2010 MAZDA MODEL MAZDASPEED 3 headlight bulb

Black plate (415,1)
2. Slide the unit as shown in the figure to
remove it.
3. Detach the electrical connector from
the unit by pulling it to the rear.
4. Install the new side turn signal unit in
the reverse order of removal.
Brake lights/Taillights (Rear side
marker lights)
With LED bulb
Due to the complexity and difficulty of
the procedure, the LED bulbs should be
replaced by an Authorized Mazda Dealer.
NOTE
LED bulb replacement is not possible. The
rear combination component must be replaced.
With Non-LED bulb
(4 Door)
1. Pull the center of each plastic retainer
and remove the retainers and the trunk
end trim.
InstallationRemoval
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.
(5 Door)
1. Make sure the ignition is switched off,
and the headlight switch is off.
Maintenance and Care
Owner Maintenance
8-45
Mazda3_8AR3-EA-09E_Edition2 Page415
Monday, June 1 2009 1:19 PM
Form No.8AR3-EA-09E

Black plate (417,1)
2. Remove the cover.
Left side
Right side
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.
Reverse lights
(4 Door)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the center of each plastic retainer
and remove the retainers and the trunk
end trim.
InstallationRemoval
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.
(5 Door)
1. Make sure the ignition is switched off,
and the headlight switch is off.
Maintenance and Care
Owner Maintenance
8-47
Mazda3_8AR3-EA-09E_Edition2 Page417
Monday, June 1 2009 1:19 PM
Form No.8AR3-EA-09E

Black plate (418,1)
2. Remove the cover.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.
High-mount brake light
(4 Door)
1. Make sure the ignition is switched off,
and the headlight switch is off.2. Pull the center of each plastic retainer
and remove the retainers and the trunk
end trim.
InstallationRemoval
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.
(5 Door)
With LED bulb
Due to the complexity and difficulty of
the procedure, the LED bulbs should be
replaced by an Authorized Mazda Dealer.
NOTE
LED bulb replacement is not possible. The
rear combination component must be replaced.
8-48
Maintenance and Care
Owner Maintenance
Mazda3_8AR3-EA-09E_Edition2 Page418
Monday, June 1 2009 1:19 PM
Form No.8AR3-EA-09E

Black plate (419,1)
With Non-LED bulb
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the liftgate upper trim.
3. Disconnect the electrical connector
from the bulb by pressing the tab on
the connector with your finger and
pulling the connector sideward to the
left.
4. Turn the socket and bulb assembly
counterclockwise and remove it.5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse order
of removal.
License plate lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the lens,
and then remove the lens by carefully
prying on the edge of the lens with a
flathead screwdriver.
Maintenance and Care
Owner Maintenance
8-49
Mazda3_8AR3-EA-09E_Edition2 Page419
Monday, June 1 2009 1:19 PM
Form No.8AR3-EA-09E

Black plate (488,1)
qLight Bulbs
Exterior light
Light bulbCategory
Wattage ECE R (SAE)
HeadlightsHalogenHigh beam 60 HB3 (#9005)
Low beam 55 H11 (H11)
Xenon fusion bulb High/Low beam 35 D2S (D2S)
Daytime running lights (Canada)
í35 H8 (H8)
Front turn signal
lights/Front
side-marker
lights/Parking
lightsHalogen/Xenon fusion bulb
(With daytime running lights)
27/8―(#7444NA)
Xenon fusion bulb
(Without daytime
running lights)Front turn signal
lights/Front side-marker
lights
Parking lights 5 W5W (4CP)
Fog lights
íExcept 2.3-liter turbocharged engine 51 HB4 (#9006)
2.3-liter turbocharged engine 55 H11 (H11)
Side turn signal
lightsBulb type
*15 WY5W (―)
LED type (Integrated with outside mirror) LED*2―(―)
High-mount brake
light4 Door 21 W21W (1120)
5 DoorBulb type 18 W16W (#921)
LED type LED
*2―(―)
Rear turn signal lights 21 WY21W (32CP)
Brake
lights/TaillightsBulb type 21/5 W21/5W (#7443)
LED type LED
*2―(―)
Reverse lights 21 W21W (#7440)
License plate lights 5 W5W (―)
Rear side-marker lights
íLED*2―(―)
*1 Bulb replacement is not possible because it is built into the unit. Replace the unit.
*2 LED is the abbreviation for Light Emitting Diode.
Interior light
Light bulbCategory
Wattage ECE R
Trunk light (4 Door) 3―
Luggage compartment light (5 Door) 5―
Overhead light/Map lights (Front) 8―
Overhead light (Rear) 10―
Vanity mirror lights
í2―
10-8íSome models.
Specifications
Mazda3_8AR3-EA-09E_Edition2 Page488
Monday, June 1 2009 1:19 PM
Form No.8AR3-EA-09E