2010 JAGUAR XFR 303 00

22.























23. CAUTION: Make sure that the torque wrench does not
move whilst tightening the VVT bolts.


NOTE: Make sure to tighten the exhaust VVT unit
bolts first.
Torque: 32 Nm Special Tool(s): 303-1482
















Install the oil suction tube.
Torque: 10 Nm

24.
25.
Install the special tool.
Special Tool(s): 303-1482






















CAUTIONS:


Apply the torque to the end of the special tool.


Make sure that the torque wrench is aligned with the
special tool as illustrated in the graphic.
Install the torque wrench to the special tool.
Torque: 35 Nm www.JagDocs.com

29.
30.
31.
Remove the special tool.
Special Tool(s): 303-1447















Install the special tool.
Special Tool(s): 303-1448
















CAUTION: Install the crankshaft pulley bolt with an
M16 washer to prevent damage to the crankshaft on
installation.
Torque: 50 Nm

32.
Remove the special tool.
Special Tool(s): 303-1448











33. Rotate the engine two complete turns clockwise.


34.
















35. CAUTION: Only rotate the crankshaft clockwise.
Install the special tool.
Special Tool(s): 303-1447













Install the special tool.
Special Tool(s): 303-1448

36.
37.
38.


























Remove the special tool.
Special Tool(s): 303-1448














CAUTIONS:


If the special tool cannot be installed, return to step
22 of the installation until the special tool 303-1445 is
installed correctly.


If directed to step 22, make sure that the VVT unit
retaining bolts are loosened prior to installing the special
tool(s).
Install the special tool.

Special Tool(s): 303-1445

42.
43.
Remove the special tool.
Special Tool(s): 303-1447














Torque: 10 Nm













44.
Refer to: Timing Cover (303-01C Engine - V8 5.0L Petrol, Removal and Installation).

45. Connect the battery ground cable.

Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

Engine - V8 S/C 5.0L Petrol - Valve Cover LH
Removal and Installation Published: 11-May-2011


Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Supercharger (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).

3. Refer to: Secondary Bulkhead Panel LH - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-02 Front End Body Panels, Removal and Installation).

4. Refer to: Air Cleaner Outlet Pipe LH (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).

5. Refer to: Fuel Rail LH (303-04E Fuel Charging and Controls - V8 S/C 5.0L Petrol, Removal and Installation).

6. Torque: 10 Nm 303-1446
Valve Cover Alignment Tool Special Tool(s)

Engine - V8 S/C 5.0L Petrol - Valve Cover RH
Removal and Installation Published: 11-May-2011


Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Supercharger (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).

3. Refer to: Secondary Bulkhead Panel RH - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-02 Front End Body Panels, Removal and Installation).

4. Refer to: Air Cleaner Outlet Pipe RH (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).

5. Refer to: Fuel Rail RH (303-04E Fuel Charging and Controls - V8 S/C 5.0L Petrol, Removal and Installation).


6. NOTE: Some variation in the illustrations may occur, but
the essential information is always correct. 303-1446
Valve Cover Alignment Tool Special Tool(s) www.JagDocs.com