2010 INFINITI G-CONVERTIBLE manual transmission

GLOVE BOX
WARNING
Keep glove box lid closed while driving to help
prevent injury in an accident or a sudden stop.
To open the glove box, pull the handle
1.
To close, push the lid in until the lock latches.
To lock
2/unlock3the glove box, use the
mechanical key. For the mechanical key usage,
see “KEYS” in the “3. Pre-driving checks and
adjustments” section.
CONSOLE BOX
To open the console boxes, push the knobA
and pull up the lid.
To close, push the lid down until latched.
The inner tray (if so equipped) can be moved to
the front or rear position.
SIC3469
Automatic transmission models
SIC4363
Manual transmission models
SIC4174
2-42Instruments and controls
—
—
12/14/09—tbrooks


Removing the console lid (Manual
transmission model)
To remove the console lid:
1. Remove the hinge maskAusing a screw-
driver wrapped with a cloth.
2. Loosen four screws, and remove the lid.
3. Tighten the two outside screws
B.
4. Install the removed hinge mask
Ato the
original position.
STORAGE BOX (if so equipped)
To open, push the storage box lid1as illus-
trated.
Do not use the storage box as an ashtray.
Coupe — Manual transmission model
SIC3468
SIC4308
Instruments and controls2-43
—
—
10/14/09—tbrooks


INDICATORS FOR THE RETRACTABLE
HARD TOP
The retractable hard top indicator in the dot
matrix liquid crystal display
1shows the
conditions of retractable hard top operation.
The information displays when the retractable
hard top is being operated or if it is stopped
before reaching the fully opened or closed
position. For details about the retractable hard
top indicator, see “INDICATORS FOR RETRACT-
ABLE HARD TOP” in the “2. Instruments and
controls” section.
Automatic window lowering
When the retractable hard top operating switch
is pressed, the power windows will automati-
cally be lowered completely. The windows do
not rise automatically after the retractable hard
top operation is completed. Use the power
window switches to raise them.
OPENING THE RETRACTABLE HARD
TOP
1. Make sure the trunk lid is securely closed before operating the retractable hard top.
2. Apply the parking brake and move the selector lever to the P (Park) position (for
the automatic transmission models) or
the shift lever to the N (Neutral) position
(for the manual transmission models).
3. Start the engine.
SIC4293SPA2632
3-22Pre-driving checks and adjustments
—
—
10/14/09—tbrooks


4. Push the OPEN side of the retractablehard top operating switch and hold it until
the retractable hard top is fully opened.
●When the OPEN side of the retractable
hard top operating switch is pushed a
beep sounds.
● “ROOF IN OPERATION” is displayed on the
dot matrix liquid crystal display while the
retractable hard top is in motion.
● The windows will automatically be fully
opened.
5. Release the switch when the retractable hard top is fully opened.
●When the retractable hard top is fully
opened, a beep sounds.
● “ROOF OPEN” is displayed on the dot
matrix liquid crystal display when the
retractable hard top is fully opened.
CAUTION
Be sure to fully open or fully close the retract-
able hard top and do not stop using the operat-
ing switch half way through the roof opening or
closing process. If the retractable hard top is
only partially opened, significant damage to
the retractable hard top could occur.
CLOSING THE RETRACTABLE HARD
TOP
1. Make sure the trunk lid is securely closed before operating the retractable hard top.
2. Apply the parking brake and move the selector lever to the P (Park) position (for
the automatic transmission models) or
the shift lever to the N (Neutral) position
(for the manual transmission models).
3. Start the engine. 4. Push the CLOSE side of the retractable
hard top operating switch and hold it until
the retractable hard top is fully closed.
●When the CLOSE side of the retractable
hard top operating switch is pushed a
beep sounds.
● “ROOF IN OPERATION” is displayed on the
dot matrix liquid crystal display while the
retractable hard top is in motion.
● The windows will automatically be fully
opened.
5. Release the switch when the retractable hard top is fully closed.
●When the retractable hard top is fully
closed, a beep sounds.
● “ROOF CLOSED” is displayed on the dot
matrix liquid crystal display when the
retractable hard top is fully closed.
IF THE RETRACTABLE HARD TOP DOES
NOT OPEN OR CLOSE ELECTRICALLY
If you cannot operate the retractable hard top
with the operating switch, first check whether
all the following operating conditions are satis-
fied.
● The vehicle is stopped
● The engine is running
SPA2633
Pre-driving checks and adjustments3-23
—
—
10/14/09—tbrooks


TROUBLESHOOTING GUIDE
If the retractable hard top stops halfway during operation or does not operate normally, follow the procedures shown in the following table. If the
procedures in the following table do not solve the symptom, immediately contact INFINITI retailer for the inspection.
SymptomBeepPossible cause Possible solution
The OPEN side of the retractable hard
top operating switch is pushed, but
the retractable hard top does not
operate. Sounds twice
The OPEN side of the retractable hard top op-
erating switch is pushed while the retractable
hard top is fully open, or the CLOSE side of
the retractable hard top operating switch is
pushed while the retractable hard top is fully
closed. Push the CLOSE side of the retractable hard top
operating switch when the retractable hard top
is fully open. Push the OPEN side of the retract-
able hard top operating switch when the re-
tractable hard top is fully closed.
Sounds twice The selector lever (automatic transmission
models only) or the shift lever (manual trans-
mission models only) is in the R (Reverse)
position. Shift the selector lever (automatic transmission
models only) to the P (Park) or N (Neutral)
position, or shift the shift lever (manual trans-
mission model only) to the N (Neutral) position,
and then operate the retractable hard top.
Sounds twice The trunk lid is opened. Fully close the trunk lid.
Does not sound The battery voltage is low. Start the engine again and operate the retract-
able hard top.
Sounds twice The separator in the trunk room is not cor-
rectly set. Set the separator correctly. For details, refer to
“Separator” earlier in this section.
Does not sound The retractable hard top is in the deactivation mode in order to avoid motor overheating by
the continuous operation of the retractable
hard top. Wait for approximately 20 minutes without op-
erating the retractable hard top and then oper-
ate the retractable hard top.
3-26Pre-driving checks and adjustments
—
—
10/14/09—tbrooks


The automatic drive positioner system has two
features:
●Seat synchronization function
● Memory storage
SEAT SYNCHRONIZATION FUNCTION
The seat synchronization function automatically
adjusts the positions of the steering wheel and
outside mirrors when the seat is adjusted using
the power seat switches.
However, the steering wheel and outside mir-
rors will not move if the seat is adjusted over
the maximum thresholds. The system considers
that the steering wheel and outside mirror
adjustments are not necessary because the
seat may not be adjusted for the driving posi-
tion. Note that the function is set to disabled as
the factory default setting. The seat synchronization function operates un-
der the following conditions:
●
The ignition switch is in the ON position.
● The selector lever is in the P (Park) position
(Automatic Transmission models) or the
parking brake is applied (Manual Transmis-
sion models).
● The seatback is raised.
If the outside mirrors or the steering wheel
reaches its maximum adjustment, the function
is automatically disabled. Restart the function
by selecting a previously stored seat memory
position using the memory switches (1 or 2). An
Intelligent Key that was previously linked to the
stored seat memory can also be used to restart
the function.
If a seat position was not previously stored in
the seat memory, restart the function by adjust-
ing the steering wheel and outside mirrors
manually for your best driving position and then
drive the vehicle above 4 MPH (7 km/h).
SPA2659
AUTOMATIC DRIVE POSITIONER (if so
equipped)
Pre-driving checks and adjustments3-39
—
—
04/28/10—pattie


Cancel or activate seat
synchronization function
For Automatic Transmission models:
The selector lever must be in the P (Park)
position with the ignition switch in the ACC
position.
For Manual Transmission models:
The parking brake must be applied with the
ignition switch in the ACC position.
The seat synchronization function can be acti-
vated or canceled by pushing and holding the
SET switch for more than 10 seconds while the
ignition switch is in the ACC position.
The indicator lights on the memory switches (1
and 2) will blink once when the function is
canceled, and the indicator lights will blink
twice when the function is activated. Note that
the indicator lights may illuminate after 5 sec-
onds while holding the SET switch. This indi-
cates readiness for linking the Intelligent Key to
a stored memory position. Keep the SET switch
pushed for more than 10 seconds to turn on or
off the seat synchronization function.
MEMORY STORAGE
Two positions for the driver’s seat, steering
column and outside mirrors can be stored in the
automatic drive positioner memory. Follow
these procedures to use the memory system.
1.Automatic transmission models:
Move the selector lever to the P (Park)
position.
Manual transmission models:
Apply the parking brake.
2. Raise the seatback.
3. Push the ignition switch to the ON posi-
tion.
4. Adjust the driver’s seat, steering column and outside mirrors to the desired posi-
tions by manually operating each adjust-
ing switch. For additional information, see
“SEATS” in the “1. Safety — Seats, seat
belts and supplemental restraint system”
section and “TILT/TELESCOPIC STEERING”
page 3-34 and “OUTSIDE MIRRORS” ear-
lier in this section. 5. Push the SET switch and, within 5 sec-
onds, push the memory switch (1 or 2)
fully for at least 1 second.
The indicator light for the pushed memory
switch will stay on for approximately 5 sec-
onds after pushing the switch.
If memory is stored in the same memory
switch, the previous memory will be deleted.
Linking Intelligent Key to a stored
memory position
The Intelligent Key can be linked to a stored
memory position with the following procedure.
1. Follow the steps for storing a memoryposition.
2. While the indicator light for the memory switch being set is illuminated for 5 sec-
onds, push the
button on the Intel-
ligent Key. If the indicator light blinks, the
Intelligent Key is linked to that memory
setting.
Push the ignition switch to the OFF position,
and then push thebutton on the Intelli-
gent Key. The driver’s seat, steering wheel and
outside mirrors will move to the memorized
position.
3-40Pre-driving checks and adjustments
—
—
04/28/10—pattie


Confirming memory storage
●Push the ignition switch to the ON position
and push the SET switch. If the main memory
has not been stored, the indicator light will
come on for approximately 0.5 second.
When the memory has stored in position, the
indicator light will stay on for approximately
5 seconds.
● If the battery cable is disconnected, or if the
fuse opens, the memory will be canceled. In
this case, reset the desired position using
the previous procedure.
● If optional Intelligent Keys are added to your
vehicle, the memory storage procedure to
switch 1 or 2 and linking Intelligent Key
procedure to a stored memory position
should be performed again for each Intelli-
gent Key. For additional Intelligent Key infor-
mation, see “KEYS” earlier in this section.
Selecting the memorized position
1. Automatic transmission models:
Move the selector lever to the P (Park)
position.
Manual transmission models:
Apply the parking brake.
2. Raise the seatback.
3. Use one of the following methods to move
the driver’s seat, the outside mirrors and
the steering wheel.
●Push the ignition switch to the ON posi-
tion and push the memory switch (1 or 2)
fully for at least 1 second.
● Within 45 seconds of opening the driver’s
door, push the memory switch (1 or 2)
fully for at least 1 second.
The driver’s seat, steering column and
outside mirrors will move to the memo-
rized position with the indicator light
flashing, and then the light will stay on for
approximately 5 seconds.
For manual transmission models, the memory
positions can be selected even when the engine
is running. In this case, move the shift lever to
the N (Neutral) position and apply the parking
brake. Then, perform step 2.
SYSTEM OPERATION
The automatic drive positioner system will not
work or will stop operating under the following
conditions:
● When the vehicle speed is above 4 MPH (7
km/h).
● When the adjusting switch for the driver’s
seat and steering column is turned on while
the automatic drive positioner is operating.
● When the memory switch 1 or 2 is not
pushed for at least 1 second.
● When the seat, steering column and outside
mirrors have already been moved to the
memorized position.
● When no position is stored in the memory
switch.
● When the parking brake is released (MT
models).
● When the speed is above 4 MPH (7 km/h)
while the parking brake is applied (MT mod-
els).
To restart the drive positioner system, move
the parking brake to off and on.
● When the engine is started while moving the
automatic drive positioner.
Pre-driving checks and adjustments3-41
—
—
04/28/10—pattie