
next refu‐
elling The engine oil level has dropped to
acriticallevel.
Aw arning ton ealso sounds.
X Chec kthe oil level (Y page 260).
X If necessary, top up the engin eoil (Y page 261).
X Hav ethe engin echecked for leak sifthe engin eoil needs
topping up more often than usual. C There is only
asmall amount of fue linthe fuel tan k.
X Refuel at the nearest filling station. 8 Reserve
fue
llevel Th
ef uel level has fallen below the reserve range.
The fuel tank must be filled at least to the reserve fuel level
to prevent impairment to the running of the engine.
X Refuel at the nearest filling station. Display messages
223On-board computer and displays
BA 207 ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafaV ersion: 3.0.2.11
2010-01-26T13:03:22+01:0
0-Seite 223 Z

Displa
ymessages Possible causes/consequences and
M Solutions
P Se
lect
Par k( P) While the HOLD functio
norDISTRONIC PLUSisa ctive, you
have:
R opened the driver's door and releasedthe sea tbelt or
R switched off the engin eor
R opened the bonnet
At one ma yalso sound at regular intervals. The ton ebecomes
louder if you attempt to lock the vehicle.
You can notstart the engine.
X Shift the transmission to position P.
You can restart the engine. Auxiliary
battery malfunc‐
tion The auxiliary battery for the automatic transmission is no lon-
ger being charged.
X
Visit aqualified specialist workshop. N The boot lid is open.
X
Close the boot lid. M G
Risk of accident
The bonnet is open. Awarning ton ealso sounds.
X Pull ove rand sto pthe vehicle safel yassoonasp ossible,
paying attention to roa dand traffic conditions.
X Engag ethe parkin gbrake.
X Close th ebonnet.
If the active bonnet (pedestrian protection) has been trig-
gered:
X Reset the bonnet (Y page 258).
X Close the bonnet. Active
bonnet malfunc‐
tion See
Owner's
Manual The active bonnet (pedestrian protection) is not active due to
am
alfunction.
X Visit aqualified special istworkshop. C At least one door is open.
Awarning ton ealso sounds.
X Close all doors. Display messages
231On-boardcomputer and displays
BA 20 7ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafa Version:3.0.2.11
2010-01-26T13:03:22+01:00
-Seite 231 Z

Vehicl
eequipment
i Thismanua ldesc ribe sallthe standard
and optional equipment of your vehicle
which wa savailable at th etime of pur-
chase. Countr y-specif ic differences are
possible. Bear in mind tha tyour vehicle
ma ynot featur eall function sdescribed
here. Engine comp
artment Bonnet
Active bonnet (pedestrian protection) Operating principle
i
The activ ebonnet is only available in cer-
tain coun tries.
The activ ebonnet can reduce the risk of injury
to pedestrian sincertain acciden tsituations.
Raising the bonnet increases the clearanc eto
har dcomponents, such as the engine. If active bonnet
:has been triggered, it is
raised at the back by about 50 mm .Then,
lids ;no longer rest on housings =.
You can reset atriggere dbonnet yourself.
! Do not tr ytopressdown the raised bon-
net at the back .Otherwi se,the bonnet
could be damaged.
If the act iveb onnet is triggered, yo ucan also
continue driving and have it reset at aquali-
fied specialis tworkshop. If you pull the bon- net release lever, you must reset the bonnet
befor edriving on. G
Ris
kofa ccident
If you pull the bonnet release lever and then
neglect to reset the bonnet, it will not lock at
the front when closed. The bonnet can then
open when the vehicle is in motion and
obscure your field of vision. If you pull the
bonnet release lever, you must reset the bon-
net before driving on.
Resetting G
Risk of injury
There is arisk of injur yifthe bonnet is open,
even if the engin eisnot running.
Som eengine compone ntsc an become very
hot.
To avoid the risk of burns, only touch those
components described in the Owner's Manual
and observe the relevant safety notes.
X Open the bonnet (Y page 259). Coupé (example)
X
Lift up the bonnet in centre Awith both
hands until the two lids of bonnet lifter ;
no longer move.
If you push the lids back, you will notice a
resistance.
X Releas ebonnet :.
X Check whether the lids of bonnet lifter ;
ar er estin gont he housings =(arrow). 258
Engine compartmentMaintenance and care
BA 20
7ECE ÄJ 2010 /1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00 -Seite 258

X
The lids of bonnet lifter ; are resting
on the hous ings:close bon-
net :(Ypage 260).
or
X The lids of bonnet lifter ; are no
trest-
in gont he housings: first lift up bon-
net :on left-h and?and then on right-
hand side B.Lift up bonnet :until the lid
of bonnet lifter ;no longe rmoves.
The lids of bonnet lifter ;must rest on
housings =(arrow).
X Close bonnet :(Ypage 260).
If you can notc lose bonnet :or the L
symbol appears in the multi-function display,
repeat the steps. G
Risk of accident
If the bonnet can still not be engaged properly
or the Lsymbol appears in the multifunc-
tion display, do not continue driving. The bon-
net can then open when the vehicle is in
motion and obscure your field of vision. Con-
sult aqualified specialist workshop .Other-
wise ,you may cause an accident and injure
yourself and others.
Opening th ebonnet G
Risk of accident
Do not pull the release lever while the vehicle
is in motion .Ifyou do so, the bonne tmay open
up and block your view. G
Risk of injury
There is arisk of injur yifthe bonnet is open,
even if the engin eisnot running.
Som eengine compone ntsc an become very
hot.
To avoid the risk of burns, only touch those
components described in the Owner's Manual
and observe the relevant safety notes. G
Risk of injury
The radiator fan between the radiator and the
engine can start automatically, even if the key has been removed from the ignition lock. For
this reason, you must not reach into the fan
rotation area. You could otherwise be injured.
Vehicles with
apetrol engine: The elec-
tronic ignition system uses high voltage. For
this reason ,you must never touc hignition
system component s(ignition coil, ignition
cables, spark plug connectors or test socket)
while:
R the engine is running
R the engine is being started
R the ignition is switched on and the engine
is being cranked by hand
You could otherwise suffer an electric shock
and be seriously or even fatally injured.
Vehicles with adiesel engine: The elec-
tronic injection control uses high voltage. For
this reason ,you must never touc hinjection
system components while:
R the engi neis running
R the engin eisbeing started
R the ignition is switched on
You could otherwise suffer an electric shock
and be seriously or even fatally injured.
X Make sure that the windscreen wipers are
switched off. G
Risk of injury
The windscreen wipers and wiper linkage
could be set in motion.
When the bonnet is open, you or others could
be injured by the wiper linkage.
Make sure that the windscreen wipers are
switched off .Remov ethe key or make sure
that no ignition position has been selected
with KEYLESS-GO. All indi cator lamps must be
off in the instrumen tpanel. Engine compartment
259Maintenance and care
BA 207 ECE ÄJ 2010/1a; 1; 2, en-GB
mkalafaV ersion: 3.0.2.11
2010-01-26T13:03:22+01:00
-Seite 259 Z

X
Pull release lever :on the bonnet.
The bonnet is released.
! Make sure that the windscreen wiper sare
not folde daway from the windscreen .Oth-
erwise, yo ucould damage the windscreen
wipers or the bonnet. X
Reach int othe gap, pull bonnet catch han-
dle ;up and lift the bonnet.
Closin gthe bonnet G
Ris
kofi njury
Make sure tha tnobody can becom etrapped
as you close th ebonnet.
X Lower the bonnet and let it fal lfrom a
height of approximatel y20c m.
X Check that th ebonnet has engaged prop-
erly.
If the bonnet can be raised slightly ,itisn ot
properly engaged. Open it again and close
it with alittle more force. Engine oil
Notes on the oil level Depending on drivin
gstyle, the vehicle con-
sumes amaximum of 0.8 loil per 100 0km.
Th eo il consumption may be higher than this
when the vehicle is new or if you frequently
drive at high engine speeds.
When checking the oil level:
R park the vehicle on alevel surface.
R the engine should be switched off for at
least fiv eminutes if the engine is at normal
operating temperature.
R the engine should be switched off for at
least thirt yminutes if the engine is not at
normal operating temperature, e.g. if the
engine was only started briefly.
Checking the oil level using the oil dip-
stick Depending on the engine, the oil dipstick may
be installed at
adifferent location. E3
50 (example)
X Pull oi ldipstick :out of the oil dipstick
tube.
X Wipe off oil dipstick :.
X Slowly insert oil dipstick :into the oil dip-
stick tube to the stop, and take it out again.
The oil level is correc tifthe level is between
MIN mark =and MAX mark ;.
X Top up the oil if necessary. 260
Engine compartmentMaintenance and care
BA 20
7ECE ÄJ 2010 /1a;1;2,e n-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00-Seite 260

After an accident
Problem Possible causes/consequences and
M Solutions
Fue
lisl eaking from the
vehicle. G
Ris
kofe xplosion or fire
The fuel line or the fuel tan kisf aulty.
X Immediately turn the key to position 0(Ypage 135)in the ignition
lock and remove it.
X Do not restart the engine under any circumstances.
X Consult aqualified special istworkshop. You are unable to
determine the exten
tof
the damag e. X
Consult aqualified specialis tworkshop. You can
notd etect any
damage. X
Start the engine as normal. The active bonnet func-
tion (pedestrian protec-
tion) has been trig-
gered. Your vehicle has been involved in
afrontal collision.
X Rese tthe triggered activ ebonnet (pedestrian protection)
(Y page 258). The NECK
-PRO head
restraints on the driv-
er's and front-
passenger seats have
been triggered. Your vehicle has been involved in
arear-end collision.
X Reset the triggered NECK-PRO head restraint s(Ypage 40). Where will
Ifind...? Wa
rning triangle
Removing the warning triangle X
Open the boot lid. Coupé (example)
X
Open the warning triangle holder and
remove warning triangle :. Where will
Ifind...?
273Breakdown assistance
BA 207ECE ÄJ 2010 /1a; 1; 2, en-GB
mkalafa Version: 3.0.2.11 2010-01-26T13:03:22+01:00 -Seite 273 Z