2010 JEEP GRAND CHEROKEE display

message will be displayed in the instrument
cluster, and the “Tire Pressure Monitoring
Telltale Light” will turn ON. After driving the
vehicle for up to 20 minutes above 15 mph
(25 km/h), the “Tire Pressure Monitoring
Telltale Light” will flash on and off for
75 seconds and then remain on solid. In
addition, a “SERVICE TPM SYSTEM” mes-
sage will be displayed. For each subsequent
ignition switch cycle, a chime will sound, a
“SERVICE TPM SYSTEM” message will be
displayed, and the “Tire Pressure Monitor-
ing Telltale Light” will flash on and off for
75 seconds and then remain on solid. Once
you repair or replace the original road tire,
and reinstall it on the vehicle in place of the
spare tire, the TPMS will update automati-
cally and the “Tire Pressure Monitoring Tell-
tale Light” will turn OFF, as long as no tire
pressure is below the low-pressure warning
limit in any of the four active road tires. The
vehicle may need to be driven for up to
20 minutes above 15 mph (24 km/h) in order
for the TPMS to receive this information.Premium System – If EquippedThe Tire Pressure Monitor System (TPMS) uses
wireless technology with wheel rim-mounted
electronic sensors to monitor tire pressure lev-
els. Sensors, mounted to each wheel as part of
the valve stem, transmit tire pressure readings
to the Receiver Module.
NOTE:
It is particularly important, for you to regu-
larly check the tire pressure in all of your
tires and to maintain the proper pressure.
The Tire Pressure Monitor System (TPMS) con-
sists of the following components:
•Receiver Module
• Four Tire Pressure Monitoring Sensors
• Tire Pressure Monitoring Telltale Light
• Various Tire Pressure Monitoring System
Messages, which display in the Electronic
Vehicle Information Center (EVIC), and a
graphic displaying tire pressures Tire Pressure Monitoring Low Pressure
Warnings
When one or more of the four active road tire
pressures are low, the “TPM Telltale Light” will
illuminate, an audible chime will sound, the
EVIC will display “Low Tire Pressure” message
for a minimum of five seconds, and a graphic
display of the pressure value(s) with the low
tire(s) “flashing.” Refer to “Electronic Vehicle
Information Center (EVIC)” in “Understanding
Your Instrument Panel” for further information.
NOTE:
Your system can be set to display pressure
units in PSI, kPa, or BAR.
237

Should a low tire condition occur on any of the
four active road tire(s), you should stop as soon
as possible, and inflate the low tire(s) that is
“flashing” on the graphic display to the vehi-
cle’s recommended cold tire pressure. The
system will automatically update, the graphic
display of the pressure value(s) will stop “flash-
ing,” and the Low Pressure text message(s) will
switch off once the updated tire pressure(s)
have been received. The vehicle may need to
be driven for up to 20 minutes above 15 mph
(24 km/h) to receive this information.
SERVICE TPM SYSTEM Warning
When a system fault is detected, the “TPM
Telltale Light” will flash on and off for 75 sec-
onds then remain on solid, and a chime will
sound. The EVIC will display a “SERVICE TPM
SYSTEM” message. This message is then fol-
lowed by a graphic display, with “- -“ in place of
the pressure value(s), indicating which Tire
Pressure Monitoring Sensor(s) is not being re-
ceived.
NOTE:
Your system can be set to display pressure
units in PSI, kPa, or BAR.If the ignition switch is cycled, this sequence
will repeat, providing the system fault still ex-
ists. If the system fault no longer exists, the
“TPM Telltale Light” will no longer be illumi-
nated, the “SERVICE TPM SYSTEM
message
will not be present, and a pressure value will be
displayed instead of dashes. A system fault
can occur by any of the following:
1. Jamming due to electronic devices or driv-
ing next to facilities emitting the same Radio
Frequencies as the TPM sensors.
2. Installing some form of aftermarket window
tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or
wheel housings.
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped with TPM
sensors.
The “TPM Telltale Light” will also flash on and
off for 75 seconds and then remain on, and the
EVIC will display a
SERVICE TPM SYSTEM 
message when a system fault is detected pos-
sibly related to an incorrect sensor location
fault. In this case, the SERVICE TPM SYSTEM 
message is then followed by a graphic display,
with pressure values still shown. This indicates
the pressure values are still being received
from the TPM Sensors. However, the system
still needs to be serviced as long as the SER-
VICE TPM SYSTEM message exists.
NOTE:
There is no tire pressure monitoring sensor
in the spare tire. The TPMS will not be able to
monitor the tire pressure. If you install the
spare tire in place of a road tire that has a
pressure below the low-pressure warning
limit, upon the next ignition switch cycle, a
chime will sound, the TPM Telltale Light 
238

will turn on, and the EVIC will still display a
Low Pressure message and a “flashing”
pressure value in the graphic display. After
driving the vehicle for up to 20 minutes
above 15 mph (24 km/h), theTPM Telltale
Light will flash on and off for 75 seconds
and then remain on, the EVIC will display a
“SERVICE TPM SYSTEM message and then
display dashes (- -) in place of the pressure
value. For each subsequent ignition switch
cycle, a chime will sound, the TPM Telltale
Light will flash on and off for 75 seconds
and then remain on, the EVIC will display a
 SERVICE TPM SYSTEM message and then
display dashes (- -) in place of the pressure
value. Once you repair or replace the origi-
nal road tire, and reinstall it on the vehicle in
place of the spare tire, the TPMS will update
automatically.
In addition, the graphic in the EVIC will display
a new pressure value instead of dashes (- -), as
long as no tire pressure is below the low-
pressure warning limit in any of the four active
road tires. The vehicle may need to be driven
for up to 20 minutes above 15 mph (24 km/h) in
order for the TPMS to receive this information.TPMS DeactivationThe TPMS can be deactivated if replacing all
four wheel and tire assemblies (road tires) with
wheel and tire assemblies that do not have
TPMS Sensors, such as when installing winter
wheel and tire assemblies on your vehicle To
deactivate the TPMS, first, replace all four
wheel and tire assemblies (road tires) with tires
not equipped with Tire Pressure Monitoring
(TPM) Sensors. Then, drive the vehicle for
20 minutes above 24 km/h (15 mph). The TPMS
will chime, the TPM Telltale Light will flash on
and off for 75 seconds and then remain on and
the Electronic Vehicle Information Center
(EVIC) will display the “SERVICE TPM SYSTEM”
message and then display dashes (--) in place
of the pressure values. Beginning with the next
ignition switch cycle, the TPMS will no longer
chime or display the “SERVICE TPM SYSTEM”
message in the EVIC but dashes (--) will remain
in place of the pressure values.
To reactivate the TPMS, replace all four wheel
and tire assemblies (road tires) with tires
equipped with TPM sensors. Then, drive the
vehicle for up to 20 minutes above 24 km/h
(15 mph). The TPMS will chime, the TPM Telltale Light
will flash on and off for 75 sec-
onds and then turn off, and the Electronic
Vehicle Information Center (EVIC) will display
the “SERVICE TPM SYSTEM” message as long
as no system fault exists. The EVIC will also
display pressure values in place of the dashes,
on the next ignition switch cycle the SERVICE
TPM SYSTEM message will no longer be dis-
played as long as no system fault exists.
General InformationTransmitter and receivers operate on a carrier
frequency of 433.92 MHz as required by EEC
regulations. These devices must be certified to
conform to specific regulations in each indi-
vidual country. Two sets of regulations are
involved: ETS (European Telecommunication
Standard) 300–220, which most countries use,
and German BZT federal regulation 225Z125,
which is based on ETC 300–220 but has addi-
tional unique requirements. Other defined re-
quirements are noted in ANNEX VI of COMMIS-
SION DIRECTIVE 95/56/EC. Operation is
subject to the following conditions:
• This device may not cause harmful interfer-
ence.
239

Loose Fuel Filler Cap Message
If the vehicle diagnostic system
determines that the fuel filler cap is
loose, improperly installed, or
damaged, a loose gascap indica-
tor will display in the EVIC telltale
display area. Refer to “Electronic
Vehicle Information Center (EVIC)” in “Under-
standing Your Instrument Panel” for further in-
formation. Tighten the fuel filler cap properly
and press the SELECT button to turn off the
message. If the problem continues, the mes-
sage will appear the next time the vehicle is
started.
TRAILER TOWINGIn this section you will find safety tips and
information on limits to the type of towing you
can reasonably do with your vehicle. Before
towing a trailer, carefully review this information
to tow your load as efficiently and safely as
possible.
To maintain warranty coverage, follow the re-
quirements and recommendations in this
manual concerning vehicles used for trailer
towing.
Common Towing DefinitionsThe following trailer towing related definitions
will assist you in understanding the following
information.
Gross Vehicle Weight Rating (GVWR)
The GVWR is the total allowable weight of your
vehicle. This includes driver, passengers,
cargo and trailer tongue weight. The total load
must be limited so that you do not exceed the
GVWR.
Gross Trailer Weight (GTW)
The GTW is the weight of the trailer plus the
weight of all cargo, consumables and equip-
ment (permanent or temporary) loaded in or on
the trailer in its loaded and ready for operation 
condition.
The recommended way to measure GTW is to
put your fully loaded trailer on a vehicle scale.
The entire weight of the trailer must be sup-
ported by the scale.
Gross Combination Weight Rating (GCWR)
The GCWR is the total permissible weight of
your vehicle and trailer when weighed in com-
bination. NOTE:
The GCWR rating includes a 150 lbs (68 kg)
allowance for the presence of a driver.
Gross Axle Weight Rating (GAWR)
The GAWR is the maximum capacity of the front
and rear axles. Distribute the load over the front
and rear axles evenly. Make sure that you do
not exceed either front or rear GAWR.
WARNING!
It is important that you do not exceed the
maximum front or rear GAWR. A dangerous
driving condition can result if either rating is
exceeded. You could lose control of the ve-
hicle and have an accident.
Trailer Tongue Weight (TW)
The TW is the downward force exerted on the
hitch ball by the trailer. In most cases it should
not be more than 5% of the trailer load. You
must consider this as part of the load on your
vehicle.
244

2. Turn OFF the ignition.
3. For vehicles with Keyless Enter-N-Go, re-
move the Keyless Enter-N-Go button and use
the key fob to complete this procedure. Refer to
“Starting Procedures/Keyless Enter-N-Go” in
“Starting and Operating” for further information.
4. Turn the ignition switch to the ON/RUN po-
sition, but do not start the engine.
5. Press and hold the brake pedal.
6. Shift the transmission into NEUTRAL.
7. Using the point of a ballpoint pen or similar
object, press and hold the recessed transfer
case N (Neutral) button (located by the selector
switch) for four seconds, until the light behind
the N symbol starts to blink, indicating shift in
progress. The light will stop blinking (stay on
solid) when the shift to N (Neutral) is complete.
A “FOUR WHEEL DRIVE SYSTEM IN NEU-
TRAL” message will display on the EVIC (Elec-
tronic Vehicle Information Center). Refer to
“Electronic Vehicle Information Center (EVIC)”
in “Understanding Your Instrument Panel” for
further information.8. Start the engine.
9. Shift the transmission into REVERSE.
10. Release the brake pedal for five seconds
and ensure that there is no vehicle movement.
11. Turn OFF the engine and leave the ignition
switch in the unlocked OFF position.
12. Firmly apply the parking brake.
13. Shift the transmission into PARK.CAUTION!
Damage to the transmission may occur if the
transmission is shifted into PARK with the
transfer case in NEUTRAL (N) and the engine
running. With the transfer case in NEUTRAL
(N) ensure that the engine is off prior to
shifting the transmission into PARK.
14. Attach the vehicle to the tow vehicle using
a suitable tow bar.
15. Release the parking brake.
16. Disconnect the negative battery cable, and
secure it away from the negative battery post.
NOTE:
• Steps 1 through 6 are requirements that
must be met prior to pressing the NEU-
TRAL (N) button, and must continue to be
met until the four seconds elapse and the
shift has been completed. If any of these
requirements are not met prior to press-
ing the NEUTRAL (N) button or are no
longer met during the four second timer,
then the NEUTRAL (N) indicator light will
Neutral Switch
253

flash continuously until all requirements
are met or until the NEUTRAL (N) button is
released.
• The ignition switch must be in the ON/
RUN position for a shift to take place and
for the position indicator lights to be op-
erable. If the ignition switch is not in the
ON/RUN position, the shift will not take
place and no position indicator lights will
be on or flashing.
• A flashing NEUTRAL (N) position indica-
tor light indicates that shift requirements
have not been met.
Shifting Out Of NEUTRAL (N)
Use the following procedure to prepare your
vehicle for normal usage.
1. Bring the vehicle to a complete stop, leaving
it connected to the tow vehicle.
2. Firmly apply the parking brake.
3. Reconnect the negative battery cable. 4. Turn the key fob to the LOCK/OFF position (if
it has been moved or the engine has been
started).
5. Turn the key fob to the ON/RUN position, but
do not start the engine.
6. Press and hold the brake pedal.
7. Shift the transmission into NEUTRAL.
8. Using the point of a ballpoint pen or similar
object, press and hold the recessed transfer
case N (Neutral) button (located by the selector
switch) for four seconds, until the light behind
the N symbol starts to blink, indicating shift in
progress. The light will stop blinking (go out)
when shift is complete. The “FOUR WHEEL
DRIVE SYSTEM IN NEUTRAL” message will no
longer be displayed on the EVIC (Electronic
Vehicle Information Center). Refer to “Elec-
tronic Vehicle Information Center (EVIC)” in
“Understanding Your Instrument Panel” for fur-
ther information.
NOTE:
When shifting out of transfer case NEUTRAL
(N), turning the engine OFF may be required
to avoid gear clash.
Neutral Switch
254

ONBOARD DIAGNOSTIC SYSTEM –
OBD II
Your vehicle is equipped with a sophisticated
onboard diagnostic system called OBD II. This
system monitors the performance of the emis-
sions, engine, and automatic transmission con-
trol systems. When these systems are operat-
ing properly, your vehicle will provide excellent
performance and fuel economy, as well as
engine emissions well within current govern-
ment regulations.
If any of these systems require service, the
OBD II system will turn on the “Malfunction
Indicator Light” (MIL). It will also store diagnos-
tic codes and other information to assist your
service technician in making repairs. Although
your vehicle will usually be drivable and not
need towing, see your authorized dealer for
service as soon as possible.
CAUTION!
•Prolonged driving with the MIL on could
cause further damage to the emission con-
trol system. It could also affect fuel
economy and drivability. The vehicle must
be serviced before any emissions tests can
be performed.
• If the MIL is flashing while the engine is
running, severe catalytic converter damage
and power loss will soon occur. Immediate
service is required.
Loose Fuel Filler Cap Message
If the vehicle diagnostic system
determines that the fuel filler cap is
loose, improperly installed, or
damaged, a loose gascap indica-
tor will display in the EVIC telltale
display area. Refer to “Electronic
Vehicle Information Center (EVIC)” in “Under-
standing Your Instrument Panel” for further in-
formation. Tighten the fuel filler cap properly
and press the SELECT button to turn off the message. If the problem continues, the mes-
sage will appear the next time the vehicle is
started.
A loose, improperly installed, or damaged fuel
filler cap may also turn on the Malfunction
Indicator Light (MIL).
REPLACEMENT PARTSUse of genuine MOPAR
parts for normal/
scheduled maintenance and repairs is highly
recommended to ensure the designed perfor-
mance. Damage or failures caused by the use
of non-MOPAR parts for maintenance and
repairs will not be covered by the manufactur-
er’s warranty.
MAINTENANCE PROCEDURESThe pages that follow contain the required
maintenance services determined by the engi-
neers who designed your vehicle.
Besides those maintenance items specified in
the fixed maintenance schedule, there are
other components which may require servicing
or replacement in the future.
273

MAINTENANCE SCHEDULE
Maintenance Schedule – Gasoline
Engine
The oil change indicator system will remind you
that it is time to take your vehicle in for sched-
uled maintenance.
On Electronic Vehicle Information Center
(EVIC) equipped vehicles “Oil Change Re-
quired” will be displayed in the EVIC and a
single chime will sound, indicating that an oil
change is necessary.
The oil change indicator message will illumi-
nate approximately 7,000 miles (11 200 km)
after the most recent oil change was per-
formed. Have your vehicle serviced as soon as
possible, within 500 miles (800 km).
NOTE:
•The oil change indicator message will not
monitor the time since the last oil change.
Change your vehicles oil if it has been
6 months since your last oil change even
if the oil change indicator message is
NOT illuminated. •
Change your engine oil more often if you
drive your vehicle off-road for an ex-
tended period of time.
• Under no circumstances should oil
change intervals exceed 7,500 miles
(12 000 km) or 6 months, whichever
comes first.
Your authorized dealer will reset the oil change
indicator message after completing the sched-
uled oil change. If this scheduled oil change is
performed by someone other than your autho-
rized dealer the message can be reset by
referring to the steps described under ”Elec-
tronic Vehicle Information Center” in “Under-
standing Your Instrument Panel” for further in-
formation.
At Each Stop for Fuel
• Check the engine oil level about 5 minutes
after a fully warmed engine is shut off.
Checking the oil level while the vehicle is on
level ground will improve the accuracy of the
oil level reading. Add oil only when the level
is at or below the ADD or MIN mark.
• Check the windshield washer solvent and
add if required. Once a Month
•
Check tire pressure and look for unusual
wear or damage.
• Inspect the battery and clean and tighten the
terminals as required.
• Check the fluid levels of the coolant reser-
voir, brake master cylinder, power steering
and transmission (5.7L only) and add as
needed.
• Check all lights and other electrical items for
correct operation.
At Each Oil Change
• Change the engine oil filter.
• Inspect the brake hoses and lines.
CAUTION!
Failure to perform the required maintenance
items may result in damage to the vehicle.
302