2010 Lancia Delta light

176IN AN EMERGENCY
STARTING THE ENGINE
Go to a Lancia Dealership immediately if instrument pan-
el warning light
Yremains on constantly.
JUMP STARTING fig. 1
If the battery is flat, the engine may be started using an
auxiliary battery with the same capacity or a little high-
er than the flat one.
Proceed as follows to start the car:
❍connect the positive terminals (+ sign near the termi-
nal) of the two batteries with a jump lead;
❍with a second lead, connect the negative terminal –
of the auxiliary battery to an earth point E
on the en-
gine or the gearbox of the car to be started;
❍start the engine;
❍when engine has started, remove the cables by revers-
ing the sequence described for connection.
fig. 1L0E0074m
Never use a quick battery charger for an
emergency start: this could damage the elec-
tronic systems and the engine fuel feed and
ignition control units.
This starting procedure must be carried out
by expert personnel as incorrect manoeuvres
can cause electrical discharges of consider-
able intensity. Furthermore, battery fluid is poiso-
nous and corrosive: avoid contact with your skin
and eyes. Keep naked flames away from the battery.
No smoking. Do not cause sparks.
175-214 Delta 4ed gb 24-02-2010 14:36 Pagina 176

IN AN EMERGENCY185
4
REPLACING A WHEEL
GENERAL INSTRUCTIONS
The vehicle can be provided with (if requested, for ver-
sions/markets, where provided) a small spare wheel.
Wheel changing and correct use of the jack and of the
small spare wheel call for some precautions as listed
below.
The small spare wheel (for versions/markets,
where provided) is specific for your car. Do
not use it on different models of car. Do not
use spare wheels from different models on your car.
The small spare wheel must only be used in an
emergency. Never use it for more than strictly nec-
essary and never exceed 80 km/h. On the small
spare wheel there is an orange label, summarizing
the main warnings regarding small spare wheel us-
age restrictions.
Never remove or cover the label. Never apply
any hub cap on the small spare wheel. The
label contains the following indications in
four languages: Warning! For temporary use only!
80 km/h max! Replace as soon as possible with a
standard service wheel. Never cover this indication.
If you choose to install wheels of a different type
(with alloy rims instead of steel ones) you must al-
so change all the wheel retaining bolts with others
of a suitable size.
Indicate that the car is stationary according
to the laws in force: hazard warning lights,
refracting warning triangle, etc. Passengers
should leave the car, particularly if it is very loaded
and wait for the wheel to be changed away from on-
coming traffic. In the event of a wheel change on a
slope or on unsurfaced roads, chock the wheels.
175-214 Delta 4ed gb 24-02-2010 14:36 Pagina 185

192IN AN EMERGENCY
After tyre replacement
❍stow the small spare wheel D-fig. 10 in the space pro-
vided in the luggage compartment;
❍fit the partially-opened jack in its box, forcing it light-
ly to prevent it from vibrating when travelling;
❍put the tools back into place in the container;
❍stow the container, complete with tools, into the spare
wheel and tighten the locking device B-fig. 10;
❍put back the luggage compartment mat into the prop-
er position.
IMPORTANT Do not use an inner tube with tubeless tyres.
Periodically check the inflation pressure of the tyres and
small spare wheel.CHANGING A BULB
GENERAL INSTRUCTIONS
❍Before changing a bulb check the contacts for oxida-
tion;
❍blown bulbs must be replaced with others of the same
type and power;
❍after replacing a headlight bulb, always check its align-
ment for safety reasons;
❍when a bulb is not working, check that the corre-
sponding fuse is intact before replacing it: refer to the
“Replacing fuses” paragraph in this chapter for fuse
location.
Modifications or repairs to the electrical sys-
tem that are not carried out properly or do
not take the system’s technical specifications
into account can cause malfunctions leading to the
risk of fire. If you choose to install wheels of a different
type (with alloy rims instead of the steel ones
or vice versa) you must change all the re-
taining bolts with others of a suitable size and use
a specific small spare wheel, with different speci-
fications. It is advisable to keep the replaced bolts
and small spare wheel, as they are necessary if in
future you decide to reinstall the original wheels.
175-214 Delta 4ed gb 24-02-2010 14:36 Pagina 192

IN AN EMERGENCY193
4
Halogen bulbs contain gas under pressure, if
they break, glass fragments may be dis-
persed.IMPORTANT A slight misting may appear on the inter-
nal surface of the headlight: this does not indicate a fault
and is caused by low temperature and the degree of hu-
midity in the air. Misting will rapidly disappear when the
headlights are switched on. The presence of drops inside
the headlights indicates water penetration. Contact a Lan-
cia Dealership.
IMPORTANT When the weather is cold or damp or after
hard rain or after washing, the area of headlamps or rear
lights, may steam up and/or form drops of condensation
on the inside. This is a natural phenomenon due to the dif-
ference in temperature and humidity between the inside
and the outside of the glass which does not indicate a fault
and does not compromise the normal operation of light-
ing devices. The mist disappears quickly turning the lights
on, starting from the centre of the diffuser, extending pro-
gressively towards the edges.
When handling halogen bulbs, only touch the
metal part. Touching the transparent part of
the bulb with your fingers may reduce the in-
tensity of the emitted light and even compromise the
life of the lamp. In the event of accidental contact,
wipe the bulb with a cloth moistened with alcohol
and leave it to dry.
Where possible, it is advisable to have bulbs
changed at a Lancia Dealership. The correct
operation and orientation of the external
lights is essential for safe driving. You may be li-
able to fines if this is not the case.
175-214 Delta 4ed gb 24-02-2010 14:36 Pagina 193

IN AN EMERGENCY195
4
LED
LED
D1S(*) / H7
H1(*) / H7
PY 24W
LED
WY5W
LED
LED
W5W
H11
W16W
W16W
5L/5K
12V 5W
12V 5W
W5W–
–
D
D
B
–
A
–
–
C
E
B
B
–
C
C
A–
–
55W
55W
24W
–
5W
–
–
5W
55W
16W
16W
–
5W
5W
5W
(*) Xenon gas discharge bulb
Bulb Type Power Ref. figure
Front side lights/Daylight lights
Rear side lights
Dipped beams
Main beams
Front direction indicators
Rear direction indicators
Side direction indicators
Brake light
3rd brake light
Number plate light
Fog lights
Rear fog lights
Reversing light
Front courtesy light (white LED’s)
Rear courtesy light
Glove compartment/luggage compartment
courtesy light
Door lights
175-214 Delta 4ed gb 24-02-2010 14:36 Pagina 195

196IN AN EMERGENCY
REPLACING EXTERIOR BULBS
FRONT LIGHT CLUSTERS fig. 15
These contain the bulbs for the dipped beams, main beams
and direction indicators. The bulbs are arranged as fol-
lows:
A. Main beam headlights;
B. Dipped beam headlights;
C. Direction indicators.DIPPED BEAM HEADLIGHTS
With incandescent bulbs
To change the bulb, proceed as follows:
❍remove the protective cover B-fig. 15;
❍release the bulb holder clip A-fig. 16;
❍disconnect the electrical connector B;
❍remove the bulb C and replace it;
❍fit the new bulb, ensuring that the outline of the met-
al part coincides with the grooves on the curve of the
headlight. Then reconnect the electrical connector B
and reattach the bulb holding clip A;
❍refit the protective cover A-fig. 15.
fig. 15L0E0154mfig. 16L0E0155m
175-214 Delta 4ed gb 24-02-2010 14:36 Pagina 196

IN AN EMERGENCY197
4
With gas discharge bulbs (Xenon)
(for versions/markets, where provided)
MAIN BEAM HEADLIGHTS
With incandescent bulbs
To change the bulb, proceed as follows:
❍remove the protective cover A-fig. 15;
❍release the bulb holder clip A-fig. 17;
❍disconnect the electrical connector B;
❍remove the bulb C and replace it;
❍fit the new bulb, ensuring that the outline of the met-
al part coincides with the grooves on the curve of the
headlight. Then reconnect the electrical connector B
and reattach the bulb holding clip A;
❍refit the protective cover B-fig. 15.
fig. 17L0E0156m
Due to the high power supply voltage, gas
discharge bulbs (Xenon) should only be re-
placed by specialised personnel: risk of death!
Contact a Lancia Dealership.
With gas discharge bulbs (Xenon)
(for versions/markets, where provided)
Due to the high power supply voltage, gas
discharge bulbs (Xenon) should only be re-
placed by specialised personnel: risk of death!
Contact a Lancia Dealership.
175-214 Delta 4ed gb 24-02-2010 14:36 Pagina 197

198IN AN EMERGENCY
SIDELIGHTS/DAYTIME LIGHTS
The direction indicators/daylight lights are LED-based.
Contact a Lancia dealership to have there lights replaced.
DIRECTION INDICATORS
Front indicators
To change the bulb, proceed as follows:
❍remove the protective cover C-fig. 15;
❍press down near the bulb holder locking tabs (shown
in fig. 18 by the arrows) and simultaneously pull the
unit;
❍remove the bulb A and replace it;
❍refit the protective cover C.Side indicators
To change the bulb, proceed as follows:
❍work on lens A-fig. 19 to compress catch B, then pull
the unit outwards;
❍turn the bulb holder C, anticlockwise, extract the press-
fitted bulb D and replace it;
❍refit the bulb holder C in the lens and turn it clock-
wise;
❍refit the unit making sure that internal catch B clips
into position.
fig. 18L0E0157mfig. 19L0E0158m
175-214 Delta 4ed gb 24-02-2010 14:36 Pagina 198