2010 INFINITI G-CONVERTIBLE roof

Walk-in mechanism
This feature makes it easier to get in and out of
the rear seat. Use the following procedure when
getting in and out of the rear seat.
If the sun visor is used, close it to the original
position before operating the walk-in feature.
1. Pull the seatback lever upward1to fold
the front seatback down. Make sure that
the front seatback is completely folded
down.
2. To slide the front seat forward, push the seatback switch
2. The front seat will
move forward.
3. Get in or out of the vehicle. 4. To return the front seat to its original
position, raise the seatback and firmly
push the seatback switch
2again.
●To stop the seat sliding, push the seatback
switch
2again or push the seat sliding
switch.
● The front passenger seat will stop returning
7.0 in (177.6 mm) from its front-most posi-
tion to retain space for the rear passenger.
● Depending on the seat position, the head
restraint may contact the roof headlining
during the walk-in operation. To prevent
possible interference, lower the seat using
the seat lifter switch.
CAUTION
● When returning the seat to its original posi-
tion, confirm the seat and seatback are
locked properly.
● Be careful not to pinch your hand or foot or
bump your head when operating the walk-in
seat.
● Do not place any objects near the seatback
of the front seats. They may be pinched and
damaged.
● When operating the walk-in function, always
release the seat belt from the seat belt
guide. Otherwise, the seat belt guide may be
damaged.
The automatic forwarding and reversing will not
work or stop under the following conditions:
● When the vehicle speed is above 4 MPH (7
km/h) (driver’s seat only).
● When the seat belt is fastened.
● When the selector lever is not in the P (Park)
position (Automatic Transmission model’s
driver’s seat) or the parking brake is not
applied (Manual Transmission model’s driv-
er’s seat).
● When the door is closed.
SSS0786
1-6Safety — Seats, seat belts and supplemental restraint system
—
—
10/14/09—tbrooks


1. Roof in operation indicator
This indicator is displayed while the retractable
hard top is being operated.
2. Roof open indicator
This indicator is displayed when the retractable
hard top is open completely.
3. Roof close indicator
This indicator is displayed when the retractable
hard top is closed completely.
4. Check separator indicator
This indicator is displayed when the separator
is not set in the holder normally.
5. Check trunk indicator
This indicator is displayed when the trunk is not
closed completely.
NOTE:
A message is not displayed while the Intelligent
Cruise Control (ICC) system (if so equipped) is
being operated.
INDICATORS FOR MAINTENANCE
1. Engine oil replacement indicator
This indicator appears when the set time comes
for changing the engine oil. You can set or reset
the distance for changing the engine oil. (See
“TRIP COMPUTER” later in this section.)
2. Oil filter replacement indicator
This indicator appears when the set time comes
for replacing the oil filter. You can set or reset
the distance for replacing the oil filter. (See
“TRIP COMPUTER” later in this section.)
3. Tire replacement indicator
This indicator appears when the set time comes
for replacing tires. You can set or reset the
distance for replacing tires. (See “TRIP COM-
PUTER” later in this section.)
4. “OTHER” indicator
This indicator appears when the set time comes
for replacing items other than the engine oil, oil
filter and tires. You can set or reset the distance
for replacing the items. (See “TRIP COMPUTER”
later in this section.)
More maintenance reminders are also available
on the center display. (See “HOW TO USE INFO
BUTTON” in the “4. Monitor, climate, audio,
phone and voice recognition systems” section.)
SIC3281
Instruments and controls2-21
—
—
04/28/10—pattie


The auto reverse function can be activated when
the window is closed by automatic operation
when the ignition switch is in the ON position or
for 45 seconds after the ignition switch is
pushed to the OFF position.
Depending on the environment or driving condi-
tions, the auto reverse function may be activated
if an impact or load similar to something being
caught in the window occurs.
Automatic adjusting function
CAUTION
When the battery cable is removed from the
battery terminal, do not close either of the front
doors. The automatic window adjusting func-
tion will not work and the side roof panel may
be damaged.
The power window has an automatic adjusting
function. When the door is being opened, the
window is automatically lowered slightly to
avoid contact between the window and the side
roof panel. When the door is closed, the window
is automatically raised slightly.
While the automatic adjusting function does not
work, the window will be controlled as follows:
● When the door is opened, the window lowers
for approximately 0.39 in (10 mm). ●
While the door is open, the window cannot
be raised.
If the windows do not close
automatically
If the power window automatic function (closing
only) does not operate properly, perform the
following procedure to initialize the power win-
dow system.
1. Push the ignition switch to the ON posi- tion.
2. Close the door and hard top.
3. Open the window completely by operating the power window switch.
4. Pull the power window switch and hold it to close the window, and then hold the
switch more than 3 seconds after the
window is closed completely.
5. Release the power window switch. Oper- ate the window by the automatic function
to confirm the initialization is complete.
6. Perform steps 2 through 5 above for other windows.
If the power window automatic function does
not operate properly after performing the pro-
cedure above, have your vehicle checked by an
INFINITI retailer.
Automatic window lowering
When the retractable hard top operating switch
is pressed, the power windows will automati-
cally be lowered completely. The windows do
not rise automatically after the retractable hard
top operation is completed. Use the power
window switches to raise them.
2-46Instruments and controls
—
—
10/14/09—tbrooks


1. Retractable hard top indicators (in the dotmatrix liquid crystal display)
2. Retractable hard top operating switch
3. Hard top
4. Rear parcel shelf
5. Trunk lid
6. Separator
7. Side flapBEFORE OPERATING THE RETRACTABLE
HARD TOP
The retractable hard top on this vehicle is elec-
trically operated. You can fully open or close the
retractable hard top only by pushing the operat-
ing switch located on the center console.
The retractable hard top operating switch must
be operated under all of the following conditions.
● When the vehicle is stopped
● When the engine is running ●
When the separator is fixed in the position
separating the roof storage area and the
trunk room
● When the trunk lid is closed
CAUTION
Always keep the engine running while operat-
ing the retractable hard top. Even if the engine
stops, the retractable hard top will also operate
when the ignition switch is in the ON position,
but be sure to run the engine to prevent battery
discharge.
Be sure to follow the operating instructions and
all of the warnings and cautions in this section.
Improper operation of the retractable hard top
could cause a system malfunction, damage or
deterioration of the retractable hard top mate-
rial and related parts.
WARNING
● Park the vehicle in a safe and level location
and apply the parking brake.
Interior/exterior view
SPA2628
RETRACTABLE HARD TOP
3-18Pre-driving checks and adjustments
—
—
10/14/09—tbrooks


●Do not sit or place excessive weight on the
top, rear parcel shelf, side flaps and trunk
lid, especially when the retractable hard top
is being operated. The retractable hard top
may be damaged.
● Do not drive the vehicle with the retractable
hard top partially opened. Always make sure
the retractable hard top is either fully
opened or closed before driving.
● Secure items so that they cannot be blown
from the vehicle while driving with the re-
tractable hard top open.
● Do not install a roof rack or a roof carrier on
the retractable hard top. The retractable
hard top or the roof rack or both may be
damaged when the retractable hard top is
operated.
WHEN OPERATING THE RETRACTABLE
HARD TOP
WARNING
Keep hands and other parts of the body away
from moving parts such as the retractable hard
top, rear parcel shelf, side flaps, trunk lid and
power windows.
CAUTION
Do not place any items in the storage space for
the retractable hard top. A caution label is at-
tached on the floor in the retractable hard top
storage space. Cargo that contacts the retract-
able hard top may damage the retractable hard
top or cargo.
NOTE:
In case of low battery or low temperature, the
retractable hard top may temporarily stop mov-
ing during the operation. This functions to pro-
tect the retractable hard top control mechanism,
and it is not a malfunction.
If the retractable hard top is opened and closed
repeatedly in a short period of time, it may stop
moving to protect the retractable hard top mo-
tor. Wait for approximately 20 minutes before
operating the retractable hard top again.
Separator
The retractable hard top can be operated only
when the trunk room is separated.
SPA2629
3-20Pre-driving checks and adjustments
—
—
10/14/09—tbrooks


4. Push the OPEN side of the retractablehard top operating switch and hold it until
the retractable hard top is fully opened.
●When the OPEN side of the retractable
hard top operating switch is pushed a
beep sounds.
● “ROOF IN OPERATION” is displayed on the
dot matrix liquid crystal display while the
retractable hard top is in motion.
● The windows will automatically be fully
opened.
5. Release the switch when the retractable hard top is fully opened.
●When the retractable hard top is fully
opened, a beep sounds.
● “ROOF OPEN” is displayed on the dot
matrix liquid crystal display when the
retractable hard top is fully opened.
CAUTION
Be sure to fully open or fully close the retract-
able hard top and do not stop using the operat-
ing switch half way through the roof opening or
closing process. If the retractable hard top is
only partially opened, significant damage to
the retractable hard top could occur.
CLOSING THE RETRACTABLE HARD
TOP
1. Make sure the trunk lid is securely closed before operating the retractable hard top.
2. Apply the parking brake and move the selector lever to the P (Park) position (for
the automatic transmission models) or
the shift lever to the N (Neutral) position
(for the manual transmission models).
3. Start the engine. 4. Push the CLOSE side of the retractable
hard top operating switch and hold it until
the retractable hard top is fully closed.
●When the CLOSE side of the retractable
hard top operating switch is pushed a
beep sounds.
● “ROOF IN OPERATION” is displayed on the
dot matrix liquid crystal display while the
retractable hard top is in motion.
● The windows will automatically be fully
opened.
5. Release the switch when the retractable hard top is fully closed.
●When the retractable hard top is fully
closed, a beep sounds.
● “ROOF CLOSED” is displayed on the dot
matrix liquid crystal display when the
retractable hard top is fully closed.
IF THE RETRACTABLE HARD TOP DOES
NOT OPEN OR CLOSE ELECTRICALLY
If you cannot operate the retractable hard top
with the operating switch, first check whether
all the following operating conditions are satis-
fied.
● The vehicle is stopped
● The engine is running
SPA2633
Pre-driving checks and adjustments3-23
—
—
10/14/09—tbrooks


●The separator is fixed in the position sepa-
rating the roof storage area and the trunk
room
● Make sure that no objects interfere with the
rear parcel shelf, the side flaps and the
retractable hard top.
● The trunk lid is closed
If the retractable hard top still does not move
under the above conditions or has any system
malfunction, see an INFINITI retailer as soon as
possible.
WARNING
● Do not drive with the retractable hard top
partially opened.
● When the buzzer continuously sounds while
the vehicle is being driven, immediately park
the car in a safe location and check that the
retractable hard top is not partially open
● If the retractable hard top cannot be oper-
ated properly, see an INFINITI retailer as
soon as possible to have your vehicle
checked.OPERATING THE RETRACTABLE HARD
TOP USING THE INTELLIGENT KEY
The retractable hard top can be opened using
the request switch. This operation cannot close
the retractable hard top.
Opening the retractable hard top
Carry the Intelligent Key with you. Push the door
handle request switch (driver’s or passenger’s)
Aand hold it until the retractable hard top is
fully open.
INITIALIZING OF THE RETRACTABLE
HARD TOP
After replacing the battery or when repeating
open and close operations without fully open-
ing or closing the retractable hard top, the
retractable hard top may not operate normally.
If this situation occurs, perform initialization of
the retractable hard top according to the follow-
ing procedures.
1. Start the engine.
2. Push the OPEN side of the retractable
hard top operating switch and hold it.
3. Release the OPEN side of the retractable hard top operating switch when the beep
sounds once. The initialization of the re-
tractable hard top is complete.
If the beep sounds twice when releasing the
OPEN side of the retractable hard top operating
switch during the initialization, repeat the pro-
cedures from step 2.
CAUTION
After the initialization, if the retractable hard
top does not operate normally, immediately
contact INFINITI retailer for an inspection.
SPA2585
3-24Pre-driving checks and adjustments
—
—
10/14/09—tbrooks


Static and flutter: During signal interference
from buildings, large hills or due to antenna
position, usually in conjunction with increased
distance from the station transmitter, static or
flutter can be heard. This can be reduced by
lowering the treble setting to reduce the treble
response.
Multipath reception: Because of the reflective
characteristics of FM signals, direct and re-
flected signals reach the receiver at the same
time. The signals may cancel each other, result-
ing in momentary flutter or loss of sound.
AM radio reception
AM signals, because of their low frequency, can
bend around objects and skip along the ground.
In addition, the signals can be bounced off the
ionosphere and bent back to earth. Because of
these characteristics. AM signals are also sub-
ject to interference as they travel from transmit-
ter to receiver.
Fading: Occurs while the vehicle is passing
through freeway underpasses or in areas with
many tall buildings. It can also occur for several
seconds during ionospheric turbulence even in
areas where no obstacles exist.
Static: Caused by thunderstorms, electrical
power lines, electric signs and even traffic
lights.Satellite radio reception
When the satellite radio is used for the first time
or the battery has been replaced, the satellite
radio may not work properly. This is not a
malfunction. Wait more than 10 minutes with
the satellite radio ON and the vehicle outside of
any metal or large building for the satellite
radio to receive all of the necessary data.
The satellite radio mode requires an active XM
Satellite Radio subscription. The satellite radio
is not available in Alaska, Hawaii and Guam.
The satellite radio performance may be affected
if cargo carried on the roof blocks the satellite
radio signal.
If possible, do not put cargo near the satellite
antenna.
A build up of ice on the satellite radio antenna
can affect satellite radio performance. Remove
the ice to restore satellite radio reception.
Compact Disc (CD) player
●
Do not force a compact disc into the CD
insert slot. This could damage the CD and/or
CD player.
● Trying to load a CD with the CD door closed
could damage the CD and/or CD player.
SAA0480
Monitor, climate, audio, phone and voice recognition systems4-37
—
—
10/15/09—tbrooks