2010 Lancia Musa engine

20
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
IGNITION SWITCH
The key can be turned to 3 different
positions:
❒STOP: engine off, key extractable,
steering locked. Some electric de-
vices (e.g. sound system, central
door locking system, etc.) may
work.
❒MAR: driving position. All electric
devices may work.
❒AV V: engine starting (unstable po-
sition).
The ignition switch is fitted with a
safety system that, in the event the en-
gine is not started, turns back the ig-
nition key to STOPbefore repeating
the starting operation.
Under no circumstances
should aftermarket opera-
tions involving steering system or
steering column modifications (e.g.:
installation of alarm) be carried
out that could badly affect perfor-
mance and safety. This also causes
the warranty to become null and
void and results in vehicle non-
compliance with type-approval re-
quirements.
WARNING
fig. 19L0D0021m
If the ignition device is
tampered with (e.g.: at-
tempted theft), have it checked over
by a Lancia Dealership as soon as
possible.
WARNING
Always remove the key
when you leave your car to
prevent someone from accidentally
operating the controls. Remember
to apply the handbrake. Engage
first gear if the car is parked up-
hill or reverse if the car is parked
downhill. Never leave children un-
attended in the car.
WARNING
STEERING LOCK
Engagement
When the key is in position STOP, re-
move the key and turn the steering
wheel until it is locked.
Switching off
Rock the steering wheel slightly as you
turn the ignition key to MAR.
Never extract the key while
the vehicle is moving. The
steering wheel would be locked as
soon as the steering wheel is turned.
This also applies to when the car is
towed.
WARNING

21
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
INSTRUMENTS
SPEEDOMETER Fig. 20
This indicates the vehicle speed.
REV COUNTER Fig. 21
This indicates the engine revolution
per minute.
IMPORTANT The electronic injection
control system gradually shuts off the
flow of fuel when the engine is ‘over-
revving’ resulting in a gradual loss of
engine power.
When the engine is idling, the rev
counter may indicate a gradual or
sudden increase of the speed.
This is normal and does not indicate
a fault. It may be caused, for exam-
ple, by the operation of the climate
control system or fan. In these case, a
slow change in engine speed is used to
protect the battery charge.The reserve warning light Aturns on
to indicate that approximately
6 litres of fuel are left in the tank.
Do not travel with the tank nearly
empty: lack of fuel supply could dam-
age the catalyser. FUEL LEVEL GAUGE Fig. 22
The instrument shows the litres of fuel
contained in the tank (see the “Refu-
elling” paragraph for a description).
fig. 20L0D0241mfig. 22L0D0023m
fig. 21L0D0242mfig. 23L0D0024m

22
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
MULTIFUNCTIONAL
DISPLAY
(on two-line modal
panel)
The car can be equipped with the mul-
tifunction display for showing useful in-
formation necessary when driving ac-
cording to settings. ENGINE
COOLANT TEMPERATURE
GAUGE fig. 23
Warning light Aindicates overheating
of the engine coolant. In this case, stop
the engine and contact a Lancia Deal-
ership. This shows the temperature of
the engine coolant fluid and starts
working when the fluid temperature ex-
ceeds approx. 50°C. In normal condi-
tions, the needle may point to different
positions according to use and the en-
gine cooling system management.
IMPORTANT The needle will point to
the lowest value of the scale (low tem-
perature) and warning light Awill
light up to indicate a fault in the sys-
tem. Go to a Lancia Dealership to
have the system checked.
If the needle reaches the red
area, stop the engine imme-
diately and contact a Lan-
cia Dealership.
fig. 24L0D0497m
“STANDARD” SCREEN fig. 24
The standard screen shows the fol-
lowing information:
AOdometer (kilometres or miles
travelled)
BClock (always displayed, even
with key extracted and front doors
closed)
CHeadlight adjustment (only with
dipped beam headlights on)
DGear shift suggestion.
NOTE When opening one of the front
doors, the display will turn on and
show for a few seconds the clock and
the kilometres or miles covered.

33
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Adjusting the button volume
(Button Vol.)
This function is used to set the volume
of the roger-beep accompanying the
activation of buttons MODE,+e–
through 8 levels.
To set the desired volume, proceed as
follows:
– briefly press button MODE: the pre-
viously set volume “level” starts flash-
ing on the display;
– press button +or–to set;
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen without storing the set-
tings.
S.B.R. buzzer reactivation
(Belt Buzzer)
(for versions/markets, where provided)
This function can be only displayed
after Lancia Dealership has deacti-
vated the S.B.R. system (see para-
graph “S.B.R. system” in section
“Safety devices”).The indications will appear more fre-
quently where there are 200 km left.
For 1.3 Multijet versions, refer to the
“Service Schedule” in the “Mainte-
nance and care” chapter for replacing
the air cleaner, the engine oil and the
engine oil filter. The indication will ap-
pear in kilometres or miles according
to the settings. When the next sched-
uled service operation is approaching,
the message “Service” will appear on
the display followed by the number of
kilometres or miles left when the key is
turned to MAR. The “Service Sched-
ule” information is provided with kilo-
metres (km)/miles (mi) or days (dd),
according to the deadline which ap-
pears first. Go to a Lancia Dealership
where the “Scheduled Service” opera-
tions will be performed and the mes-
sage will be reset. Scheduled Servicing (Service)
This function may be used to display
information connected to proper car
servicing in terms of kilometres or
days.
This information can be consulted as
follows:
–briefly press button MODE: service
in km or mi, according to previous
setting, will be displayed (see para-
graph “Units”);
– press button +or–to set deadline
in days;
– briefly press button MODEto go
back to the menu screen or hold the
button pressed to go back to the stan-
dard screen.
NOTE The “Service Schedule” re-
quires the car to be services every
20,000 km (or equivalent distance in
miles) or once a year. This message
will appear automatically with key at
MARafter 2,000 km (or equivalent
distance in miles) or 30 before the
deadline and will appear every 200
km (or equivalent distance in miles)
or 3 days.

36
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
New mission
The new mission begins after:
– “manual” resetting by the user, by
pressing the relevant button;
– “automatic” resetting, when the
“Trip distance” reaches 9999.9 km or
when the “Travel time” reaches 99.59
(99 hours and 59 minutes);
– after disconnecting/reconnecting the
battery.
IMPORTANT “General Trip” resets
will reset “Trip B” at the same time,
while resetting “Trip B” will only re-
set the values of the trip B function. Average speed
This shows the car average speed as a
function of the overall time elapsed
since the start of the new mission.
Journey time
This value shows the time elapsed
since the start of the new mission.
IMPORTANT If information is not
available, the message “----” will ap-
pear instead of the Trip Computer
values. Displaying of the values will
be resumed when normal operation is
restored without resetting the values
displayed before the problem nor
starting a new mission.
TRIP button fig. 29
ButtonTRIPlocated on the top of the
right steering column stalk is used
(with ignition key at MAR) to display
and reset the previously described val-
ues to start a new mission:
– short push to display the different
values
– long push to reset and then start a
new mission. Values displayed
Range
This indicates the indicative distance
which may be travelled with the fuel in
the tank assuming that driving condi-
tions do not change. The display will
show the reading “----“ when the fol-
lowing events take place:
– range lower than 50 km (or 30
miles) or fuel level less than 4 litres in
the tank;
– car left parked with engine running
for a long time.
Distance travelled
This value shows the distance covered
from the start of the new mission.
Average consumption
This indicates the indicative average
consumption from the start of the new
mission.
Instantaneous fuel consumption
This indicates the fuel consumption.
The value is constantly updated. The
message “----” will appear on the dis-
play if the car is parked with the en-
gine running.
fig. 29L0D0026m

45
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
ADJUSTING THE
STEERING WHEEL
The steering wheel can be adjusted in
heightA-fig. 52and in depth B.
To carry out the adjustment, proceed
as follows:
❒release the lever by pulling it to-
wards the steering wheel (position
2);
❒adjust the steering wheel as re-
quired;
❒release the lever by pushing it for-
wards (position 1);
Saddle-shaped rear head
restraints optimise visibil-
ity and must always be raised it
when an occupant is present.
WARNING
fig. 52L0D0382m
Any adjustment of the
steering wheel position
must be carried out only with the
car stationary and the engine
turned off.
WARNING
It is absolutely forbidden
to carry out whatever af-
ter-market operation involving
steering system or steering column
modifications (e.g.: installation of
anti-theft device) that could badly
affect performance and safety,
cause the lapse of warranty and
also result in non-compliance of
the car with homologation require-
ments.
WARNING
The head restraints must
be adjusted so that they
support your neck and not your
head. Only in this way may they
perform their protective action.
WARNING
To optimise head restraint
protective action, adjust
the seat back upright and keep
your head as close as possible to
the head restraint.
WARNING
To refit the head restraint,
arrange it the right way
and then proceed as for checking
that it is locked.
WARNING

60
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
IMPORTANT The fast demist/defrost
function will remain on for approxi-
mately 3 minutes, from when the en-
gine coolant reaches a temperature of
50°C (petrol versions) or 35°C (Mul-
tijet versions).
When this function is on, the LED of
the corresponding button switches on
and that of the rear window demister.
The message FULL AUTOgoes off on
the display.
You can only adjust the fan speed and
switch the rear window demister off
manually when this function is active.
To restore running operations before
this function was activated, press ei-
ther button F, air recirculation button
C, compressor button Bor button
AUTO NorH. Fast window
demisting/
defrosting
button F
Press this button: the
climate control system will automati-
cally switch on all the functions re-
quired for fast windscreen and front
side window demisting/defrosting,
that is:
❒climate control compressor on
when weather conditions are suit-
able;
❒air recycle off;
❒maximum air temperature HIon
both areas;
❒proper fan speed according to en-
gine coolant temperature to limit
the flow of not sufficiently warm air
to demist the windows into the pas-
senger compartment;
❒air flow to the windscreen and
front side windows vents;
❒the heated rear window on The switching off of the climate con-
trol compressor remains in storage
even when the engine has been
stopped.
To restore automatic compressor con-
trol, press
√again (in this case, the
system will only work as a heater) or
press AUTO.
When the compressor is off, if the ex-
ternal temperature is hotter than the
set temperature and the system can-
not satisfy the request, the digits of
the set temperature will blink for a
few seconds and the message AUTO
will go out.
With climate control compressor off,
the fan speed can be set to zero man-
ually (no bar shown).
With the compressor on and the en-
gine started, the fan speed may be re-
duced to the minimum setting (only
one bar shown).

61
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Switching the
system off E
Press Eto switch the
climate control system
off. The display will
go out as a conse-
quence.
The following climate control condi-
tions will be established when the sys-
tem is off:
❒LEDs off;
❒set temperature not shown;
❒air recirculation on, passenger com-
partment isolated from the outside;
❒air conditioner compressor off;
❒fan off.The rear window heater can be turned
on and off manually by pressing G
when the system is off.
IMPORTANT The climate control sys-
tem control unit stores the settings be-
fore the system is turned off and rep-
resents the same settings when it
turned back on by pressing any but-
ton (except for the heated rear win-
dow). If the function corresponding to
the pressed button was off, it will be
turned on; if it was on, it will be kept
on.
Press AUTOto turn the climate con-
trol system in fully automatic mode. Rear window
heater and external
rearview mirror
heater on/off
button G
Press this button to turn the rear win-
dow demister/defroster on. The LED
in the button will light up when the
function is on.
The heater will go out automatically
after a certain time or by pressing the
button again. It will also go out when
the engine is stopped until it is started
again.
IMPORTANT Do not apply stickers
over the electric filaments on the in-
side of the rear window to prevent
damage and ensure perfect operation.