2010 INFINITI G37 remove seats

HEAD RESTRAINTS WARNINGHead restraints supplement the other vehicle
safety systems. They may provide additional
protection against injury in certain rear end
collisions. Adjust the head restraints properly,
as specified in this section. Check the adjust-
ment after someone else uses the seat. Do not
attach anything to the head restraint stalks or
remove the head restraint. Do not use the seat
if the head restraint has been removed. If the
head restraint was removed, reinstall and prop-
erly adjust the head restraint before an occu-
pant uses the seating position. Failure to follow
these instructions can reduce the effectiveness
of the head restraints. This may increase the
risk of serious injury or death in a collision. The illustration shows the seating positions
equipped with head restraints. The head re-
straints are adjustable.
Indicates the seating position is
equipped with a head restraint.
Components 1. Head restraint
2. Adjustment notches
3. Lock knob
4. Stalk SSS0989 SSS0992
Safety — Seats, seat belts and supplemental restraint system
1-9
 —
—
10/12/09—tbrooks


Removal Use the following procedure to remove the
adjustable head restraints.
1. Pull the head restraint up to the highest
position.
2. Push and hold the lock knob.
3. Remove the head restraint from the seat.
4. Store the head restraint properly in a
secure place so it is not loose in the
vehicle.
Reinstall and properly adjust the head restraint
before an occupant uses the seating position. Install 1. Align the head restraint stalks with the
holes in the seat. Make sure that the head
restraint is facing the correct direction.
The stalk with the adjustment notches
 1
must be installed in the hole with the lock
knob
 2
.
2. Push and hold the lock knob and push the
head restraint down.
3. Properly adjust the head restraint before
an occupant uses the seating position. Front-seat Active Head Restraints The Active Head Restraint moves forward utiliz-
ing the force that the seatback receives from
the occupant in a rear-end collision. The move-
ment of the head restraint helps support the
occupant’s head by reducing its backward
movement and helping absorb some of the
forces that may lead to whiplash-type injuries.
Active Head Restraints are effective for colli-
sions at low to medium speeds in which it is
said that whiplash-type injury occurs most.
Active Head Restraints operate only in certain
rear-end collisions. After the collision, the head
restraints return to their original positions.
Adjust the Active Head Restraints properly as
described earlier in this section.SSS0995 SSS0996 SSS0508
Safety — Seats, seat belts and supplemental restraint system
1-11
 —
—
10/12/09—tbrooks


ARMREST (if so equipped)
Rear armrest Pull the armrest forward until it is horizontal.
Trunk pass-through The rear center seatback can be folded to allow
trunk access from inside of the vehicle.
To access the trunk, pull down the rear center
armrest and pull out the trunk pass-through lid
 1
.
To lock the lid, use the mechanical key and turn
it to the LOCK position
 3
. To unlock, turn the
mechanical key to the UNLOCK position
 2
. For
the mechanical key usage, see “KEYS” in the “3.
Pre-driving checks and adjustments” section.
Make sure that the mechanical key is removed
from the trunk pass-through lid key cylinder
before opening or closing the lid. Otherwise the
lid and the rear armrest may be damaged. PRECAUTIONS ON SEAT BELT USAGE If you are wearing your seat belt properly
adjusted, and you are sitting upright and well
back in your seat with both feet on the floor,
your chances of being injured or killed in an
accident and/or the severity of injury may be
greatly reduced. INFINITI strongly encourages
you and all of your passengers to buckle up
every time you drive, even if your seating
position includes a supplemental air bag.
Most U.S. states and Canadian provinces or ter-
ritories specify that seat belts be worn at all
times when a vehicle is being driven.SSS0678 SSS0677
SEAT BELTS
1-12 Safety — Seats, seat belts and supplemental restraint system
 —
—
10/12/09—tbrooks


Top tether anchor point locations Anchor points are located on the rear parcel
shelf. Installing top tether strap First, secure the child restraint with the lower
anchors (rear bench outboard seating positions
only) or the seat belt.
Flip up the tether anchor cover from the anchor
point which is located directly behind the child
seat. Position the top tether strap over the top
of the seatback and secure it to the tether
anchor bracket that provides the straightest
installation. Tighten the strap according to the
manufacturer’s instructions to remove any
slack.
If you have any questions when installing a top
tether strap child restraint on the rear seat, con-
sult your INFINITI retailer for details. CHILD RESTRAINT INSTALLATION
USING LATCH WARNING● Attach the LATCH system compatible child
restraints only at the locations shown. For
the LATCH lower anchor locations, see
“Lower Anchors and Tethers for CHildren
System (LATCH)” earlier in this section. If a
child restraint is not secured properly, your
child could be seriously injured or killed in
an accident.
● The LATCH anchors are designed to with-
stand only those loads imposed by correctly
fitted child restraints. Under no circum-
stance are they to be used for adult seat
belts or harnesses.
● Inspect the lower anchors by inserting your
fingers into the lower anchor area and feel-
ing to make sure there are no obstructions
over the LATCH anchors, such as seat belt
webbing or seat cushion material. The child
restraint will not be secured properly if the
LATCH anchors are obstructed.Coupe SSS0790
Safety — Seats, seat belts and supplemental restraint system
1-25
 —
—
10/12/09—tbrooks


Front-facing Follow these steps to install a front-facing child
restraint using the LATCH system:
1. Position the child restraint on the seat.
Always follow the child restraint manufac-
turer’s instructions. 2. Secure the child restraint anchor attach-
ments to the LATCH lower anchors. Check
to make sure the LATCH attachment is
properly attached to the lower anchor.
3. The back of the child restraint should be
secured against the vehicle seatback. If
the seating position does not have an
adjustable head restraint and it is inter-
fering with the proper child restraint fit,
try another seating position or a different
child restraint. 4. For child restraints that are equipped with
webbing mounted attachments, remove
any additional slack from the anchor at-
tachments. Press downward and rearward
firmly in the center of the child restraint
with your knee to compress the vehicle
seat cushion and seatback while tighten-
ing the webbing of the anchor attach-
ments.Front-facing (webbing-mounted) — step 2 SSS0645
Front-facing (rigid-mounted) — step 2 SSS0646
Front-facing — step 4 SSS0647
1-26 Safety — Seats, seat belts and supplemental restraint system
 —
—
10/12/09—tbrooks


Rear-facing Follow these steps to install a rear-facing child
restraint using LATCH system:
1. Position the child restraint on the seat.
Always follow the child restraint manufac-
turer’s instructions. 2. Secure the child restraint anchor attach-
ments to the LATCH lower anchors. Check
to make sure the LATCH attachment is
properly attached to the lower anchor. 3. For child restraints that are equipped with
webbing mounted attachments, remove
any additional slack from the anchor at-
tachments. Press downward and rearward
firmly in the center of the child restraint
with your hand to compress the vehicle
seat cushion and seatback while tighten-
ing the webbing of the anchor attach-
ments.Rear-facing (webbing-mounted) — step 2 SSS0648
Rear-facing (rigid-mounted) — step 2 SSS0649
Rear-facing — step 3 SSS0639
1-28 Safety — Seats, seat belts and supplemental restraint system
 —
—
10/12/09—tbrooks


● INFINITI recommends that child restraints be
installed in the rear seat. However, if you
must install a rear-facing child restraint in
the front passenger seat, move the passen-
ger seat to the rearmost position. Also, be
sure the front passenger air bag status light
is illuminated to indicate the passenger air
bag is OFF. See “Front passenger air bag and
status light” later in this section for details.
● The three-point seat belt in your vehicle is
equipped with an Automatic Locking Retrac-
tor (ALR) which must be used when installing
a child restraint.
● Failure to use the ALR will result in the child
restraint not being properly secured. The re-
straint could tip over or otherwise be unse-
cured and cause injury to the child in a sud-
den stop or collision.
● A child restraint with a top tether strap
should not be used in the front passenger
seat.
The instructions in this section apply to child
restraint installation using the vehicle seat
belts in the rear seat or the front passenger
seat. Front-facing Follow these steps to install a front-facing child
restraint using the vehicle seat belt in the rear
seat or in the front passenger seat:
1. If you must install a child restraint in the
front seat, it should be placed in a front-
facing direction only. Move the seat to the
rearmost position. Child restraints for in-
fants must be used in the rear-facing direc-
tion and therefore must not be used in the
front seat. 2. Position the child restraint on the seat.
Always follow the child restraint manufac-
turer’s instructions.
The back of the child restraint should be
secured against the seatback.
If necessary, adjust or remove the head
restraint (front passenger seat only) to ob-
tain the correct child restraint fit. (See
“HEAD RESTRAINTS” earlier in this section.)
If the head restraint is removed, store it in a
secure place. Be sure to reinstall the head
restraint when the child restraint is re-
moved.
If the seating position does not have an
adjustable head restraint and it is interfer-
ing with the proper child restraint fit, try
another seating position or a different child
restraint.Front-facing (front passenger seat) — step 1 SSS0640
1-30 Safety — Seats, seat belts and supplemental restraint system
 —
—
10/12/09—tbrooks


3. Route the seat belt tongue through the
child restraint and insert it into the buckle
until you hear and feel the latch engage.
Be sure to follow the child restraint manu-
facturer’s instructions for belt routing. 4. Pull the shoulder belt until the belt is fully
extended. At this time, the seat belt re-
tractor is in the Automatic Locking Retrac-
tor (ALR) mode (child restraint mode). It
reverts to Emergency Locking Retractor
(ELR) mode when the seat belt is fully
retracted. 5. Allow the seat belt to retract. Pull up on
the shoulder belt to remove any slack in
the belt.Front-facing — step 3 SSS0360B
Front-facing — step 4 SSS0651
Front-facing — step 5 SSS0652
Safety — Seats, seat belts and supplemental restraint system
1-31
 —
—
10/12/09—tbrooks