2010 INFINITI FX clock

Getting the spare tire and tools
1. Remove the cargo cover (if so equipped).
See “CARGO COVER” in the “2. Instruments
and controls” section.
2. Raise the luggage room floor cover usingthe handle
A, then hang it on the edge of
the luggage room opening using the hook
B.
Remove jacking tools and the spare tire located
under the luggage room.
Turn the retainer counterclockwise
A, remove
the subwoofer
B(if so equipped) and place it
on the side of the luggage room (with the flat
surface facing down), then remove the spare
tire. Be careful not to let the subwoofer fall
down.
Jacking up the vehicle and removing
the damaged tire
WARNING
● Never get under the vehicle while it is sup-
ported only by the jack. If it is necessary to
work under the vehicle, support it with
safety stands.
● Use only the jack provided with your vehicle
to lift the vehicle. Do not use the jack pro-
vided with your vehicle on other vehicles.
The jack is designed for lifting only your ve-
hicle during a tire change.
● Use the correct jack-up points. Never use any
other part of the vehicle for jack support.
● Never jack up the vehicle more than
necessary.
● Never use blocks on or under the jack.
● Do not start or run the engine while vehicle is
on the jack, as it may cause the vehicle to
move. This is especially true for vehicles
with limited slip differentials.
● Do not allow passengers to stay in the ve-
hicle while it is on the jack.
Carefully read the caution label attached to the
jack body and the following instructions.
SCE0766SCE0767
6-4In case of emergency
—
—
08/03/09—pattie


1. Place the jack directly under the jack-uppoint as illustrated so the top of the jack
contacts the vehicle at the jack-up point.
Align the jack head between the two
notches in the front or the rear as shown.
Also fit the groove of the jack head be-
tween the notches as shown.
The jack should be used on level firm ground.
2. Loosen each wheel nut one or two turns by turning counterclockwise with the
wheel nut wrench. Do not remove the
wheel nuts until the tire is off the ground. 3. Carefully raise the vehicle until the tire
clears the ground. To lift the vehicle,
securely hold the jack lever and rod with
both hands as shown above. Remove the
wheel nuts, and then remove the tire.
Jack-up point
SCE0771SCE0504
In case of emergency6-5
—
—
08/03/09—tbrooks


CAUTION
Be careful not to burn yourself, as the engine oil
is hot.●Waste oil must be disposed of properly.
● Check your local regulations.
4. (Perform steps 4 to 7 only when the
engine oil filter change is needed.)
Loosen the oil filter2with an oil filter
wrench. Remove the oil filter by turning it by
hand.
5. Wipe the engine oil filter mounting sur- face with a clean rag.
CAUTION
Be sure to remove any old rubber gasket re-
maining on the mounting surface of the engine.
Failure to do so could lead to engine damage.
6. Coat the gasket on the new filter with clean engine oil. 7. Screw in the oil filter clockwise until a
slight resistance is felt, then tighten ad-
ditionally more than 2/3 turn.
Oil filter tightening torque:11 to 15 ft-lb
(14.7 to 20.5 N·m)
8. Clean and re-install the drain plug with a new washer. Securely tighten the drain
plug with a wrench.
Drain plug tightening torque:22 to 29 ft-lb
(29 to 39 N·m)
Do not use excessive force.
9. Refill engine with recommended oil and install the oil filler cap securely.
CAUTION
The dipstick must be inserted in place to pre-
vent oil spillage from the dipstick hole while
filling the engine with oil.
See “CAPACITIES AND RECOMMENDED
FUEL/LUBRICANTS” in the “9. Technical and
consumer information” section for drain and
refill capacity. The drain and refill capacity
depends on the oil temperature and drain time.
Use these specifications for reference only. Always use the dipstick to determine the proper
amount of oil in the engine.
10. Start the engine and check for leakage
around the drain plug and the oil filter.
Correct as required.
11. Turn the engine off and wait more than 15 minutes. Check the oil level with the
dipstick. Add engine oil if necessary.
After the operation
1. Install the engine undercover into positionas the following steps.
a. Pull the center of the small plastic clip out.
b. Hold the engine undercover into position.
c. Insert the clip through the undercover into the hole in the frame, then push the
center of the clip in to lock the clip in
place.
d. Install the other bolts that hold the un- dercover in place. Be careful not to strip
the bolts or over-tighten them.
2. Lower the vehicle carefully to the ground.
3. Dispose of waste oil and filter properly.
8-12Maintenance and do-it-yourself
—
—
08/03/09—pattie


C
Cabin air filter ................ .4-45
Capacities and recommended
fuel/lubricants ................. .9-2
Car phone or CB radio ............4-103
Card holder .................. .2-49
Cargo (See vehicle loading information) . . .2-50
Cargo cover .................. .2-51
Cargo light .................. .2-60
Cargo net ................... .2-50
Catalytic converter, Three way catalyst . . . .5-2
Center multi-function control panel ......4-2
Child restraints ................ .1-20
Child restraints Booster seats ............... .1-35
Installation using LATCH .........1-25
Installation using the seat belts .....1-29
LATCH system ............... 1-22
Precautions on child restraints ......1-20
Top tether strap .............. 1-24
Child safety .................. .1-15
Child safety rear door lock ...........3-6
Chimes Audible reminders .............2-20
Seat belt warning light and chime ....2-17
Circuit breaker, Fusible link ..........8-22
Cleaning exterior and interior ......7-2 , 7-4
Climate control Automatic climate control .........4-40
Clock ..................... .2-45
Coat hooks .................. .2-49
Cockpit ..................... .2-2
Cold weather driving ............. .5-80Command (See Bluetooth
Hands-Free
Phone System) ............4-105 , 4-121
Compact Disc (CD) player
(See audio system) ............. .4-63
Compact spare tire ............. .8-38
Compass .................... .2-9
Console box ..................2-48
Continuous

Damping Control .........5-72
Controller, Center multi-function control
panel ...................... .4-4
Controls Control panel button (display) .......4-2
Heater and air conditioner controls
(See automatic climate control) .....4-40
Coolant
Capacities and recommended fuel/
lubricants .................. .9-2
Changing engine coolant .........8-10
Checking engine coolant level ......8-9
Corrosion protection ..............7-6
Cover, Cargo cover .............. .2-51
Cruise control ................. .5-26
Cruise control, Fixed speed cruise control
(on ICC system) ................ .5-45
Cruise indicator ............... .2-24
Cup holders .................. .2-46
Current fuel consumption ...........2-27
D
Daytime running light system ........2-38
Defroster switch, Rear window and outside
mirror defroster switch ............2-35
Dimensions .................. .9-10
Display cleaning ................ .4-5Display controls (See center multi-function
control panel)
................. .4-2
Distance Control Assist (DCA) system . . . .5-49
Distance Control Assist (DCA) system
switch indicator ............... .2-25
Distance Control Assist (DCA) system
warning light ................. .2-14
Distance to empty .............. .2-27
Door/lift gate open warning .........2-24
Dot matrix liquid crystal display .......2-21
Drive belts ................... .8-17
Drive positioner ............... .3-25
Driving All-wheel drive (AWD) ...........5-69
Cold weather driving ...........5-80
Driving with automatic transmission . . . 5-13
On-pavement and off-road driving ....5-5
Precautions when starting and driving . . 5-2
Safety precautions .............5-7
DS (Drive Sport) mode .............5-15
E
Economy, Fuel ................ .5-68
Elapsed time ................. .2-27
Elapsed

time and trip odometer .......2-27
Emission control information label ......9-12
Emission control system warranty ......9-29
Engine Before starting the engine .........5-12
Break-in schedule ............. 5-68
Capacities and recommended fuel/
lubricants ..................9-2
Changing engine coolant .........8-10
Changing engine oil and filter . . . . . . 8-11
10-2
—
—
10/19/09—tbrooks