2010 INFINITI FX cruise control

PREVIEW FUNCTION (for Intelligent
Cruise Control system equipped
models)
The ICC system with the preview function iden-
tifies the need to apply emergency braking by
sensing the vehicle ahead in the same lane and
the distance to the vehicle ahead and relative
speed from it, it applies the brake pre-pressure
before the driver depresses the brake pedal and
helps improve brake response by reducing
pedal free play.
For more details, see “BRAKE ASSIST” later in
this section.The Distance Control Assist (DCA) system
brakes and moves the accelerator pedal upward
according to the distance from and the relative
speed of the vehicle ahead to help assist the
driver to maintain a following distance.
WARNING
●
Always drive carefully and attentively when
using the Distance Control Assist system.
Read and understand the Owner’s Manual
thoroughly before using the DCA system. To
avoid serious injury or death, do not rely on
the system to prevent accidents or to control
the vehicle’s speed in emergency situations.
Do not use the Distance Control Assist sys-
tem except in appropriate road and traffic
conditions.
● If the vehicle ahead comes to a stop, the
vehicle decelerates to a standstill within the
limitations of the system. The system will
cancel once it judges that the vehicle has
come to a standstill with a warning chime. To
prevent the vehicle from moving, the driver
must depress the brake pedal.
● The DCA system will not apply brake control
while the driver’s foot is on the accelerator
pedal.
PRECAUTIONS ON DISTANCE CONTROL
ASSIST SYSTEM
The system is intended to assist the driver to
keep a following distance from the vehicle
ahead traveling in the same lane and direction.
If the distance sensor
Adetects a slower
moving vehicle ahead, the system will reduce
the vehicle speed to help assist the driver to
maintain a following distance.
The system automatically controls the throttle
and applies the brakes (up to 25% of vehicle
braking power) if necessary.
The detection range of the sensor is approxi-
mately 390 ft (120 m) ahead.
SSD0738
DISTANCE CONTROL ASSIST (DCA) SYSTEM
(if so equipped)
Starting and driving5-49
—
—
08/03/09—pattie


●When ABS or VDC (including the traction
control system) is operating
● When driving into a strong light (i.e., sun-
light)
When the Conventional (fixed speed) cruise
control mode is operating, the DCA system will
not operate. (To use the DCA system, turn the
Conventional (fixed speed) cruise control mode
off, then push the DCA switch.)
For details about the Conventional (fixed speed)
cruise control mode, see “INTELLIGENT CRUISE
CONTROL (ICC) SYSTEM (FULL SPEED RANGE)”
earlier in this section.
When the engine is turned off, the system is
automatically turned off.
5-56Starting and driving
—
—
08/03/09—pattie


The stoplights of the vehicle come on and the
brake pedal depresses when braking is per-
formed by the DCA system.
When the brake operates, a noise may be heard.
This is not a malfunction.
WARNING
●When the vehicle ahead detection indicator
light is not illuminated, system will not con-
trol or warn the driver.
● Never place your foot under the brake pedal.
Your foot may be caught when the system
controls the brake.
● Depending on the position of the accelerator
pedal, the system may not be able to assist
the driver to release the accelerator pedal
appropriately.
● If the vehicle ahead comes to a standstill,
the vehicle decelerates to a standstill within
the limitations of the system. The system
will release brake control with a warning
chime once it judges the vehicle is at a
standstill. To prevent the vehicle from mov-
ing, the driver must depress the brake pedal.
(The system will resume control automati-
cally once the system reaches 3 MPH
(5 km/h)). Overriding the system :
The following driver’s operation overrides the
system operation.
●
When the driver depresses the accelerator
pedal even further while the system is mov-
ing the accelerator pedal upward, the DCA
system control of the accelerator pedal is
canceled.
● When the driver’s foot is on the accelerator
pedal, the brake control by the system is not
operated.
● When the driver’s foot is on the brake pedal,
neither the brake control nor the alert by the
system operates.
● When the Intelligent Cruise Control system is
set, the DCA system will be cancelled.
Approach warning
If your vehicle comes closer to the vehicle
ahead due to rapid deceleration of that vehicle
or if another vehicle cuts in, the system warns
the driver with the chime and DCA system
display. Decelerate by depressing the brake
pedal to maintain a safe vehicle distance if:
● The chime sounds.
● The vehicle ahead detection indicator blinks.
The warning chime may not sound in some
cases when there is a short distance between
vehicles. Some examples are:
● When the vehicles are traveling at the same
speed and the distance between vehicles is
not changing
● When the vehicle ahead is traveling faster
and the distance between vehicles is in-
creasing
● When a vehicle cuts in near your vehicle
The warning chime will not sound when your
vehicle approaches vehicles that are parked or
moving slowly.
5-58Starting and driving
—
—
08/03/09—pattie


Sensor maintenance
How to handle the sensor :
The sensor for the DCA system is common with
Intelligent Cruise Control and is located below
the front bumper.
To handle the sensor, see “INTELLIGENT CRUISE
CONTROL (ICC) SYSTEM (FULL SPEED RANGE)”
earlier in this section.The Forward Collision Warning (FCW) system
will warn the driver by a warning light and
chime when your vehicle is getting close to the
vehicle ahead in the traveling lane.
The FCW system will function when your vehicle
is driven at speeds of approximately 10 MPH (15
km/h) and above.
SSD0738
Vehicle ahead detection light
SSD0749
FORWARD COLLISION WARNING (FCW)
SYSTEM (if so equipped)
Starting and driving5-61
—
—
08/03/09—pattie


FCW system operation
The FCW system will function at speeds of
approximately 10 MPH (15 km/h) and above,
when the system turns on.
The FCW system has an automatic setting mode
and a manual setting mode to turn the system
on. The setting mode can be changed. In the
automatic setting mode, the FCW system is
automatically turned on when the ignition
switch is pushed to the ON position. When the
FCW system is on, the FCW/LDW ON indicator
light
1on the FCW/LDW switch illuminates. To
cancel the FCW system, push the FCW/LDW
switch. The FCW/LDW ON indicator light will turn off. To turn on the system, push the
FCW/LDW switch again.
When the FCW switch is pushed, the LDW
system will also turn on or off simultaneously.
See “LANE DEPARTURE WARNING (LDW) SYS-
TEM” earlier in this section.
In the manual setting mode, you need to push
the FCW/LDW switch to turn on the system after
the ignition switch is pushed to the ON posi-
tion.
The setting mode can be changed using the
FCW/LDW switch. To change the setting mode,
push and hold the FCW/LDW switch for more
than 4 seconds when the FCW/LDW ON indica-
tor is off. When the mode is changed, a chime
sounds and the lane departure warning light
(orange) flashes.
For the sensor maintenance, see “INTELLIGENT
CRUISE CONTROL (ICC) SYSTEM (FULL SPEED
RANGE)” earlier in this section.
The Intelligent Brake Assist (IBA) system warns
the driver by a warning light and chime when
there is a risk of a collision with the vehicle
ahead in the traveling lane and the driver must
take avoidance action immediately. The system
helps reduce the rear-end collision speed by
applying the brakes when the system judges
that the collision cannot be prevented.
The IBA system will function when your vehicle
is driven at speeds of approximately 10 MPH (15
km/h) and above, and when your vehicle is
driven at speeds approximately 10 MPH (15
km/h) faster than the vehicle ahead.
FCW/LDW switch
SIC3832
INTELLIGENT BRAKE ASSIST (IBA) SYSTEM
(if so equipped)
5-64Starting and driving
—
—
08/03/09—pattie


The IBA system will remain in the last ON or OFF
state it was left in until it is manually changed
by pressing the IBA OFF switch.
Illumination of the IBA OFF indicator light with-
out the warning chime sound is an indication
that the IBA system is temporarily unavailable.
It will occur under the following conditions:
– When driving into a strong light (for example,sunlight)
The IBA OFF indicator light will turn off when the
system returns to its normal operating condi-
tions.
For the sensor maintenance, see “INTELLIGENT
CRUISE CONTROL (ICC) SYSTEM (FULL SPEED
RANGE)” earlier in this section.CAUTION
During the first 1,200 miles (2,000 km), follow
these recommendations to obtain maximum
engine performance and ensure the future reli-
ability and economy of your new vehicle.
Failure to follow these recommendations may
result in shortened engine life and reduced en-
gine performance.
● Avoid driving for long periods at constant
speed, either fast or slow. Do not run the
engine over 4,000 rpm.
● Do not accelerate at full throttle in any gear.
● Avoid quick starts.
● Avoid hard braking as much as possible.
● Do not tow a trailer for the first 500 miles
(805 km). ●
Accelerate slowly and smoothly. Maintain
cruising speeds with a constant accelerator
position.
● Drive at moderate speeds on the highway.
● Avoid unnecessary stopping and braking.
Keep a safe distance behind other vehicles.
● Select a gear range suitable to road condi-
tions.
● Avoid unnecessary prolonged engine idling.
● Keep your engine tuned up.
● Follow the recommended periodic mainte-
nance schedule.
● Keep the tires inflated at the correct pres-
sure. Improper tire pressure will increase
wear and waste fuel.
● Make sure the front wheels are properly
aligned. Improper alignment will cause pre-
mature tire wear and lower fuel economy.
● Climate control operation lowers fuel
economy. Use the air conditioner only when
necessary.
● When cruising at highway speeds, it is more
economical to use the air conditioner and
leave the windows closed to reduce drag.
BREAK-IN SCHEDULE INCREASING FUEL ECONOMY
5-68Starting and driving
—
—
08/03/09—pattie


BRAKE ASSIST
When the force applied to the brake pedal
exceeds a certain level, the Brake Assist is
activated generating greater braking force than
a conventional brake booster even with light
pedal force.
WARNING
The Brake Assist is only an aid to assist braking
operation and is not a collision warning or
avoidance device. It is the driver’s responsibil-
ity to stay alert, drive safely and be in control of
the vehicle at all times.
PREVIEW FUNCTION (Intelligent Cruise
Control system equipped models)
When the Preview Function identifies the need
to apply emergency braking by sensing a ve-
hicle ahead in the same lane and the distance
and relative speed from it, it applies the brake
pre-pressure before the driver depresses the
brake pedal and helps improve brake response
by reducing pedal free play.
●This system will not operate when the ve-
hicle is moving at approximately 20 MPH (32
km/h) or less. ●
The pre-pressure function ceases when the
following conditions are met:
a) When the driver depresses the accelera- tor pedal or the brake pedal.
b) If the driver does not operate the accel- erator or brake pedal within approxi-
mately 1 second.
●The sensor will not detect:
a) Pedestrians or objects in the roadway
b) Oncoming vehicles in the same lane
c) Motorcycles traveling offset in the
travel lane as illustrated
WARNING
●This system is only an aid to assist braking
operation and is not a collision warning or
avoidance device. It is the driver’s responsi-
bility to stay alert, drive safely and be in
control of the vehicle at all times.
SSD0338
BRAKE ASSIST
5-74Starting and driving
—
—
08/03/09—tbrooks


How to handle the sensor
The sensor for the Preview Function is common
with Intelligent Cruise Control and is located
below the front bumper.
To keep the Preview Function operating prop-
erly, be sure to observe the following:
●Always keep the sensor clean. Wipe with a
soft cloth carefully so as not to damage the
sensor.
● Do not strike or damage the areas around
the sensor. Do not touch or remove the
screw located on the sensor. Doing so could
cause failure or malfunction. If the sensor is
damaged due to an accident, contact an
INFINITI retailer.
● Do not attach a sticker (including transpar-
ent material) or install an accessory near the
sensor. This could cause failure or malfunc-
tion.
ANTI-LOCK BRAKING SYSTEM (ABS)
WARNING
● The Anti-lock Braking System (ABS) is a so-
phisticated device, but it cannot prevent ac-
cidents resulting from careless or dangerous
driving techniques. It can help maintain ve-
hicle control during braking on slippery sur-
faces. Remember that stopping distances on
slippery surfaces will be longer than on nor-
mal surfaces even with ABS. Stopping dis-
tances may also be longer on rough, gravel
or snow covered roads, or if you are using
tire chains. Always maintain a safe distance
from the vehicle in front of you. Ultimately,
the driver is responsible for safety.
● Tire type and condition may also affect brak-
ing effectiveness.
– When replacing tires, install the specified size of tires on all four wheels.
– When installing a spare tire, make sure that it is the proper size and type as speci-
fied on the Tire and Loading Information
label. See “TIRE AND LOADING INFORMA-
TION LABEL” in the “9. Technical and con-
sumer information” section of this
manual. – For detailed information, see “WHEELS
AND TIRES” in the “8. Maintenance and
do-it-yourself” section of this manual.
The Anti-lock Braking System (ABS) controls the
brakes so the wheels do not lock during hard
braking or when braking on slippery surfaces.
The system detects the rotation speed at each
wheel and varies the brake fluid pressure to
prevent each wheel from locking and sliding. By
preventing each wheel from locking, the system
helps the driver maintain steering control and
helps to minimize swerving and spinning on
slippery surfaces.
Using the system
Depress the brake pedal and hold it down.
Depress the brake pedal with firm steady pres-
sure, but do not pump the brakes. The ABS will
operate to prevent the wheels from locking up.
Steer the vehicle to avoid obstacles.
WARNING
Do not pump the brake pedal. Doing so may
result in increased stopping distances.
5-76Starting and driving
—
—
08/03/09—pattie