2010 INFINITI G37 battery

To connect the negative (  ) battery terminal,
perform the procedure in the following order.
Otherwise, the window and the side roof panel
may contact and be damaged.
1. Unlock and open the driver side door. Do
not close the door.
2. Open the hood.
3. Connect the negative (  ) battery terminal.
Then close the hood.
4. Fully open the driver side door window.
5. Close the driver side door and the win-
dow.
SEDAN AND COUPE WARNING● Do not expose the battery to flames or elec-
trical sparks. Hydrogen gas generated by
the battery is explosive. Do not allow battery
fluid to contact your skin, eyes, fabrics, or
painted surfaces. After touching a battery or
battery cap, do not touch or rub your eyes.
Thoroughly wash your hands. If the acid con-
tacts your eyes, skin or clothing, immedi-
ately flush with water for at least 15 minutes
and seek medical attention. ● Do not operate the vehicle if the fluid in the
battery is low. Low battery fluid can cause a
higher load on the battery which can gener-
ate heat, reduce battery life, and in some
cases lead to an explosion.
● When working on or near a battery, always
wear suitable eye protection and remove all
jewelry.
● Battery posts, terminals and related acces-
sories contain lead and lead compounds.
Wash hands after handling.
● Keep the battery out of the reach of children.
Check the fluid level in each cell (Remove the
battery cover if it is necessary). It should be
between the UPPER LEVEL
 1
and LOWER LEVEL
 2
lines.
If it is necessary to add fluid, add only distilled
water to bring the level to the indicator in each
filler opening. Do not overfill. DI0137MA
8-14 Maintenance and do-it-yourself
 —
—
04/21/10—debbie


1. Remove the cell plugs
 A
.
2. Add distilled water up to the UPPER LEVEL
 1
line.
If the side of the battery is not clear, check
the distilled water level by looking directly
above the cell; the condition
 1
indicates
OK and the conditions
 2
needs more to be
added.
3. Tighten cell plugs
 A
.
Vehicles operated in high temperatures or un-
der severe conditions require frequent checks
of the battery fluid level. JUMP STARTING If jump starting is necessary, see “JUMP START-
ING” in the “6. In case of emergency” section. If
the engine does not start by jump starting, the
battery may have to be replaced. Contact an
INFINITI retailer. CAUTION● Do not ground accessories directly to the
battery terminal. Doing so will bypass the
variable voltage control system and the ve-
hicle battery may not charge completely.
● Use electrical accessories with the engine
running to avoid discharging the vehicle
battery.
The variable voltage control system measures
the amount of electrical discharge from the
battery and controls voltage generated by the
generator.SDI1480C
VARIABLE VOLTAGE CONTROL SYSTEM
Maintenance and do-it-yourself
8-15
 —
—
04/21/10—debbie


ENGINE COMPARTMENT CAUTIONNever use a fuse of a higher or lower amperage
rating than that specified on the fuse box cover.
This could damage the electrical system or
cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1. Be sure the ignition switch is pushed to
the OFF or LOCK position and the head-
light switch is turned to OFF. 2. Open the engine hood and remove the
cover on the battery and the fuse/fusible
link holder.
3. Remove the fuse/fusible link holder
cover.
4. Remove the fuse with the fuse puller.
5. If the fuse is open
 A
, replace it with a
new fuse
 B
. Spare fuses are stored in the
passenger compartment fuse box.
6. If a new fuse also opens, have the elec-
trical system checked and repaired by an
INFINITI retailer.SDI1479A SDI1754
FUSES
8-20 Maintenance and do-it-yourself
 —
—
04/21/10—debbie


Replace the battery as follows:
1. Release the lock knob at the back of the
Intelligent Key and remove the mechanical
key.
2. Insert a flat-blade screwdriver
 A
wrapped with a cloth into the slit
 B
of
the corner and twist it to separate the
upper part from the lower part. 3. Replace the battery with a new one.
Recommended battery: CR2032 or equivalent.
● Do not touch the internal circuit and
electric terminals as it could cause a
malfunction.
● Hold the battery by the edges. Holding
the battery across the contact points will
seriously deplete the storage capacity.
● Make sure that the + side faces the
bottom of the case.
4. Align the tips of the upper and lower
parts, and then push them together until
it is securely closed.
5. Push the buttons two or three times to
check its operation. See an INFINITI retailer if you need any assis-
tance for replacement.
FCC Notice:
This equipment has been tested and found to
comply with the limits for a Class B digital device
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential in-
stallation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the in-
structions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equip-
ment and the receiver
– Connect the equipment into an outlet on a
circuit different from that to which the re-
ceiver is connected.
– Consult the retailer or an experienced
radio/TV technician for help.SDI1834 SDI2042
INTELLIGENT KEY BATTERY REPLACEMENT
8-22 Maintenance and do-it-yourself
 —
—
04/21/10—debbie


A vehicle equipped with All-Wheel Drive (AWD)
should never be tested using a two wheel
dynamometer (such as the dynamometers used
by some states for emissions testing), or similar
equipment. Make sure you inform test facility
personnel that your vehicle is equipped with
AWD before it is placed on a dynamometer.
Using the wrong test equipment may result in
transmission damage or unexpected vehicle
movement which could result in serious vehicle
damage or personal injury.
Due to legal requirements in some states/
areas, your vehicle may be required to be in
what is called the “ready condition” for an
Inspection/Maintenance (I/M) test of the emis-
sion control system.
The vehicle is set to the “ready condition” when
it is driven through certain driving patterns.
Usually, the “ready condition” can be obtained
by ordinary usage of the vehicle.
If a powertrain system component is repaired or
the battery is disconnected, the vehicle may be
reset to a “not ready condition”. Before taking
the I/M test, check the vehicle’s
inspection/maintenance test readiness condi-
tion. Push the ignition switch to the ON position
without starting the engine. If the Malfunction
Indicator Light (MIL) comes on steady for 20
seconds and then blinks for 10 seconds, the I/M test condition is “not ready”. If the MIL does not
blink after 20 seconds, the I/M test condition is
“ready”.
If the MIL indicates the vehicle is in a “not
ready” condition, drive the vehicle through the
following pattern to set the vehicle to the
“ready condition”. If you cannot or do not want
to perform the driving pattern, an INFINITI re-
tailer can conduct it for you.
WARNINGAlways drive the vehicle in a safe and prudent
manner according to traffic conditions and
obey all traffic laws.
1. Start the engine. Allow the engine to idle
until the engine coolant temperature
gauge needle points between the C and H
(normal operating temperature).
2. Accelerate the vehicle to 55 MPH (88
km/h), then quickly release the accelera-
tor pedal completely and keep it released
for at least 10 seconds.
3. Quickly depress the accelerator pedal for
a moment, then drive the vehicle at a
speed of 53 to 60 MPH (86 to 96 km/h) for
at least 9 minutes.
4. Stop the vehicle. Leave the engine run-
ning. 5. Accelerate the vehicle to 55 MPH (88
km/h) and maintain the speed for 2 min-
utes.
6. Repeat steps 4 and 5 at least 10 times.
7. Quickly release the accelerator pedal
completely and keep it released for at
least for 1 minute. Maintain the speed for
at least 5 minutes.
8. Stop the vehicle. Place the automatic
transmission selector lever in the P (Park)
or N (Neutral) position or the manual
transmission shift lever in the N (Neutral)
position.
9. Turn the engine off.
10. Start the engine and allow the engine to
idle for at least 2 hours.
11. Place the ignition switch to the OFF posi-
tion and leave the vehicle for at least 90
minutes.
If step 1 through 7 is interrupted, repeat the
preceding step. Any safe driving mode is ac-
ceptable between steps. Do not stop the engine
until step 7 is completed.READINESS FOR INSPECTION/
MAINTENANCE (I/M) TEST (US only)
9-24 Technical and consumer information
 —
—
04/21/10—debbie


10 Index 4 Wheel Active Steer (4WAS) system .... .5-54
4 Wheel Active Steer (4WAS) warning light . .2-13
A
ABS (Anti-lock Braking System) ....... .5-52
Advanced air bag system .......... .1-45
Air bag system
Advanced air bag system ........ .1-45
Front passenger air bag and status
light ..................... 1-47
Front-seat mounted side-impact
supplemental air bag system ....... 1-50
Roof-mounted curtain side-impact
supplemental air bag system ....... 1-50
Air bag warning labels ............ .1-53
Air bag warning light ......... .1-53 , 2-16
Air cleaner housing filter .......... .8-17
Air conditioner
Air conditioner service .......... .4-38
Air conditioner specification label .... 9-14
Air conditioning system refrigerant and
lubricant recommendations ....... 4-38
Automatic climate control ........ 4-28
In-cabin microfilter ............ 4-38
Operation (See automatic climate
control) ................... 4-28
Alarm, How to stop alarm
(see vehicle security system) ........ .2-28
Alcohol, drugs and driving .......... .5-6
All-wheel drive (AWD) ............ .5-43 All-wheel drive (AWD) driving safety
precautions ................... .5-7
All-wheel drive (AWD) warning light .... .2-12
Antenna .................... .4-84
Anti-lock Braking System (ABS) ....... .5-52
Anti-lock braking system (ABS) warning
light ...................... .2-12
Appearance care
Exterior appearance care ......... .7-2
Interior appearance care ..........7-4
Armrest .................... .1-12
Ashtrays (See cigarette lighter
and ashtrays) ................. .2-42
Audible reminders .............. .2-18
Audio operation precautions ........ .4-39
Audio system ................. .4-39
Audio system, Steering wheel
audio controls ................ .4-83
Autolight system ............... .2-33
Automatic
Automatic adjusting function (front
windows) ................. .2-52
Automatic
climate control ........ 4-30
Automatic transmission fluid (ATF) .... 8-11
Climate control .............. 4-28
Driving with automatic transmission . . . 5-12
Automatic door locks ............. .3-6
Automatic drive positioner ......... .3-28
Automatic seat positione r.......... .3-28
Average fuel consumption and speed . . . .2-25
Avoiding collision and rollover ........ .5-5 B
Battery ..................... .8-13
Battery
Battery saver system ........... .2-35
Intelligent Key ............... 8-22
Variable voltage control system ..... 8-15
Before starting the engine .......... .5-10
Belts (See drive belts) ............ .8-16
Bluetooth  hands-free phone system
(models with navigation system) ...... .4-85
Booster seats ................. .1-35
Brake
Anti-lock Braking System (ABS) ..... .5-52
Brake and clutch fluid ........... 8-12
Brake system ............... 5-48
Parking brake operation . . . ...... 5-18
Brake warning light ............. .2-12
Break-in schedule .............. .5-42
Brightness control and display ON/OFF
button ...................... .4-7
Brightness control, Instrument panel . . . .2-36
Bulb check/instrument panel . . . ..... .2-11
Bulb replacement .............. .8-23
C
Cabin air filter ................ .4-38
Capacities and recommended
fuel/lubricants ................. .9-2
 —
—
04/30/10—diane


INFINITI voice recognition system ..... .4-109
INFO button .................. .4-8
Inside mirror ................. .3-25
Inspection/maintenance (I/M) test ..... .9-24
Instrument brightness control ....... .2-36
Instrument panel ............... .2-3
Intelligent cruise control (ICC) system . . . .5-21
Intelligent cruise control (ICC) system main
switch indicator ............... .2-23
Intelligent Cruise Control (ICC) system
warning light ................. .2-14
Intelligent cruise control (ICC) system,
Preview function ............... .5-42
Intelligent Key ................. .3-2
Intelligent Key battery discharge
indicator .................... .2-22
Intelligent Key insertion indicator ..... .2-21
Intelligent Key removal indicator ...... .2-21
Intelligent Key system ............. .3-7
Intelligent Key system
Battery replacement ........... .8-22
Key operating range ............3-8
Key operation ............... 3-10
Warning light ................ 2-14
Warning signals .............. 3-12
Intelligent Key warning light ........ .2-14
Interior light control switch ......... .2-55
Interior light replacement .......... .8-25
Interior lights ................. .2-54
Interior trunk lid release .......... .3-20
iPod  player operation ............ .4-71
ISOFIX child restraint ............. .1-22 J
Jump starting .................. .6-7
K
Keyless entry (See remote keyless entry
system) .................... .3-14
Keys ....................... .3-2
Keys, For Intelligent Key system ....... .3-7
Labels
Air bag warning labels .......... .1-53
Air conditioner specification label .... 9-14
Emission
control
information label .... 9-13
Engine serial number ........... 9-12
F.M.V.S.S./C.M.V.S.S. certification
label ..................... 9-13
Tire and Loading information label . . . 9-14
Vehicle identification number (VIN) . . . 9-12
L
LATCH system ................. .1-22
License plate, Installing front license plate .9-15
Light
Air bag warning light ........... .1-53
Bulb replacement ............. 8-23
Fog light switch .............. 2-37
Headlight switch .............. 2-33
Headlights bulb replacement ....... 8-25
Indicator lights ............... 2-16
Interior light control switch ........ 2-55
Interior lights ............... 2-54 Map lights ................. 2-54
Trunk light ................. 2-56
Vanity mirror lights ............ 2-56
Warning/indicator lights and audible
reminders .................. 2-12
Xenon headlights ............. 2-32
Light replacement .............. .8-23
Lights, Exterior and interior light
replacement ................. .8-25
Loading information (See vehicle loading
information) .................. .9-17
Lock
Automatic door locks ........... .3-6
Door locks ..................3-4
Power door lock ...............3-4
Trunk lid .................. 3-18
Locking with mechanical key ......... .3-4
Low fuel warning ............... .2-22
Low outside temperature warning ..... .2-22
Low tire pressure warning light . . ..... .2-14
Low tire pressure warning system (See tire
pressure monitoring system (TPMS)) .... .5-3
Low washer fluid warning .......... .2-22
Maintenance
Battery ................... .8-13
General maintenance ............8-2
Indicators for maintenance
(dot
matrix) ................ 2-23
Inside
the vehicle ..............8-3
Maintenance precautions .........8-5
Maintenance requirements . . ......8-2
Outside the vehicle .............8-2
Seat belt maintenance .......... 1-20
10-4
 —
—
04/30/10—diane