JACKING AND TIRE CHANGING
WARNING!
•Getting under a jacked-up vehicle is dan-
gerous. The vehicle could slip off the jack
and fall on you. You could be crushed.
Never get any part of your body under a
vehicle that is on a jack. If you need to get
under a raised vehicle, take it to a service
center where it can be raised on a lift.
• The jack is designed to be used as a tool
for changing tires only. The jack should not
be used to lift the vehicle for service pur-
poses. The vehicle should be jacked on a
firm, level surface only. Avoid ice or slippery
areas.
Jack LocationThe scissor-type jack and tire changing tools
are located in rear cargo area, below the load
floor.
Spare Tire StowageThe spare tire is stowed under the load floor in
the rear cargo area.
Preparations for Jacking
1. Park the vehicle on a firm, level surface.
Avoid ice or slippery surfaces.
WARNING!
Do not attempt to change a tire on the side of
the vehicle closest to moving traffic. Pull far
enough off the road to avoid being hit when
operating the jack or changing the wheel. 2. Turn on the Hazard Warning flasher.
3. Set the parking brake.
4. Place the shift lever into PARK.
5. Turn the ignition OFF.
6. Block both the front
and rear of the wheel
diagonally opposite of
the jacking position. For
example, if changing
the right front tire, block
the left rear wheel.
NOTE:
Passengers should not remain in the vehicle
when the vehicle is being jacked.
7. For vehicle equipped with Quadra-Lift refer
to “Quadra-Lift — If Equipped” in “Starting and
Operating” for further information on disabling
automatic leveling.
Jack Storage Location
259
Jacking Instructions
WARNING!
Carefully follow these tire changing warnings
to help prevent personal injury or damage to
your vehicle:
•Always park on a firm, level surface as far
from the edge of the roadway as possible
before raising the vehicle.
• Turn on the Hazard Warning flasher.
• Block the wheel diagonally opposite the
wheel to be raised.
• Set the parking brake firmly and set an
automatic transmission in PARK.
• Never start or run the engine with the
vehicle on a jack.
• Do not let anyone sit in the vehicle when it
is on a jack.
• Do not get under the vehicle when it is on a
jack.
• Only use the jack in the positions indicated
and for lifting this vehicle during a tire
change.
(Continued)
WARNING!(Continued)
• If working on or near a roadway, be ex-
tremely careful of motor traffic.
• To assure that spare tires, flat or inflated,
are securely stowed, spares must be
stowed with the valve stem facing the
ground.
1. Remove the spare tire, jack, and tools from
storage.
2. Loosen (but do not remove) the wheel lug
nuts by turning them to the left, one turn, while
the wheel is still on the ground.
3. Assemble the jack and jacking tools. 4. For a front tire, place the jack and protective
cap on the body flange just behind the front tire
(as indicated by the triangular lift point symbol
on the sill molding).
Do not raise the vehicle
until you are sure the jack is fully engaged.
Jack Warning Label
Jack and Tool Assembly
260
5. For a rear tire, place the jack and protective
cap in the slot on the rear tie-down bracket, just
forward of the rear tire (as indicated by the
triangular lift point symbol on the sill molding).
Do not raise the vehicle until you are sure
the jack is fully engaged.6. Raise the vehicle by turning the jack screw
clockwise. Raise the vehicle only until the tire
just clears the surface and enough clearance is
obtained to install the spare tire. Minimum tire
lift provides maximum stability.
WARNING!
Raising the vehicle higher than necessary can
make the vehicle less stable. It could slip off
the jack and hurt someone near it. Raise the
vehicle only enough to remove the tire.7. Remove the lug nuts and wheel.
8. Position the spare wheel/tire on the vehicle
and install the lug nuts with the cone-shaped
end toward the wheel. Lightly tighten the nuts.
To avoid the risk of forcing the vehicle off the
jack, do not tighten the nuts fully until the
vehicle has been lowered.
9. Lower the vehicle by turning the jack screw
counterclockwise, and remove the jack and
wheel blocks.
10. Finish tightening the lug nuts. Push down
on the wrench while tightening for increased
leverage. Alternate nuts until each nut has
been tightened twice. The correct wheel nut
tightness is 95 ft lbs (130 N·m). If in doubt about
the correct tightness, have them checked with
a torque wrench by your authorized dealer or at
a service station.
11. Lower the jack to the fully closed position
and return it and the tools to the proper posi-
tions in the foam tray.
Front Jacking LocationRear Jacking Location
261
12. Securely store the road wheel and jack in
the cargo area.
13. Have the aluminum road wheel and tire
repaired as soon as possible and properly
secure the spare tire, jack and tool kit.
WARNING!
A loose tire or jack, thrown forward in a
collision or hard stop could endanger the
occupants of the vehicle. Always stow the jack
parts and the spare tire in the places provided.
JUMP-STARTINGIf your vehicle has a discharged battery it can
be jump-started using a set of jumper cables
and a battery in another vehicle or by using a
portable battery booster pack. Jump-starting
can be dangerous if done improperly so please
follow the procedures in this section carefully.
NOTE:
When using a portable battery booster pack
follow the manufacturer’s operating instruc-
tions and precautions.
CAUTION!
Do not use a portable battery booster pack or
any other booster source with a system volt-
age greater than 12 Volts or damage to the
battery, starter motor, alternator or electrical
system may occur.
WARNING!
Do not attempt jump-starting if the battery is
frozen. It could rupture or explode and cause
personal injury.
Preparations for Jump-StartThe battery in your vehicle is located under the
passenger’s front seat. There are remote loca-
tions located under the hood to assist in jump-
starting.
Stowed Spare
Remote Battery Posts
1 — Remote Positive(+) Post
(covered with protective cap)
2 — Remote Negative (-) Post
262
Once the engine is started, remove the jumper
cables in the reverse sequence:
6. Disconnect the negative(-)jumper cable
from the remote negative (-)post of the dis-
charged vehicle.
7. Disconnect the negative end (-)of the
jumper cable from the negative (-)post of the
booster battery.
8. Disconnect the opposite end of the positive
(+) jumper cable from the positive (+)post of
the booster battery.
9. Disconnect the positive (+)end of the
jumper cable from the remote positive (+)post
of the discharged vehicle.
10. Reinstall the protective cover over the re-
mote positive (+)battery post of the discharged
vehicle. If frequent jump-starting is required to start your
vehicle you should have the battery and charg-
ing system inspected at your authorized dealer.
CAUTION!
Accessories that can be plugged into the
vehicle power outlets draw power from the
vehicle’s battery, even when not in use (i.e.,
cellular phones, etc.). Eventually, if plugged in
long enough, the vehicle’s battery will dis-
charge sufficiently to degrade battery life
and/or prevent the engine from starting.
TOW EYESYour vehicle is equipped with tow eyes, which
are mounted in the front and the rear.
CAUTION!
Tow eyes are for emergency use only, to
rescue a vehicle stranded off road. Do not use
tow eyes for tow truck hookup or highway
towing. You could damage your vehicle. Tow
straps are recommended when towing the
vehicle; chains may cause vehicle damage.
WARNING!
Stand clear of vehicles when pulling with tow
eyes. Tow straps and chains may break, caus-
ing serious injury.
264
TOWING A DISABLED VEHICLEThis section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the transmission and drivetrain are operable,
disabled vehicles may also be towed as described under “Recreational Towing” in the “Starting and Operating” section.
Towing Condition Wheels OFF the Ground 4WD Models
Flat Tow NONE See instructions in “Recreational Towing” under “Starting and Operating”
•
Trans in PARK
• T/case in NEUTRAL
• To w i n forward direction
Wheel Lift or Dolly Tow Front
NOT ALLOWED
Rear NOT ALLOWED
Flatbed ALL BEST METHOD
Proper towing or lifting equipment is required to
prevent damage to your vehicle. Use only tow
bars and other equipment designed for the
purpose, following equipment manufacturer’s
instructions. Use of safety chains is mandatory.
Attach a tow bar or other towing device to main
structural members of the vehicle, not to
bumpers or associated brackets. State and
local laws applying to vehicles under tow must
be observed. If you must use the accessories (wipers, de-
frosters, etc.) while being towed, the ignition
must be in the ON/RUN position, not the ACC
position.
If the vehicle’s battery is discharged, see
Brake/Transmission Interlock Manual Override
(under Starting and Operating, Automatic
Transmission) for instructions on shifting the
automatic transmission out of the PARK posi-
tion for towing.
CAUTION!
•
Do not attempt to use sling type equipment
when towing. When securing the vehicle to
a flat bed truck, do not attach to front or rear
suspension components. Damage to your
vehicle may result from improper towing.
• If the vehicle being towed requires steering,
the ignition must be in the ON/RUN or ACC
position, not in the LOCK position.
265
Towing Without the Ignition Key FobSpecial care must be taken when the vehicle is
towed with the ignition in the LOCK position.
The only approved method of towing without
the ignition key is with a flatbed truck. Proper
towing equipment is necessary to prevent
damage to the vehicle.Four-Wheel Drive VehiclesThe manufacturer recommends towing with all
wheelsOFFthe ground. Acceptable methods
are to tow the vehicle on a flatbed or with one
end of vehicle raised and the opposite end on
a towing dolly.
If flatbed equipment is not available, and the
transfer case is operable, the vehicle may be
towed (in the forward direction, with ALL
wheels on the ground), IFthe transfer case is in
NEUTRAL and the transmission is in PARK.
Refer to “Recreational Towing” in “Starting and
Operating” for further information.CAUTION!
• Front or rear wheel lifts should not be used.
Internal damage to the transmission or
transfer case will occur if a front or rear
wheel lift is used when towing.
• Failure to follow these towing methods
could result in damage to the transmission
and/or transfer case. Such damage is not
covered by the New Vehicle Limited War-
ranty.
266
ONBOARD DIAGNOSTIC SYSTEM –
OBD II
Your vehicle is equipped with a sophisticated
onboard diagnostic system called OBD II. This
system monitors the performance of the emis-
sions, engine, and automatic transmission con-
trol systems. When these systems are operat-
ing properly, your vehicle will provide excellent
performance and fuel economy, as well as
engine emissions well within current govern-
ment regulations.
If any of these systems require service, the
OBD II system will turn on the “Malfunction
Indicator Light” (MIL). It will also store diagnos-
tic codes and other information to assist your
service technician in making repairs. Although
your vehicle will usually be drivable and not
need towing, see your authorized dealer for
service as soon as possible.
CAUTION!
•Prolonged driving with the MIL on could
cause further damage to the emission con-
trol system. It could also affect fuel
economy and drivability. The vehicle must
be serviced before any emissions tests can
be performed.
• If the MIL is flashing while the engine is
running, severe catalytic converter damage
and power loss will soon occur. Immediate
service is required.
Loose Fuel Filler Cap Message
If the vehicle diagnostic system
determines that the fuel filler cap is
loose, improperly installed, or
damaged, a loose gascap indica-
tor will display in the EVIC telltale
display area. Refer to “Electronic
Vehicle Information Center (EVIC)” in “Under-
standing Your Instrument Panel” for further in-
formation. Tighten the fuel filler cap properly
and press the SELECT button to turn off the message. If the problem continues, the mes-
sage will appear the next time the vehicle is
started.
A loose, improperly installed, or damaged fuel
filler cap may also turn on the Malfunction
Indicator Light (MIL).
REPLACEMENT PARTSUse of genuine MOPAR
parts for normal/
scheduled maintenance and repairs is highly
recommended to ensure the designed perfor-
mance. Damage or failures caused by the use
of non-MOPAR parts for maintenance and
repairs will not be covered by the manufactur-
er’s warranty.
MAINTENANCE PROCEDURESThe pages that follow contain the required
maintenance services determined by the engi-
neers who designed your vehicle.
Besides those maintenance items specified in
the fixed maintenance schedule, there are
other components which may require servicing
or replacement in the future.
273