2010 INFINITI M seat adjustment

To lower, push and hold the lock knob and push
the headrest down.Removal
Use the following procedure to remove the
adjustable headrests.
1. Pull the headrest up to the highest posi-tion.
2. Push and hold the lock knob.
3. Remove the headrest from the seat.
4. Store the headrest properly in a secure place so it is not loose in the vehicle.
5. Install and properly adjust the headrest before an occupant uses the seating po-
sition.
Install
1. Align the headrest stalks with the holes inthe seat. Make sure that the headrest is
facing the correct direction. The stalk with
the adjustment notches
s1must be in-
stalled in the hole with the lock knob
s2.
2. Push and hold the lock knob and push the headrest down.
3. Properly adjust the headrest before an occupant uses the seating position.
SSS0994SSS0995SSS0996
1-10Safety Ð Seats, seat belts and supplemental restraint system
wÐ
Ð
05/14/09Ðpattie
X

ARMREST
Front armrest
Pull the leversAup and slide the driver's or
passenger's armrest forward and backward.
Slide the armrest to the original position when
using the front cup holders.
Rear armrest
Pull the armrest down until it is horizontal.
Trunk pass-through
The rear center seatback can be folded to allow
trunk access from inside of the vehicle.
To access the trunk, pull down the rear center
armrest and pull out the trunk pass-through lid
s1.
To lock the lid, use the mechanical key and turn
it to the LOCK position
s2. To unlock, turn the
mechanical key to the UNLOCK position
s3. For
the mechanical key usage, see ªKEYSº in the ª3.
Pre-driving checks and adjustmentsº section.
Make sure that the mechanical key is removed
from the trunk pass-through lid key cylinder
before opening or closing the lid. Otherwise the
lid and the rear armrest may be damaged.
SIC2783SSS0520SSS0479
Safety Ð Seats, seat belts and supplemental restraint system1-11
wÐ
Ð
05/14/09Ðpattie
X

Center of rear seat
Selecting correct set of seat belts :
The center seat belt buckle is identified by the
CENTER mark
sA. The center seat belt tongue
can be fastened onlyinto the center seat belt
buckle.
Shoulder belt height adjustment
(front seats)
The shoulder belt anchor height should be
adjusted to the position best for you. (See
ªPRECAUTIONS ON SEAT BELT USAGEº earlier in
this section.)
To adjust, push the adjustment button
sA, and
then move the shoulder belt anchor to the
desired position, so that the belt passes over
the center of the shoulder. The belt should be
away from your face and neck, but not falling off
of your shoulder. Release the adjustment but-
ton to lock the shoulder belt anchor into posi-
tion.
WARNING
c After adjustment, release the adjustment
button and try to move the shoulder belt
anchor up and down to make sure it is se-
curely fixed in position.
c The shoulder belt anchor height should be
adjusted to the position best for you. Failure
to do so may reduce the effectiveness of the
entire restraint system and increase the
chance or severity of injury in an accident.
SEAT BELT EXTENDERS
If, because of body size or driving position, it is
not possible to properly fit the lap-shoulder belt
and fasten it, an extender is available that is
compatible with the installed seat belts. The
extender adds approximately 8 in (200 mm) of
length and may be used for either the driver or
front passenger seating position. See an
INFINITI retailer for assistance if an extender is
required.
WARNING
cOnly INFINITI seat belt extenders, made by
the same company which made the original
equipment seat belts, should be used with
the INFINITI seat belts.
SPA1836SSS0294A
1-18Safety Ð Seats, seat belts and supplemental restraint system
wÐ
Ð
05/14/09Ðpattie
X

cINFINITI recommends that the child restraint
be installed in the rear seat. According to
accident statistics, children are safer when
properly restrained in the rear seat than in
the front seat. If you must install a front-
facing child restraint in the front seat, see
ªCHILD RESTRAINT INSTALLATION USING
THE SEAT BELTSº later in this section.
c Improper use or improper installation of a
child restraint can increase the risk or sever-
ity of injury for both the child and other oc-
cupants of the vehicle and can lead to seri-
ous injury or death in an accident.
c Follow all of the child restraint manufactur-
er's instructions for installation and use.
When purchasing a child restraint, be sure to
select one which will fit your child and ve-
hicle. It may not be possible to properly in-
stall some types of child restraints in your
vehicle.
c If the child restraint is not anchored prop-
erly, the risk of a child being injured in a
collision or a sudden stop greatly increases.
c Child restraint anchor points are designed to
withstand only those loads imposed by cor-
rectly fitted child restraints. Under no cir-
cumstances are they to be used for adult
seat belts or harnesses. c
Adjustable seatbacks should be positioned
to fit the child restraint, but as upright as
possible.
c After attaching the child restraint, test it be-
fore you place the child in it. Push it from
side to side while holding the seat near the
LATCH attachment or by the seat belt path.
The child restraint should not move more
than 1 inch (25 mm) from side to side. Try to
tug it forward and check to see if the belt
holds the restraint in place. If the restraint is
not secure, tighten the belt as necessary, or
put the restraint in another seat and test it
again. You may need to try a different child
restraint. Not all child restraints fit in all
types of vehicles.
c When your child restraint is not in use, keep
it secured with the LATCH system or a seat
belt to prevent it from being thrown around
in case of a sudden stop or accident.
CAUTION
Remember that a child restraint left in a closed
vehicle can become very hot. Check the seating
surface and buckles before placing your child in
the child restraint. This vehicle is equipped with a universal child
restraint lower anchor system, referred to as the
Lower Anchors and Tethers for CHildren System
or LATCH. Some child restraints include two
rigid or webbing-mounted attachments that can
be connected to these lower anchors. For de-
tails, see ªLower Anchors and Tethers for CHil-
dren System (LATCH)º later in this section.
If you do not have a LATCH compatible child
restraint, the vehicle seat belts can be used.
(See ªCHILD RESTRAINT INSTALLATION USING
THE SEAT BELTSº later in this section.) In gen-
eral, child restraints are also designed to be
installed with a lap/shoulder seat belt.
Several manufacturers offer child restraints for
infants and small children of various sizes.
When selecting any child restraint, keep the
following points in mind:
c
Choose only a restraint with a label certify-
ing that it complies with Federal Motor Ve-
hicle Safety Standard 213 or Canadian Motor
Vehicle Safety Standard 213.
c Check the child restraint in your vehicle to
be sure it is compatible with the vehicle's
seat and seat belt system.
c If the child restraint is compatible with your
vehicle, place your child in the child restraint
and check the various adjustments to be
1-20Safety Ð Seats, seat belts and supplemental restraint system
wÐ
Ð
05/14/09Ðpattie
X

3. Secure the tether strap to tether anchorbracket that provides the straightest in-
stallation.
4. Tighten the strap according to the manu- facturer's instructions to remove any
slack.
If you have any questions when installing a top
tether strap child restraint on the rear seat, con-
sult your INFINITI retailer for details.
CHILD RESTRAINT INSTALLATION
USING LATCH
WARNING
cAttach LATCH system compatible child re-
straints only at the locations shown. For the
LATCH lower anchor locations, see ªLower
Anchors and Tethers for CHildren System
(LATCH)º earlier in this section. If a child
restraint is not secured properly, your child
could be seriously injured or killed in an
accident.
c The LATCH anchors are designed to with-
stand only those loads imposed by correctly
fitted child restraints. Under no circum-
stance are they to be used for adult seat
belts or harnesses.
c Inspect the lower anchors by inserting your
fingers into the lower anchor area and feel-
ing to make sure there are no obstructions
over the LATCH anchors, such as seat belt
webbing or seat cushion material. The child
restraint will not be secured properly if the
LATCH anchors are obstructed.
Front-facing
Follow these steps to install a front-facing child
restraint using LATCH system:
1. If your vehicle is equipped with rear power
seat adjustment, adjust the rear outboard
seats to the upright and rearmost posi-
tion. (See ªREAR SEATSº earlier in this
section.)
2. Position the child restraint on the seat. Always follow the child restraint manufac-
turer's instructions.
1-24Safety Ð Seats, seat belts and supplemental restraint system
wÐ
Ð
05/14/09Ðpattie
X

5. For child restraints that are equipped withwebbing-mounted attachments, remove
any additional slack from the anchor at-
tachments. Press downward and rearward
firmly in the center of the child restraint
with your knee to compress the vehicle
seat cushion and seatback while tighten-
ing the webbing of the anchor attach-
ments.
6. If the child restraint is equipped with a top tether strap, route the top tether strap
and secure the tether strap to the tether
anchor point. (See ªTOP TETHER STRAP
CHILD RESTRAINTº earlier in this section.) 7. After attaching the child restraint, test it
before you place the child in it. Push it
from side to side while holding the seat
near the LATCH attachment path. The
child restraint should not move more than
1 inch (25 mm) from side to side. Try to tug
it forward and check to see if the LATCH
attachment holds the restraint in place. If
the restraint is not secure, tighten the
LATCH attachment as necessary, or put
the restraint in another seat and test it
again. You may need to try a different
child restraint. Not all child restraints fit
in all types of vehicles. 8. Check to make sure the child restraint is
properly secured prior to each use. If the
child restraint is loose, repeat steps 4
through 7.
Rear-facing
Follow these steps to install a rear-facing child
restraint using LATCH system:
1. If your vehicle is equipped with rear powerseat adjustment, adjust the rear outboard
seats to the upright and rearmost posi-
tion. (See ªREAR SEATSº earlier in this
section.)
2. Position the child restraint on the seat. Always follow the child restraint manufac-
turer's instructions.
Front-facing Ð step 5
SSS0647
Front-facing Ð step 7
SSS0638
1-26Safety Ð Seats, seat belts and supplemental restraint system
wÐ
Ð
05/14/09Ðpattie
X

cINFINITI recommends that child restraints be
installed in the rear seat. However, if you
must install a front-facing child restraint in
the front passenger seat, move the passen-
ger seat to the rearmost position. Also, be
sure the front passenger air bag status light
is illuminated to indicate the passenger air
bag is OFF. See ªFront passenger air bag and
status lightº later in this section for details.
c The three-point seat belt in your vehicle is
equipped with an Automatic Locking Retrac-
tor (ALR) which must be used when installing
a child restraint.
c Failure to use the ALR mode will result in the
child restraint not being properly secured.
The restraint could tip over or otherwise be
unsecured and cause injury to the child in a
sudden stop or collision. Also, it can change
the operation of the front passenger air bag.
See ªFront passenger air bag and status
lightº later in this section.
c A child restraint with a top tether strap
should not be used in the front passenger
seat.
The instructions in this section apply to child
restraint installation using the vehicle seat
belts in the rear seat or the front passenger
seat.Front-facing
Follow these steps to install a front-facing child
restraint using the vehicle seat belt in the rear
seat or in the front passenger seat:
1. If your vehicle is equipped with rear power seat adjustment, adjust the rear outboard
seats to the upright and rearmost posi-
tion. (See ªREAR SEATSº earlier in this
section.)
If you must install a child restraint in the front
seat, it should be placed in a front-facing
direction only. Move the seat to the rearmost
position. Child restraints for infants must be
used in the rear-facing direction and there-
fore must not be used in the front seat.
Front-facing (front passenger seat) Ð step 1
SSS0640
Safety Ð Seats, seat belts and supplemental restraint system1-29
wÐ
Ð
05/14/09Ðpattie
X

Rear-facing
Follow these steps to install a rear-facing child
restraint using the vehicle seat belt in the rear
seat:
1.Child restraints for infants must be used in
the rear-facing direction and therefore
must not be used in the front seat.
If your vehicle is equipped with rear power
seat adjustment, adjust the rear outboard
seats to the upright and rearmost position.
(See ªREAR SEATSº earlier in this section.)
2. Position the child restraint on the seat.
Always follow the restraint manufacturer's
instructions. 3. Route the seat belt tongue through the
child restraint and insert it into the buckle
until you hear and feel the latch engage.
Be sure to follow the child restraint manu-
facturer's instructions for belt routing. 4. Pull the shoulder belt until the belt is fully
extended. At this time, the seat belt re-
tractor is in the Automatic Locking Retrac-
tor (ALR) mode (child restraint mode). It
reverts to the Emergency Locking Retrac-
tor (ELR) mode when the seat belt is fully
retracted.
SSS0100
Rear-facing Ð step 3
SSS0654
Rear-facing Ð step 4
SSS0655
Safety Ð Seats, seat belts and supplemental restraint system1-33
wÐ
Ð
05/14/09Ðpattie
X