Indicators/Info
Display/MID/TPMS
Instrument Panel Indicators
Briefly appear with each engine start. Red and amber indicators are most critical. Blue and green
indicators are used for general information.
ABS (anti-lock brake system)
DRL (daytime running lights)
Malfunction lamp (check engine light)
TPMS (tire pressure monitoring system)
VSA (vehicle stability assist)
Malfunction Indicators: If an indicator remains on, there may be a problem; see your dealer.
Charging system
Low oil pressure
SRS (supplemental restraint system)
Low brake fluid
VTM-4 (Variable torque
management 4WD)
10 Ridgeline TRG_Inside Front:Inside Cvr 7/6/2009 10:03 AM Page 1 2010 Ridgeline
On/Off Indicators
Condition Indicators:Action is needed by driver.
PASSENGER
AIRBAG
OFF
SIDE AIRBAG OFF
VSA solid: off
Blinks: activated
CRUISE CONTROL on
CRUISE MAIN on
Immobilizer Flashes: improperly coded key;
use correct key
Headlights on
Turn signals/hazards onBed lights onHigh beams on
Seat belt reminder:
Fasten seat belt(s)
Low fuel: RefillLow tire pressure:
Add air
Maintenance minder:
Make appointment
Parking brake on: Release
Back window open:
Close back windowVTM-4 (blinks):
Pull over
Message indicator*:
Press Info button*Models with navigation onlyA/T temperature:
Pull over
Washer level:
Add fluid
Door/tailgate open:
Close door(s) / tailgate
PASSENGER AIRBAG
OFF
(above Hazard
Warning button)
10 Ridgeline TRG_1ab:ExtraPages.qxd 7/6/2009 10:05 AM Page a1 2010 Ridgeline
HomeLink®(if equipped)
Press and hold the button on the
remote transmitter and the HomeLink
button at the same time. Then, while
continuing to hold the HomeLink button,
press and release the button on the
remote transmitter every 2 seconds.
Does the LED blink at a faster rate within 20
seconds?
Press and hold
the HomeLink
button again. Training
complete
YES
NO
HomeLink indicator
flashes for 2 seconds,
then remains on. HomeLink LED
remains on.YES
NO YES
NO
Position the remote transmitter you
wish to link 1–3 inches from the
HomeLink button you want to program.1
Press and hold the desired
HomeLink but ton and the button on
the remote transmitter.
Does the HomeLink indicator (LED) blink at a
faster rate after about 10 seconds?
2
aThe remote has a rolling code.
Press the “learn” button on the
remote-controlled device (e.g.,
garage door opener).
Press the programmed HomeLink
button again; the remote-controlled
device should operate. Within 30 seconds, press and
hold the programmed HomeLink
button for 2 seconds.a
Press and hold the programmed
HomeLink button for about a
second.
Does the device (garage door opener) work?
3
b
4
5
Training a Button
Indicator remains
on for about 25
seconds (standard
transmitter). Indicator flashes rapidly
for 2 seconds, then
remains on for about 23
seconds (rolling code
transmitter).
Press and hold the desired
HomeLink button until the HomeLink
indicator begins to flash slowly.
When the indicator begins to flash
slowly, continue to hold the
HomeLink button and follow steps
1– 4 under Training a Button.1
2
Retraining a Button
Erasing CodesTo erase codes stored in all buttons,
press and hold the two outer buttons
until the HomeLink indicator begins to
flash (about 10 to 20 seconds), then
release the buttons.
If you have any problems programming
HomeLink, see the owner's manual included with
the device you are trying to program, call
HomeLink at (800) 355-3515 or visit
www.homelink.com.
If you sell the vehicle, make sure to
erase all codes.
The HomeLink Universal Transceiver built into your vehicle can be programmed to operate up to th\
ree
remote-controlled devices around your home, such as garage doors, lighti\
ng, or home security systems.
10 Ridgeline TRG_3ab:ExtraPages.qxd 7/6/2009 10:06 AM Page b3 2010 Ridgeline
