2010 JEEP GRAND CHEROKEE light

message will be displayed in the instrument
cluster, and the “Tire Pressure Monitoring
Telltale Light” will turn ON. After driving the
vehicle for up to 20 minutes above 15 mph
(25 km/h), the “Tire Pressure Monitoring
Telltale Light” will flash on and off for
75 seconds and then remain on solid. In
addition, a “SERVICE TPM SYSTEM” mes-
sage will be displayed. For each subsequent
ignition switch cycle, a chime will sound, a
“SERVICE TPM SYSTEM” message will be
displayed, and the “Tire Pressure Monitor-
ing Telltale Light” will flash on and off for
75 seconds and then remain on solid. Once
you repair or replace the original road tire,
and reinstall it on the vehicle in place of the
spare tire, the TPMS will update automati-
cally and the “Tire Pressure Monitoring Tell-
tale Light” will turn OFF, as long as no tire
pressure is below the low-pressure warning
limit in any of the four active road tires. The
vehicle may need to be driven for up to
20 minutes above 15 mph (24 km/h) in order
for the TPMS to receive this information.Premium System – If EquippedThe Tire Pressure Monitor System (TPMS) uses
wireless technology with wheel rim-mounted
electronic sensors to monitor tire pressure lev-
els. Sensors, mounted to each wheel as part of
the valve stem, transmit tire pressure readings
to the Receiver Module.
NOTE:
It is particularly important, for you to regu-
larly check the tire pressure in all of your
tires and to maintain the proper pressure.
The Tire Pressure Monitor System (TPMS) con-
sists of the following components:
•Receiver Module
• Four Tire Pressure Monitoring Sensors
• Tire Pressure Monitoring Telltale Light
• Various Tire Pressure Monitoring System
Messages, which display in the Electronic
Vehicle Information Center (EVIC), and a
graphic displaying tire pressures Tire Pressure Monitoring Low Pressure
Warnings
When one or more of the four active road tire
pressures are low, the “TPM Telltale Light” will
illuminate, an audible chime will sound, the
EVIC will display “Low Tire Pressure” message
for a minimum of five seconds, and a graphic
display of the pressure value(s) with the low
tire(s) “flashing.” Refer to “Electronic Vehicle
Information Center (EVIC)” in “Understanding
Your Instrument Panel” for further information.
NOTE:
Your system can be set to display pressure
units in PSI, kPa, or BAR.
237

Should a low tire condition occur on any of the
four active road tire(s), you should stop as soon
as possible, and inflate the low tire(s) that is
“flashing” on the graphic display to the vehi-
cle’s recommended cold tire pressure. The
system will automatically update, the graphic
display of the pressure value(s) will stop “flash-
ing,” and the Low Pressure text message(s) will
switch off once the updated tire pressure(s)
have been received. The vehicle may need to
be driven for up to 20 minutes above 15 mph
(24 km/h) to receive this information.
SERVICE TPM SYSTEM Warning
When a system fault is detected, the “TPM
Telltale Light” will flash on and off for 75 sec-
onds then remain on solid, and a chime will
sound. The EVIC will display a “SERVICE TPM
SYSTEM” message. This message is then fol-
lowed by a graphic display, with “- -“ in place of
the pressure value(s), indicating which Tire
Pressure Monitoring Sensor(s) is not being re-
ceived.
NOTE:
Your system can be set to display pressure
units in PSI, kPa, or BAR.If the ignition switch is cycled, this sequence
will repeat, providing the system fault still ex-
ists. If the system fault no longer exists, the
“TPM Telltale Light” will no longer be illumi-
nated, the “SERVICE TPM SYSTEM
message
will not be present, and a pressure value will be
displayed instead of dashes. A system fault
can occur by any of the following:
1. Jamming due to electronic devices or driv-
ing next to facilities emitting the same Radio
Frequencies as the TPM sensors.
2. Installing some form of aftermarket window
tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or
wheel housings.
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped with TPM
sensors.
The “TPM Telltale Light” will also flash on and
off for 75 seconds and then remain on, and the
EVIC will display a
SERVICE TPM SYSTEM 
message when a system fault is detected pos-
sibly related to an incorrect sensor location
fault. In this case, the SERVICE TPM SYSTEM 
message is then followed by a graphic display,
with pressure values still shown. This indicates
the pressure values are still being received
from the TPM Sensors. However, the system
still needs to be serviced as long as the SER-
VICE TPM SYSTEM message exists.
NOTE:
There is no tire pressure monitoring sensor
in the spare tire. The TPMS will not be able to
monitor the tire pressure. If you install the
spare tire in place of a road tire that has a
pressure below the low-pressure warning
limit, upon the next ignition switch cycle, a
chime will sound, the TPM Telltale Light 
238

will turn on, and the EVIC will still display a
Low Pressure message and a “flashing”
pressure value in the graphic display. After
driving the vehicle for up to 20 minutes
above 15 mph (24 km/h), theTPM Telltale
Light will flash on and off for 75 seconds
and then remain on, the EVIC will display a
“SERVICE TPM SYSTEM message and then
display dashes (- -) in place of the pressure
value. For each subsequent ignition switch
cycle, a chime will sound, the TPM Telltale
Light will flash on and off for 75 seconds
and then remain on, the EVIC will display a
 SERVICE TPM SYSTEM message and then
display dashes (- -) in place of the pressure
value. Once you repair or replace the origi-
nal road tire, and reinstall it on the vehicle in
place of the spare tire, the TPMS will update
automatically.
In addition, the graphic in the EVIC will display
a new pressure value instead of dashes (- -), as
long as no tire pressure is below the low-
pressure warning limit in any of the four active
road tires. The vehicle may need to be driven
for up to 20 minutes above 15 mph (24 km/h) in
order for the TPMS to receive this information.TPMS DeactivationThe TPMS can be deactivated if replacing all
four wheel and tire assemblies (road tires) with
wheel and tire assemblies that do not have
TPMS Sensors, such as when installing winter
wheel and tire assemblies on your vehicle To
deactivate the TPMS, first, replace all four
wheel and tire assemblies (road tires) with tires
not equipped with Tire Pressure Monitoring
(TPM) Sensors. Then, drive the vehicle for
20 minutes above 24 km/h (15 mph). The TPMS
will chime, the TPM Telltale Light will flash on
and off for 75 seconds and then remain on and
the Electronic Vehicle Information Center
(EVIC) will display the “SERVICE TPM SYSTEM”
message and then display dashes (--) in place
of the pressure values. Beginning with the next
ignition switch cycle, the TPMS will no longer
chime or display the “SERVICE TPM SYSTEM”
message in the EVIC but dashes (--) will remain
in place of the pressure values.
To reactivate the TPMS, replace all four wheel
and tire assemblies (road tires) with tires
equipped with TPM sensors. Then, drive the
vehicle for up to 20 minutes above 24 km/h
(15 mph). The TPMS will chime, the TPM Telltale Light
will flash on and off for 75 sec-
onds and then turn off, and the Electronic
Vehicle Information Center (EVIC) will display
the “SERVICE TPM SYSTEM” message as long
as no system fault exists. The EVIC will also
display pressure values in place of the dashes,
on the next ignition switch cycle the SERVICE
TPM SYSTEM message will no longer be dis-
played as long as no system fault exists.
General InformationTransmitter and receivers operate on a carrier
frequency of 433.92 MHz as required by EEC
regulations. These devices must be certified to
conform to specific regulations in each indi-
vidual country. Two sets of regulations are
involved: ETS (European Telecommunication
Standard) 300–220, which most countries use,
and German BZT federal regulation 225Z125,
which is based on ETC 300–220 but has addi-
tional unique requirements. Other defined re-
quirements are noted in ANNEX VI of COMMIS-
SION DIRECTIVE 95/56/EC. Operation is
subject to the following conditions:
• This device may not cause harmful interfer-
ence.
239

•This device must accept any interference
received, including interference that may
cause undesired operation.
FUEL REQUIREMENTS —
GASOLINE ENGINE
3.6L Engine
These engines are designed to meet all emis-
sions regulations and provide excellent fuel
economy and performance when using high-
quality unleaded gasoline with a minimum re-
search octane rating of 91. The use of premium
gasoline is not recommended, as it will not
provide any benefit over regular gasoline in
these engines.
5.7L EngineTheses engines are designed to meet all emis-
sions regulations and provide satisfactory fuel
economy and performance when using high-
quality unleaded gasoline having an octane
range of 91 to 95. The manufacturer recom-
mends the use of 95 octane for optimum per-
formance. The use of premium gasoline is not
recommended, as it will not provide any benefit
over regular gasoline in these engines. Light spark knock at low engine speeds is not
harmful to your engine. However, continued
heavy spark knock at high speeds can cause
damage, and immediate service is required.
Poor quality gasoline can cause problems such
as hard starting, stalling, and hesitations. If you
experience these symptoms, try another brand
of gasoline before considering service for the
vehicle.
Over 40 auto manufacturers worldwide have
issued and endorsed consistent gasoline
specifications (the Worldwide Fuel Charter,
WWFC) which define fuel properties necessary
to deliver enhanced emissions, performance,
and durability for your vehicle. The manufac-
turer recommends the use of gasoline that
meets the WWFC specifications if they are
available.
Besides using unleaded gasoline with the
proper octane rating, gasolines that contain
detergents, corrosion and stability additives
are recommended. Using gasolines that have
these additives may help improve fuel
economy, reduce emissions, and maintain ve-
hicle performance.
Poor quality gasoline can cause problems such
as hard starting, stalling and stumble. If you
experience these problems, try another brand
of gasoline before considering service for the
vehicle.
Methanol
(Methyl or Wood Alcohol) is used in a variety of
concentrations when blended with unleaded
gasoline. You may find fuels containing 3% or
more Methanol along with other alcohols called
cosolvents. Problems that result from using
Methanol/gasoline or E85 Ethanol blends are
not the responsibility of the manufacturer. While
MTBE is an oxygenate made from Methanol, it
does not have the negative effects of Methanol.CAUTION!
Do not use gasolines containing Methanol or
E85 Ethanol. Use of these blends may result
in starting and driveability problems and may
damage critical fuel system components.
240

2. Open the fuel filler door, and remove the fuel
filler cap.
CAUTION!
•Damage to the fuel system or emission
control system could result from using an
improper fuel cap (gas cap). A poorly fitting
cap could let impurities into the fuel system.
Also, a poorly fitting aftermarket cap can
cause the “Malfunction Indicator Light
(MIL)” to illuminate, due to fuel vapors
escaping from the system.
• A poorly fitting gas cap may cause the MIL
to turn on.
• To avoid fuel spillage and overfilling, do not
“top off” the fuel tank after filling.
WARNING!
• Never have any smoking materials lit in or
near the vehicle when the gas cap is re-
moved or the tank is being filled.
• Never add fuel when the engine is running.
This is in violation of most state and federal
fire regulations and may cause the mal-
function indicator light to turn on.
(Continued)
WARNING!(Continued)
• A fire may result if gasoline is pumped into
a portable container that is inside of a
vehicle. You could be burned. Always place
gas containers on the ground while filling.
NOTE:
• When the fuel nozzle “clicks” or shuts off,
the fuel tank is full.
• Tighten the gas cap about one-quarter
turn until you hear one click. This is an
indication that the cap is properly tight-
ened.
• If the gas cap is not tighten properly, the
MIL will come on. Be sure the gas cap is
tightened every time the vehicle is refu-
eled.
Emergency Fuel Filler Door Release
If you are unable to open the fuel filler door, use
the fuel filler door emergency release.
1. Open the liftgate.
2. Remove the left rear storage bin cover.
3. Pull the release cable.
Fuel Filler Door Release Switch
Fuel Filler Cap
243

Check the trailer tires for proper tire inflationpressures before trailer usage.
Check for signs of tire wear or visible tire damage before towing a trailer. Refer to
“Tires – General Information” in “Starting and
Operating” for proper inspection procedure.
When replacing tires, refer to “Tires – Gen- eral Information” in “Starting and Operating”
for proper tire replacement procedures. Re-
placing tires with a higher load carrying
capacity will not increase the vehicle’s
GVWR and GAWR limits.
Towing Requirements – Trailer Brakes
Do notinterconnect the hydraulic brake sys-
tem or vacuum system of your vehicle with
that of the trailer. This could cause inad-
equate braking and possible personal injury.
An electronically-actuated trailer brake con- troller is required when towing a trailer with
electronically-actuated brakes. When towing
a trailer equipped with a hydraulic surge-
actuated brake system, an electronic brake
controller is not required. Trailer brakes are recommended for trailers
over 1,000 lbs (454 kg), and required for
trailers in excess of 1,654 lbs (750 kg).
CAUTION!
If the trailer weighs more than 1,000 lbs
(454 kg) loaded, it should have its own brakes
and they should be of adequate capacity.
Failure to do this could lead to accelerated
brake lining wear, higher brake pedal effort,
and longer stopping distances.
WARNING!
• Do not connect trailer brakes to your vehi-
cle’s hydraulic brake lines. It can overload
your brake system and cause it to fail. You
might not have brakes when you need
them and could have an accident.
• Towing any trailer will increase your stop-
ping distance. When towing, you should
allow for additional space between your
vehicle and the vehicle in front of you.
Failure to do so could result in an accident. Towing Requirements – Trailer Lights and
Wiring
Whenever you pull a trailer, regardless of the
trailer size, stop lights and turn signals on the
trailer are required for motoring safety.
The Trailer Tow Package includes a 13 pin
wiring harness. Use a factory approved trailer
harness and connector.
NOTE:
Do not cut or splice wiring into the vehicles
wiring harness.
The electrical connections are all complete to
the vehicle but you must mate the harness to a
trailer connector.
248

Pin
Number Function Wire
Color
1 Left Turn Signal Black/ White
2 Rear Fog Light White
3
aGround/Common Return for Contacts (Pins) 1 and2and4to8 Brown
4 Right Turn Signal Black/ Green
5 Right Rear Position, Side Marker Lights, andRear Registration Plate Illumination Device.
b
Green/Red
Pin
Number Function Wire
Color
6 Stop Lights Black/ Red
7 Left Rear Position, Side Marker Lights, and Rear
Registration Plate Illumi- nation Device.
b
Green/Black
8 Reverse lights Blue/ Red
9 Permanent Power Sup- ply (+12V) Red
10 Power Supply Controlled by Ignition Switch(+12V) Yellow
11
aReturn for Contact (Pin) 10 Yellow/
Brown
12 Reserve for Future Allo- cation –
13
aReturn for Contact (Pin) 9 Red/
Brown
Note: The allocation pin 12 has been
changed from “Coding for coupled Trailer” to
“Reserve for Future Allocation.”
Pin
Number Function Wire
Color
aThe three return circuits shall not be con-
nected electrically in the trailer.
bThe rear position registration plate illumina-
tion device shall be connected such that no
light of the device has a common connection
with both pins 5 and 7.
Towing TipsBefore setting out on a trip, practice turning,
stopping and backing the trailer in an area
away from heavy traffic.
Automatic Transmission
The DRIVE range can be selected when tow-
ing. However, if frequent shifting occurs while in
this range, the TOW/HAUL mode (if equipped),
or a lower gear range, should be selected.
NOTE:
Using the TOW/HAUL mode (if equipped) or
selecting a lower gear range (using the Elec-
tronic Range Select (ERS) feature) while
operating the vehicle under heavy operating
conditions, will improve performance and
extend transmission life by reducing exces-13 - Pin Connector
249

sive shifting and heat buildup. This action
will also provide better engine braking.
The transmission fluid and filter should be
changed if you REGULARLY tow a trailer for
more than 45 minutes of continuous operation.
Refer to “Maintenance Schedule” for the proper
maintenance intervals.
NOTE:
Check the transmission fluid level before
towing (5.7L engine).
To help maintain a comfortable operating
temperature for your transmission, it is rec-
ommended that when towing a maximum
loaded trailer up steep grades with switch
backs, you should use the ERS function on
the transmission shifter to lock your vehicle
into first gear (5.7L Models Only).
Electronic Speed Control – If Equipped
Do not use in hilly terrain or with heavy loads.
When using the speed control, if you expe-rience speed drops greater than 10 mph
(16 km/h), disengage until you can get back
to cruising speed. Use speed control in flat terrain and with light
loads to maximize fuel efficiency.
Cooling System
To reduce potential for engine and transmission
overheating, take the following actions:
City Driving
When stopped for short periods of time, shift
the transmission into NEUTRAL and increase
engine idle speed.
Highway Driving
Reduce speed.
Air Conditioning
Turn off temporarily.
Trailer Hitch Attaching Points
Your vehicle will require extra equipment to tow
a trailer safely and efficiently. The trailer tow
hitch must be attached to your vehicle using
the provided attaching points on the vehicle’s
frame. Refer to the following chart to determine
the accurate attaching points. Other equip-
ment, such as trailer sway controls and braking
equipment, trailer equalizing (leveling) equip-
ment and low profile mirrors, may also be
required or strongly recommended.
Trailer Tow Hitch Attaching Points And Overhang Dimensions
Fixed, Detach
and Retractable Hitch
A 1.85 ft. (565 mm)
B 2.09 ft. (636 mm)
C 2.32 ft. (707 mm)
D 2.4 ft. (733 mm)
E 1.62 ft. (494 mm)
F 1.47 ft. (447 mm)
G (Maximum Overhang) 3.59 ft. (1093 mm)
250